Eagle Quick Fix
High quality quick setting mortar
Description
Eagle Quickfix is a high quality, rapid-setting, polymer modified single component
thin-set mortar. It only needs water for installation of all types of natural stones and
tiles, vitrified or not and also impervious like porcelain, inside, on horizontal or vertical
surfaces. It has been specially conceived for fast-track projects either for residential or
commercial uses. Take note that rigorous attention must be taken to execute surface
preparation conform to trade practices and Eagle Black’s surface preparation
guidelines.
Surface Preparation
All surfaces to be covered shall be structurally sound, clean and free from traces of dust,
oil, grease, wax, paint, curing agent, coatings and loose particles. They must also be
exempt from any trace or presence of acids, concentrated alkalis, chemical cleaning
agent or any other materials that can reduce adhesion. Substrates like particleboard,
chipboard, Lauan, press wood or Masonite are not appropriate for thin-set mortar
products. The only recommended wood substrate for residential floors is exterior grade
plywood installed in an interior dry area. All concrete substrates shall be completely
cured and at least 28 days old, free from hydrostatic conditions and/or extreme humidity
problems. They must be roughened to completely remove all traces of paint, coating,
loosely bonded toppings, loose particles and construction debris. Ambient, surface and
product temperature must be superior to 10ºC (50ºF)and lower than 35ºC (95ºF) before
the installation and for the first 24 hours.
Application
Spread and scratch mortar on surface to be covered with flat edge of trowel. Quickly
add mortar and using notch side of the trowel, spread mortar uniformly, taking care to
trace ridge lines in the same straight line direction. Spread enough mortar so that the
surface can be covered in less than about 15 minutes. If ridges have slightly dried and
there is skin formation at the surface, there will be no adherence, mortar will have to be
removed and a fresh coat applied. Press tiles firmly with a back and forth motion across
ridges to obtain full mortar transfer at the back of tiles. Tiles must be embedded at 1/3
of their thickness in mortar. Never wet tiles prior to their application, if so, it must be
advised by tile manufacturer.
Mixing
In a clean container, pour 240 ml of fresh clean water per kilogram of Eagle Quickfix, add
gradually powder while mixing with a low-speed drill and mixer. Blend for 1 to 2 minutes
scraping recipient walls and paddle to obtain an homogeneous trowelable consistency.
Apply immediately. Occasionally remix while using it, with no water addition. Clean
working tools and hands with water while product is still fresh.
Yield
Approximate coverage for a 22.7 kg (50lb) bag :
Trowel 6 X 6 X 6 mm (¼” X ¼” X ¼”) : 8.4 m² (90 ft²)
Trowel 6 X 10 X 6 mm (¼” X 3/8” X ¼”) : 6.0 m² (70 ft²)
Condor Chimiques Inc.
2645 B, Terra-Jet, St-Cyrille-de-Wendover, Québec, J1Z 1B3
www.condor.pro
[email protected]
Phone.: 819-474-6661
Fax.: 819-474-6681
Eagle Quick Fix
High quality quick setting mortar
Curing
Warning
Protect surfaces from light traffic for 3 hours. Curing time may vary according to
temperature and humidity level. Make sure application is dry prior to allow light
traffic for grouting. Package
Available in bag of 22.7 kg grey or withe.
Storage
Store in a dry and fresh area. Shelf life is 12 months in its original non-opened
container.
Technical Data Table
CARACTERISTICS
CURE
Eagle Quick Fix
Pot life
30 minutes
Open time
15 minutes
Set time final ASTM C-191
45 / 65 minutes
CORROSIVE: This product contains a
cementitious blend and may cause
eyes, skin and respiratory system
irritation. When using this product:
Wear safety glasses, gloves and a
NIOSH approved anti-dust mask. Keep
out of reach of children.
FIRST AID TREATEMENT: Skin contact:
Wash with soap and water. Eye contact:
Flush eyes immediately and abundantly
with water for 15 minutes keeping
eyelids opened. Consult a physician
immediately. Ingestion: DO NOT
INDUCE VOMITING. Give water if
conscious. Keep victim warm and call
immediately a physician.
Shear Strenth ANSI
A118.1
Wall Tiles
28 days
2,18 Mpa (316 Psi)
Mosaics
28 days
3,64 Mpa (528 Psi)
Quarrys
28 days
3,47 Mpa (503 Psi)
Quarrys / Plywood
28 days
1,25 Mpa (181 Psi)
* Dry Time dependent of surface porosity and temperature.
Warranty
The customer shall verify of the suitability of this product for the intended purpose.
Applicator's skill, weather and surface conditions being beyond manufacturer's
control, we limit our liability to replacement of defective material only in sealed
container, within 1 year of proof of purchase. FOB plant.
Condor Chimiques Inc.
2645 B, Terra-Jet, St-Cyrille-de-Wendover, Québec, J1Z 1B3
www.condor.pro
[email protected]
Phone.: 819-474-6661
Fax.: 819-474-6681
Powered by TCPDF (www.tcpdf.org)