LineLED Flex 18 Horizontal plan bendable LED strip - 24 VDC
LineLED Flex 18 is a small profile, high output
LED strip specially designed for installations
with horizontal plan bend. Bending sections
every 1.30” on center allow the LineLED
Flex 18 to fit around tight curves.
Applications: Indoor only - cove
lighting, architectural reveals, under
banister, general ambient lighting,
etc.
Mounting
LineLED Flex18 strip is equipped with 3M
self-adhesive tape. The strip must be adhered to either a Luminii aluminum profile or
an unpainted aluminum surface. For other
surfaces the HST Aluminum heat sink tape
will be required to reach the rated 50,000
hours average life.
Operating voltage
24 VDC
Approvals
Class 2 damp listed
Average life
50,000 hours
Warranty
5 years
Technical information
MODEL
PRODUCT DIMENSIONS
LLFLEX18
LEDS/ft
18
Light output
3000K
225 lum/ft
Average power
consumption
(for 15’ section)
2.65 W/ft
Ordering increment
4.00”
Maximum run length
22 ft
Bends up to 90°
0.39”
0.05”
0.39” W
0.05” H
Dimensions
Multiplier
(referenced from 3000K)
1”
SECTION START/END OPTIONS
CCT INFO/LUMEN MULTIPLIER
Color temperature
Bends every
1.30” on
center
TM-30-15
CRI
Rf
Rg
2200K
0.87
82
81
99
2400K
0.73
98
95
101
2700K
0.81
98
95
102
3000K
1.00
91
90
101
4100K
1.28
93
88
96
Soldered Leads
No Connection
Ordering code
MODEL
COLOR TEMPERATURE
SECTION START
SECTION END
LLFLEX18
LLFLEX18
22K
- 2200K
- 2400K
- 2700K
- 3000K
- 4100K
SL
SL - Soldered lead
wires (72”)
NC - No connector
SL
SL - Soldered lead
wires (72”)
NC - No connector
REV2.2
22K
24K
27K
30K
41K
page 1 of 6
LENGTH
4
4” increments - up to 22’
www.luminii.com
tel: 224-333-6033
LineLED Flex 18 Horizontal plan bendable LED strip - 24 VDC
TM-30-15: Data
22K CCT
24K CCT
27K CCT
30K CCT
41K CCT
REV2.2
page 2 of 6
www.luminii.com
tel: 224-333-6033
LineLED Flex 18 Horizontal plan bendable LED strip - 24 VDC
Power consumption per linear foot
loads tested with PSD series of power supplies (page 4)
POWER CONSUMPTION PER FOOT
Length of strip (LF)
W/ft
Totalwattage
1
3.35
3.35
2
3.35
6.70
3
3.30
9.90
4
3.25
13.00
5
3.20
16.00
6
3.15
18.90
7
3.10
21.70
8
3.05
24.40
9
3.00
27.00
10
2.95
29.50
11
2.90
31.90
12
2.80
33.60
13
2.75
35.75
14
2.70
37.80
15
2.65
39.75
16
2.60
41.60
17
2.55
43.35
18
2.50
45.00
19
2.45
46.55
20
2.40
48.00
21
2.35
49.35
22
2.30
50.60
Accessories
Mounting clip:
recommended at every 12” when
LineLED strip is facing down.
Part # CL-1
0.19”
Heat sink tape:
Splice Box:
no extrusions are ordered.
splice box, black.
included with LineLED strip when
0.05”
Part # HST
0.40”
1.00”
low voltage, 4 terminal
Part # LVSP-4T -BK
0.90”
0.23”
2.00”
3.00”
1.90”
REV2.2
page 3 of 6
www.luminii.com
tel: 224-333-6033
LineLED Flex 18 Horizontal plan bendable LED strip - 24 VDC
Power supply
See fixture and power supply instructions & spec sheet for wiring information. Dimming possible in select models - view Luminii website for list of compatible dimmers.
Non-Dimming:
MODEL
PSV
PSV - PSV Series
POWER
OUTPUT
40
40 - 40 W
60 - 60 W
96 - 96 W
DIMMING
24V
24 - 24 VDC
LOCATION
U2ND
U2ND - Non Dimming
D
D - Dry Location
IP65 - Wet Location
MODELS
PSV Dry
PSV Wet
A Length
9.2”
9.5”
B Width
3.4”
4.12”
C Depth
1.9”
2.3”
C
A
B
Dimming 0-10V:
C
MODEL
POWER
OUTPUT
DIMMING
PS010V
PS010V - 0-10V Power Supply
dims down to 0%
3X100
3X100 - 3 X 100 WATT
24
24 - 24 VDC
LIN
LIN - Linear
LOG - Logarithmic
B
- features eldoLED’s LINEARdrive configurable 0-10V drivers
MODEL
PSV
PSV - PSV Series
dims down to 5%
POWER
40
40 - 40 W
60 - 60 W
96 - 96 W
OUTPUT
MODELS
PSD010V
A Length
15.75”
B Width
6.60”
C Depth
4.80”
DIMMING
24V
24 - 24 VDC
A
LOCATION
U2DIM
U2DIM - Dimming 0-10V
D
D - Dry Location
IP65 - Wet Location
MODELS
PSV Dry
PSV Wet
A Length
9.2”
9.5”
B Width
3.4”
4.12”
C Depth
1.9”
2.3”
C
A
B
Dimming Magnetic low voltage:
MODEL
PSD
PSD - PSD Series
dims down to 0%
REV2.2
POWER
48
48 - 48 W
96 - 96 W
288 - 288 W (3x 96W)
OUTPUT
24
24 - 24 VDC
INPUT
B
C
Blank - 120 V
240 - 240 V
277 - 277 V
MODELS
PSD 48
PSD 96
PSD 288
A Length
11.25”
11.25”
13.06”
B Width
3.42”
3.42”
8.42”
C Depth
3.42”
3.27”
4.47”
page 4 of 6
A
www.luminii.com
tel: 224-333-6033
LineLED Flex 18 Horizontal plan bendable LED strip - 24 VDC
Power supply
See fixture and power supply instructions & spec sheet for wiring information. Dimming possible in select models - view Luminii website for list of compatible dimmers.
Dimming Electronic low voltage:
MODEL
CVE
CVE - CVE Series
dims down to 0.1%
CIRCUIT x POWER
48 48X2D
48X3D
48X4D
96 96X2D
96X3D
96X4D
OUTPUT
48
40W
- 2 x 40W
- 3 x 40W
- 4 x 40W
96W
- 2 x 96W
- 3 x 96W
- 4 x 96W
INPUT
24V
24 - 24 VDC
cover
Blank - 120 V
277 - 277 V
C
A
B
MODELS
Single circuit
Dual circuit
Three circuit
Four circuit
A Length
11.6”
11.5”
11.5”
11.5”
B Width
2.3”
4.0”
5.9”
7.75”
C Depth
1.3”
1.9”
1.9”
1.9”
DMX & DALI:
MODEL
PSDMX
PSDMX - DMX Power Supply
PSDALI - DALI Power Supply
dims down to 0%
C
POWER
OUTPUT
3X100
3X100 - 3 X 100 WATT
24
24 - 24 VDC
B
- Features eldoLED’s LINEARdrive configurable dimmable drivers
MODELS
PSDMX
PSDALI
A Length
15.75”
15.75”
B Width
6.60”
6.60”
C Depth
4.80”
4.80”
A
Luminii is a Lutron OEM Advantage Partner
MODEL
B
MODEL
LTEA4U1UKL-CV240
Lutron – Hi-lume™ 1% 2-wire
LED driver (120V forward phase only)
MODELS
LTEA
L3DA
A Length
4.89”
4.89”
B Width
2.66”
2.66”
C Depth
4.00”
4.00”
C
MODEL
L3DA4U1UKL-CV240
Hi-lume™ 1% EcoSystem Voltage
LED Driver
B
A
L3D0-96W24V-U
Hi-lume™ 0.1% EcoSystem Voltage
LED Driver with Soft-On, Fade-to-Black™
MODELS
L3DO
A Length
10.50”
B Width
5.50”
C Depth
2.00”
A
C
REV2.2
page 5 of 6
www.luminii.com
tel: 224-333-6033
LineLED Flex 18 Horizontal plan bendable LED strip - 24 VDC
Optional mounting channels - Single row LEDs
Alu-Roun d
Alu-Corner
Alu-45
0.99”
0.94”
1.20”
0.72”
0.33”
0.69”
CL F N
CL HF F
Slim Line 7 *
CL HF F
Recessed Slim Line 7 *
Slim Line 15
0.69”
0.69”
0.95”
0.27”
0.59”
0.27”
0.69”
CL HF F N M
CL HF F N M
Recessed Slim Line 15
CL HF F N M
Alu-Fl at
0.63”
Alu-Wall
0.95”
2.05”
0.59”
0.30”
2.76”
0.69”
CL HF F N M
CL HF F
Slim Wi de 8
2.36”
CL F
Recessed Slim Wi de 8
Slim Wi de 15
0.88”
0.88”
1.16”
0.61”
0.33”
0.30”
0.88”
CL HF F
CL HF F
Alu- ETC
CL HF F
1.45”
0.87”
1.77”
0.81”
CL F
Lens options
CL
F
HF
N
M
REV2.2
Clear
Frosted
Half (50%) frosted
Narrow beam frosted
Medium beam frosted
Installation
Ordering
All mounting channels are field cuttable
using miter saw with circular blade
suitable for cutting aluminum.
Extrusions are sold separately. View
respective specsheets for details on
ordering extrusions and their accessories
(endcaps, mounting brackets, etc).
page 6 of 6
www.luminii.com
tel: 224-333-6033