TIFR BALLOON FACILITY, HYDERABAD
PROPOSED HPC AND SUB - STATION BUILDING - BOQ
PART - A
S.No
Description
Unit
Qty
Rate in figures
Rate in words
1
Earth work in excavation by mechanical means
CM
479
(Hydraulic excavator) / manual means over areas
(exceeding 30cm in depth. 1.5 m in width as well as
10 sqm on plan) including disposal of excavated
earth, lead upto 50m and lift upto 1.5m, disposed
earth to be levelled and neatly dressed, in all kinds
of soil
2
Providing and Injecting Chemical Emulsion of
Chlorophyriphos emulsified concentrate 1% for preconstruction anti termite treatment and a chemical
barrier under and around the column pits, wall
trenches, basement plinth filling treatment of junction
of walls at floor treatment of soil along external
perimeter of building treatment of expansion joints
treatment of soils surrounding pipes and conduits
etc., with 10 years guarantee. Payment will be made
on measured plinth area of Ground floor.
SM
389
3
Providing and constructing Coursed rubble stone
masonry ( second sort) in walls, piers and
foundations and plinth, using approved stone laid,
well bonded, bedded and solidly hearted in cement
mortar 1:6, ( 1 cement, 6 coarse sand) joints
finished flush as work proceeds including curing. The
rate includes cost and conveyance of all materials,
lead and lifts etc., and provision for bond stones at
every 2m c/c in each course.
CM
125
4
Filling with the MURRUM brought from out side
trenches, plinth, soil to the sides of foundation in
layers of 200mm thick consolidating each deposited
layer by ramming watering.
CM
175
5
Filling available excavated earth (excluding rock) in
trenches, plinth, sides of foundations etc. in layers
not exceeding 20 cm in depth, consolidating each
deposited layer by ramming and watering, lead up to
50 m and lift up to 1.5 m.
CM
90
6
Providing and laying plain cement concrete,
machine mixed and mechanically vibrated, using 20
mm / 40mm and below size, crushed graded granite
aggregate as applicable in foundation trenches,
plinth, bed blocks, pockets etc, including curing etc
as directed by Engineer -in -charge .
1:2:4 mix (1 cement, 2 coarse sand, 4 stone
aggregate)
with 20 mm metal
1:4:8 mix ( 1cement, 4 coarse sand, 8 stone
aggregate)
with 40mm metal
Providing and laying machine mixed, mechanically
vibrated Reinforced cement concrete works M25
with
minimum
cement
content
375
Kgs
Cement/Cum. of Concrete using 20 mm and below
size crushed graded granite aggregate including
vibrating, curing for all heights and levels including
centering, shuttering, but excluding reinforcement.
CM
4.9
CM
27
Columns/Pedestals
CM
33.2
Footings
CM
62.2
7
Amount
8
9
10
A)
B)
11
Beams, lintel
CM
28.5
Plinth Beams
CM
10.5
Slab
CM
95.7
Sunshade
CM
1
Folded plate Slab for staircase
CM
3.8
Walls
CM
36
RCC Fins
CM
9.45
PCC 1:2:4 FOR DPC Providing and laying 50 mm
thick DPC in 1:2:4 mix with 6 to 20 mm size
aggregate and water proofing compound at the rate
of 1 kg per bag of cement .
Providing cold twisted HYSD bars of approved make
of reputed concern of FE 500 GRADE , for RCC
work including straightening, cutting, bending,
binding and placing in position all as per structural
drawings. The cost of binding wire shall not be paid
extra and will be at the contractor's cost.
SM
52
KG
34098
CM
SM
128.5
16
SM
271
Providing and fixing up to floor five level precast
cement concrete hollow block, including hoisting and
setting in position with cement mortar 1:3 (1 cement :
3 coarse sand), cost of required centering, shuttering
complete.
1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate
20 mm nominal size)
200mm thk
100mm thk masonry in CM 1:4,including 2 nos. of
6mm bars at every third course of block masonry.
The rate shall include cost of steel also. The rate
shall be applicable for all heights.
FLOORING
Providing and laying cement concrete flooring 1:2:4
(1 cement:2 coarse sand:4, 20mm nominal size
graded granite aggregate) finished with floating coat
of neat cement slurry etc, curing, necessary
formwork, shuttering , all labour, leads and lift, etc
complete. (FOR PLINTH PROTECTION ALROUND
and HPC flooring etc.
40mm thick with 20mm nominal size aggregate
12
62 mm thick cement concrete flooring with concrete
hardener topping, under layer 50 mm thick cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20mm nominal size) and top layer
12mm thick cement hardener consisting of mix 1:2
(1 cement hardener mix : 2 graded stone aggregate,
6mm nominal size) by volume, hardening compound
mixed @ 2 litre per 50 kg of cement or as per
manufacture’s specifications. This includes cost of
cement slurry, but excluding the cost of nosing of
steps etc. complete.
SM
30
13
Providing and fixing glass strips in joints of terrazo /
cement concrete floors 40 mm wide and 4 mm thick.
In item 12 above.
RM
90
14
Paver Blocks
Providing and laying factory made coloured
chamfered edge Cement Concrete paver blocks of
required strength, thickness & size/shape, made by
table vibratory method using PU mould, laid in
required colour & pattern over 50mm thick
compacted bed of fine sand, compacting and proper
embedding/laying of inter locking paver blocks
into the sand bedding layer through vibratory
compaction by using plate vibrator, filling the joints
with river sand and cutting of paver blocks as per
required size and pattern, finishing and sweeping
extra sand in footpath, parks, lawns, drive ways or
light traffic parking etc.
complete as per manufacturer's specifications &
direction of Engineering- Charge. 60mm thick C.C.
paver block of M-35 grade with approved colour,
design & pattern
15
16
SM
125
SM
126
SM
SM
12.6
2.5
Providing and laying vitrified floor tiles in different
sizes of 10mm thickness with water absorption less
than 0.08% and conforming to IS : 15622, of
approved make, in all colours and shades, laid on
20mm thick cement mortar 1:4 (1 cement : 4 coarse
sand), including grouting the joints with white cement
and matching pigments etc., complete.
Grouting the joints of flooring tiles having joints of 3
mm width, using epoxy grout mix of 0.70 kg of
organic coated filler of desired shade (0.10 kg of
hardener and 0.20 kg of resin per kg), including
filling / grouting and finishing complete as per
direction of Engineer-in-charge
Size of Tile 600x600 mm
Providing and laying vitrified floor tiles in different
sizes 10mm thickness with water absorption less
than 0.08% and conforming to IS : 15622, of
approved make, in all colours and shades, laid on 6
mm thick cement mortar 1:4 (1 cement : 4 coarse
and), including grouting the joints with white cement
and matching pigments etc., complete
17
Grouting the joints of flooring tiles having joints of 3
mm width, using epoxy grout mix of 0.70 kg of
organic coated filler of desired shade (0.10 kg of
hardener and 0.20 kg of resin per kg), including
filling / grouting and finishing complete as per
direction of Engineer-in-charge
Riser Size of Tile 600x600 mm
Providing and laying rectified Glazed Ceramic floor
tiles of size 300x300 mm having 7.3mm or more
thickness of 1st quality conforming to IS : 15622, of
approved make, in all colours, shades, except White,
Ivory, Grey, Fume Red Brown, laid on 20 mm thick
Cement Mortar 1:4 (1 Cement : 4 Coarse sand),
including pointing the joints with white cement and
matching pigments etc., complete
18
False Flooring 600 X 600 X 600 mm
The Access raised floor shall be medium grade
panel or equivalent, and also point load of 6.6 KN
(660kg) / over 25mm sq. and UDL of 21.50 KN/m2
(2150kg/sqmtr) ; panels manufactured from steel
with lightweight cementitious core in the size 600 X
600 X 35 mm.The top panel shall be finished with
high abrasion, anti-static High Pressure Laminate in
size 600mm x 600mm x 1mm with beading on all
sides to provide protection of edges.
The bottom of the panel shall be embossed in
hemispherical shape to give strength and flexural
rigidity. The entire panel shall be finished with electro
deposition of cathodic epoxy paint on the exposed
surface for lifetime protection and shall be Zinc
Whisker free.
Pedestals (600mm) design shall conform to speedy
assembly and removal for relocation and
maintenance. Pedestal base to be permanently
secured to portion on sub-floors, pedestal assembly
shall provide easy adjustment of leveling and
accurately aligned panel to ensure lateral resistance.
It shall be designed to avoid any rattle or squeaks. It
consists of 100x100x2mm thick galvanized base
plate die pressed orbitally riveted to 25mm OD 2.20
mm thick G.I./epoxy coated pipe to engage, the
pedestal head assembly consisting of
75mmx75mmx3.5mm embossed ribbed head with
four holes with steel pin for panel location for fasting
and locating of tiles , mechanically locked to
corresponding threaded stud 16mm dia OD and
which is designed to engage the pedestal base
assembly, the assembly shall provide a range of a
height adjustment up to 50mm with the help of two
check nuts . Pedestal shall be permanently fixed to
sub floor by application of Araldite and 4 nos. wedge
expansion type expansion hold fasteners with
threaded dia of 6mm dia.
Stringers system is all steel construction hot dipped
galvanized rectangular snap lock channel
570x25x32x0.80mm thick having notches for snap
locking stringers to aluminium pedestals prepunched counter sunk holes are provided at both
ends for securing the stringers on to the pedestal
head ensuring maximum lateral stability in all
directions, the grid formed by the pedestal and
stringer assembly shall receive the floor panel, this
system shall provide adequate solid, rigid support for
access floor panel, the system shall provide a
minimum clear uninterrupted height of 600 mm
between the bottom of the floor for electrical
conduits and wiring etc.
“Design calculations supporting the desired load
carrying capacity of the flooring shall be
submitted by the contractor before use”
19
Paver Blocks
Providing and laying 60mm thick factory made
cement concrete
Grass paver block of M -30 grade made by block
making
machine with strong vibratory compaction, of
approved size, design & shape, laid in required
colour and pattern over and including 50mm thick
compacted bed of coarse sand, filling the joints with
fine sand etc. all complete as per the direction of
Engineer-in-charge. The rate to include providing
and spreading 50mm thick red earth mixed with
manure filled in the voids of the paver blocks.
SM
153
SM
30
20
21
22
23
24
25
26
27
28
Kota stone slabs 20 mm thick in risers and treads of
steps, no joints allowed, skirting, dado and pillars
laid on 12 mm (average) thick cement mortar 1:3 (1
cement: 3 coarse sand) and jointed with grey cement
slurry mixed with pigment to match the shade of the
slabs, including rubbing and polishing complete
SM
13.5
Extra for pre finished nosing in treads of steps of
Kota stone slab
Providing and laying cement plaster (sponge finish)
of 18mm thick in CM, 1st coat 12mm th in CM (1:5)
and 6mm th 2nd coat in CM (1:3) for inside walls
etc., including scaffolding, at all heights and levels,
curing etc., complete as per the specifications and
drawings. The rate should include making good
chases of electrical conduits, boxes, pipes etc in
cement mortar 1:3 and necessary chicken mesh.
Rate to include additional thickness if required to
achieve perfect line and level. No extra will be
payable on this account.
RM
30
INTERNAL PLASTERING
INCLUDING GROOVES where needed
SM
553
CEILING PLASTERING 6mm th in CM (1:3)
INCLUDING GROOVES where needed
Pointing on stone work with cement mortar 1:3 (1
cement : 3 fine sand).
SM
521
SM
111
EXTERNAL PLASTERING
INCLUDING GROOVES
SM
651
Providing and applying white cement based putty of
Birla/JK make , 2 mm thickness over plastered
surface to prepare the surface even and smooth
complete including supplying and applying 2 coates
of premium acrylic emulsion paint of approved brand
and manufacture to give an even shade (two or more
coats) over and including water thinnable priming
coat with cement primer.
Distempering with oil bound washable distemper of
approved brand and manufacture to give an even
shade (two or more coats) over and including water
thinnable priming coat with cement primer
SM
553
SM
521
SM
419
SM
325.5
Providing and laying cement plaster (sponge finish)
of 18mm thick in CM, 1st coat 12mm th in CM
(1:5) and 6mm th 2nd coat in CM (1:3) for outside
walls etc., including scaffolding, at all heights and
levels, curing etc., complete as per the specifications
and drawings. The rate should include making
good chases of electrical conduits, boxes, pipes etc
in cement mortar 1:3 and necessary chicken mesh.
Rate to include additional thickness if required to
achieve perfect line and level. No extra will be
payable on this account.
Finishing walls with textured exterior paint of required
shade : 13.45.1 New work (Two or more coats
applied @ 3.28 ltr/10 sqm) over and including
priming coat of exterior primer applied @ 2.20kg/10
sqm
Providing and painting two or more coats of
WATER PROOF CEMENT PAINT of approved
shade, including one coat of cement primer
application, including cost and conveyance of all
materials, leads and lifts, scaffolding, curing, labour
charges etc for external walls as directed. Rate to be
applicable at all heights, level surfaces and textures.
29
Providing and fixing false ceiling at all height
including providing and fixing of frame work made of
special sections, power pressed from M.S. sheets
and galvanized with zinc coating of 120 gms/sqm
(both side inclusive) as per IS : 277 and consisting of
angle cleats of size 25 mm wide x 1.6 mm thick with
flanges of 27 mm and 37mm, at 1200 mm centre to
centre, one flange fixed to the ceiling with dash
fastener 12.5 mm dia x 50mm long with 6mm dia
bolts, other flange of cleat fixed to the angle hangers
of 25x10x0.50 mm of required length with nuts &
bolts of required size and other end of angle hanger
fixed with intermediate
G.I. channels 45x15x0.9 mm running at the spacing
of 1200 mm centre to centre, to which the ceiling
section 0.5 mm thick bottom wedge of 80 mm with
tapered flanges of 26 mm each having lips of 10.5
mm, at 450 mm centre to centre, shall be fixed in a
direction perpendicular to G.I. intermediate channel
with connecting clips made out of 2.64 mm dia x 230
mm long G.I. wire at every junction, including fixing
perimeter channels 0.5 mm thick 27 mm high having
flanges of 20 mm and 30 mm long, the perimeter of
ceiling fixed to wall/partition with the help of rawl
plugs at 450 mm centre, with 25mm long dry wall
screws @ 230 mm interval, including fixing of
gypsum board to ceiling section and perimeter
channel with the help of dry wall screws of size 3.5 x
25 mm at 230 mm c/c,
including jointing and finishing to a flush finish of
tapered and square edges of the board with
recommended jointing compound , jointing tapes ,
finishing with jointing compound in 3 layers covering
up to 150 mm on both sides of joint and two coats of
primer suitable for board, all as per manufacturer's
specification and also including the cost of making
openings for light fittings, grills, diffusers, cutouts
made with frame of perimeter channels suitably
fixed, all complete as per drawings, specification and
direction of the Engineer in Charge but excluding the
cost of painting with : Fully Perforated Gypsum
Plaster Board of size 1200 x 2400x12.5 mm having
approx. 15 % perforated area with
perforation size and pattern as approved by the
Engineering- charge and as per manufacturer's
specification, with all 4 side tapered and backed by
acoustical tissue with NRC value not less than 0.60
30
SM
150
SM
7.2
Providing and fixing aluminium work for doors,
windows, ventilators and partitions with extruded built
up standard tubular sections/ appropriate Z sections
and other sections of approved make conforming to
IS: 733 and IS: 1285, fixing with dash fasteners of
required dia and size, including necessary filling up
the gaps at junctions, i.e. at top, bottom and sides
with required EPDM rubber/ neoprene gasket etc.
Aluminium sections shall be smooth, rust free,
straight, mitred and jointed mechanically wherever
required including cleat angle, Aluminium snap
beading for glazing / paneling, C.P. brass / stainless
steel screws, all complete as per architectural
drawings and the directions of Engineer-in-charge.
Polyester powder coated aluminium (minimum
thickness of polyester powder coating 50 micron)
With float glass panes of 5.50 mm thickness
Including Handle etc complete
31
ROLLING SHUTTER Supply, fabrication and fixing
of MS rolling shutter of the following specifications
including grill window of 300 mm height at eye level
for visibility even in closed position. Code:
Conforming to IS 6248 – 1979 Type: Self Coiling
type (manual) Curtains: Interlocking cold rolled lath
section of 0.8 mm thickness. Lock plate : MS sheet
of 3.15 mm thick reinforced with MS angles of 35 x
35 mm. Guide channel : MS sheets of 3.5 mm thick
Bracket Plate : MS Sheet of 0.9 mm thick Hood
Covers : MS sheet of 0.9 mm thick Locking handle :
To be provided suitably. Rate shall include providing
and fixing holdfasts and painting two coats of enamel
paint of approved make and shade over two coats of
zinc phosphate primer.
SM
12.2
32
Providing and fixing 12 mm thick frameless
toughened glass door shutter of approved brand and
manufacture, including providing and fixing top &
bottom pivot & spring type fixing arrangement and
making necessary holes etc. for fixing required door
fittings, all complete as per direction of Engineer-incharge
FLUSH DOORS - ( FD )
Supply and fixing of Commercial Flush door single
leaf shutters with saal wood frame of size 100x65mm
and shutter made of 30mm thick commercial flush
door finished with 1mm thk. Laminate on both sides
including finishing and polishing the wooden
surfaces with sealer-melamine matt finish tinted to
approved colour and shade as per drawing. Door will
have provision of necessary hardware like handles,
aldrops, door lock etc., complete for the finished item
of work.
SM
11.9
SM
5.67
No
3
SM
0.36
33
34
35
Providing and fixing double action hydraulic floor
spring of approved brand and manufacture
conforming to IS : 6315, having brand logo
embossed on the body / plate with double spring
mechanism and door weight up to 125 kg, for doors,
including cost of cutting floors, embedding in floors
as required and making good the same matching to
the existing floor finishing and cover plates with
brass pivot and single piece M.S. sheet outer box
with slide plate etc. complete as per the direction of
Engineer-in-charge.
Specifications same as above but for ventilator with
4mm glass panes
36
Providing & fixing 50mm thk thermocole with chicken
mesh on both sides between 2 brick walls for thermal
insulation with all required material complete for the
finished item of work
SM
210
37
Providing and fixing gates, hand rail of approved size
by welding etc. to steel ladder railing, balcony railing,
staircase railing and similar works, including applying
priming coat of approved steel primer.
Kg
2500
Kg
1281
38
39
Gates , Railing Similar works
Steel work welded in built up sections/ framed work,
including cutting, hoisting, fixing in position and
applying a priming coat of approved steel primer
using structural steel etc. as required.
In trench cover use of 6mm thick ms chequered
plate etc wherever required, all complete
WATER PROOFING
Providing and laying integral cement based water
proofing treatment including preparation of
roofs,balconies,terraces etc consisting of following
operations.
a) Applying and grouting a slurry coat of neat cement
using 2.75 kg/sqm. Of cement admixed with
proprietary water proofing compound conforming to
IS.2645 over the RCC slab including the surface
before treatment.
b) Laying cement concrete using broken bricks/brick
bats 25 mm to 100 mm size with 50% of cement
mortar 1:5 ( 1 cement : 5 coarse sand) admixed with
proprietary water proofing compound conforming to
IS 2645 over 20 mm thick layer of cement mortar of
mix 1:5(1 cement : 5 coarse sand) admixed with
proprietary water proofing compound conforming to
IS :2645 to required slope and treating similarly the
adjoining walls up to 300 mm height including
rounding of junctions of walls and slabs.
SM
440
KG
460
NO
1
NO
1
RM
20
C) After two days of proper curing applying a second
coat of cement slurry admixed with proprietary water
proofing compound conforming to IS : 2645.
D) Finishing the surface with 20 mm thick joint less
cement mortar of mix 1:4 (1 cement : 4 coarse sand)
admixed with proprietary water proofing compound
conforming to IS :2645 and finally finishing the
surface with trowel with neat cement slurry and
making of 300 X 300 mm square.
40
E) The whole terrace so finished shall be flooded
with water for a minimum period of two weeks for
curing and for final test. All above operations to be
done in order and as directed and specified by the
Engineer-in-charge.
Providing and fixing MS grill fabricated from MS
flat/square bar as per approved design including
painting with two coats of red oxide and two coats of
synthetic enamel paint as per DSR item no:9.48,
9.48.1
SANITARY ITEMS
1
2
3
Providing and fixing of E.W.C (cascade white
Parryware or equivalent) suite including cistern , seat
cover. Also supplying and connecting 12mm CP
angle cock OF (JAQUAR make) with 12mm PVC
connection.
Providing and fixing of Wash basin with CI/MS
brackets , 15mm CP brass Pillar taps of (Jaquar or
equivalent), 32mm waste coupling including painting
of fittings etc complete
630x450 with a pair of 15mm CP taps
CPVC
Providing and fixing Chlorinated Polyvinyl Chloride
(CPVC) pipes, having thermal stability for hot & cold
water supply, including all CPVC plain & brass
threaded fittings, i/c fixing the pipe with clamps at
1.00 m spacing. This includes jointing of pipes &
fittings with one step CPVC solvent cement and the
cost of cutting chases and making good the same
including testing of joints complete as per direction
of Engineer in Charge. Concealed work, including
cutting chases and making good the walls etc.
a) 15mm dia
b) 25mm dia (external work)
RM
30
a) 100mm dia
RM
20
b) 75 mm dia
RM
20
150mm dia
RM
40
6
Providing and fixing CI pipes of 100 dia, to
columns, brick work etc, with suitable MS clamps at
1m c/c, required hardware, labour, pipe accessories
like shoe end, drop end etc.
RM
105
7
Providing and fixing trap of self cleansing design with
screwed down or hinged grating with or without vent
arm complete, including cost of cutting and making
good the walls and floors : 17.60.1 100 mm inlet and
100 mm outlet
NO
2
8
GATE VALVES
Providing and fixing heavy duty, gun metal full way
gate valves tested up to 300 lbs/Sq.in ( 20kg/cm2) of
approved quality to IS 778-1971.
a) 25mm dia
NO
2
Supplying & fixing bib cock 15mm of approved
make (Jaquar 035)
Each
4
Supplying & fixing of soap dish of approved make
(Jaquar 1131)
Each
4
4
5
9
10
Providing and fixing cast iron soil pipes, waste and
vent pipes (IS 1 3989) only including all fittings
(plain or with inspection door) e.g bends, junctions,
offsets, access piece, caulking with cement including
cutting holes in walls and floors, and making good.
GI bat clamps of adequate size shall be provided at
every 2m c/c or at every joint. Rate to include
painting in 3 coats of enamel paint with primer and
surface preparation, testing for leaks etc., complete.
Providing and laying in position salt glazed
stoneware pipes conforming to IS 651, to correct
alignment and gradient as per the drawing including
excavation of trenches in all types of soil, sealing
the joints with tarred gasket and finishing with 1:3
cement mortar and testing of joints, refilling the
trenches with excavated earth, watering, ramming
etc.,complete.
11
Supplying & fixing of TOILET PAPER HOLDER
(Jaquar 1151)
Each
4
12
Providing and fixing square-mouth S.W. gully trap
class SP-1 complete with C.I. grating brick masonry
chamber with water tight C.I. cover with frame of 300
x300 mm size (inside) the weight of cover to be not
less than 4.50 kg and frame to be not less than 2.70
kg as per standard design
NO
4
13
Constructing masonry Chamber 90x90x100 cm
inside, in brick work in cement mortar 1:4 (1 cement :
4 coarse sand) for sluice valve, with C.I. surface box
100 mm top diameter, 160 mm bottom diameter and
180 mm deep (inside) with chained lid and RCC top
slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size ), i/c necessary
excavation, foundation concrete 1:5:10 (1 cement : 5
fine sand : 10 graded stone aggregate 40 mm
nominal size ) and inside plastering with cement
mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick,
finished with a floating coat of neat cement complete
as per standard design :
NO
4
14
Providing and placing on terrace (at all floor levels)
polyethylene water storage tank, ISI : 12701 marked,
with cover and suitable locking arrangement and
making necessary holes for inlet, outlet and overflow
pipes but without fittings and the base support for
tank
Ltrs
1000
15
Making soak pit complete as per standard design &
drawing.
NO
1
16
Providing & constructing Septic tank for 25 users.as
per the drawing
NO
1
17
Providing percolation pit of size 10.75x5.7m x 1m 1 No as per the drawing attached
NO
1
18
Providing percolation pit of size 4m x 3m x 1m - 4
nos as per the drawing attached
Nos
4
Total (PART - A)
Discount if any
PART (B)
Sr#
Item
Base
Value(Rs)
BV
B1
Any unforeseen item not
covered above, executed
from CPWD Delhi
Schedule of Rates 2013
(+)Plus/()Minus(both
in symbol
and words)
Percentage Effective
(+)Plus/(Amount*(Rs)
)Minus(both
in symbol
and words)
P
9,00,000
NOTE:
Effective amount in B1 shall be BV x (1 + P/100) for plus percentage and BV x (1 - P/100) for minus percentage
-----------------------------------------
Grand Total [Total Part (A) + B1] =
-----------------------------------------
Signature and Stamp of the bidder