Construction Guide
Version Index
Version
1.0
1.1
Date
05.10.15
10.02.16
Issuer
HY
JW
Amendments Made / Reason
NEW & REVISED MANUAL FOR ASSESSMENT
Cover Note
The drawings in this document supersede previous drawing details submitted. Some of the drawings have
been previously approved under different drawing numbers.
Please see below:
ISOSC-013B superseded by SEC/SAP/32100/REVA
ISOSC-012A superseded by SEC/SAP/32200/REVA
ISOSC-014B superseded by SEC/SAP/32300/REVA
ISOSC-015B superseded by SEC/SAP/32400/REVA
Section 1 – Introduction
Securiclad Introduction/Product Information
Overview of the LPS1175 scheme (SR ratings explained)
Manufacturing Approval
Technical Details:- Acoustic, Structural Span Detail Wall/Ceiling – Max Span
 Fire
 Approved Products By Others
 Health & Safety
 Maintenance
Installation Guide
Scope of Assessment: Walls/Ceilings – scope from BRE
Section 2 – Panel Joint Details





Wall – SR2,3,4 and Options
Ceilings– SR2,3,4 and Options <3000mm
Panel Detail for Double Skin Options
Ceilings– SR,3,4 and Options >3000mm
Re-enforced Panel Options
Section 3 – Wall Details



Corner Joints
Partition wall with angle or channel
Panel to existing (non securiclad) wall
Section 4 - Ceiling Details



Ceiling details
Intermediate joints
Ceiling supported by steel beam
Section 5 -Floor Details



Standard floor fixing detail
Raised floor detail
Dual panel fixing detail
Section 6 – Joints





Wall Joints
Start & Finish - Including angles and fixings
Panel to existing steelwork
Vertical Wall Joint With Header Above Door
Vertical Wall Joint Without Header above Door
Section 7 - Service Penetrations




Standard small penetrations
Multiple service penetrations
Servicing large apertures
Frame out channel options
Section 8 – Apertures





Channel options
Angle options
End Post
Corner Post
Inline Post
Section 9 – Small Enclosure


Small Enclosures
Locking Mechanism
Section 10 – Flashings & Fixings


Flashing options
Fixings
Section 11 – Impact of Louvers

Louver options to LPS1175
DRAWING INDEX
Code
SEC/PAN/10000/REVA
SEC/ACC/20000/REVA
SEC/SAP/30000/REVA
SEC/DET/40000/REVA
SEC/FIX/50000/REVA
SEC/APO/60000/REVA
= Panel
= Accessories
= Securiclad Approved Product
= Detail
= Fixing
= Approved Product By Others
Drawing
Section 2
Drawing Number
SR2 Panel Joint Detail Wall
SR2 Panel Joint Detail Ceiling
SR3 Panel Joint Detail Wall
SR3 Panel Joint Detail Ceiling <3000mm
SR4 Panel Joint Detail Wall
SR4 Panel Joint Detail Ceiling <3000mm
Double Skin Panel Joint Detail Wall
Double Skin Panel Joint Detail
Ceiling <3000mm
SR3 Ceiling >3000mm
SR4 Ceiling >3000mm
SR3 Reinforced Panel Wall
SR3 Reinforced Panel Ceiling < 3000
SR4 Reinforced Panel Wall
SR4 Reinforced Panel Ceiling < 3000
SR3 Reinforced Ceiling > 3000
SR4 Reinforced Ceiling > 3000
SEC/PAN/10000/REVA
SEC/PAN/10100/REVA
SEC/PAN/10200/REVA
SEC/PAN/10300/REVA
SEC/PAN/10400/REVA
SEC/PAN/10500/REVA
SEC/PAN/10600/REVA
SEC/PAN/10700/REVA
SEC/PAN/10800/REVA
SEC/PAN/10900/REVA
SEC/PAN/11000/REVA
SEC/PAN/11100/REVA
SEC/PAN/11200/REVA
SEC/PAN/11300/REVA
SEC/PAN/11400/REVA
SEC/PAN/11500/REVA
Section 3
Corner Post Detail Tamper
Corner Post Detail Bolt
Partition Wall Angle Fixed
Partition Wall Channel Fixed
Free Standing Wall Full Panel
Free Standing Wall Narrow Panel
SEC/DET/40000/REVA
SEC/DET/40100/REVA
SEC/DET/40200/REVA
SEC/DET/40300/REVA
SEC/DET/41700/REVA
SEC/DET/41800/REVA
Section 4
Ceiling Detail
Ceiling Support Bolted
Ceiling Support Tamper
Ceiling Support Steel Beam
SEC/DET/40400/REVA
SEC/DET/40500/REVA
SEC/DET/40600/REVA
SEC/DET/40700/REVA
Section 5
Channel Fixing
Raised Floor Detail
Wall Panel to Raised Floor Detail
Dual Panel Floor Fix
SEC/DET/40800/REVA
SEC/DET/40900/REVA
SEC/DET/41100/REVA
SEC/DET/41200/REVA
Section 6
Horizontal Wall Joint
Starting Abutment
Finishing Abutment
Structural Steel & Panels
Door with Header Panel
Door without Header Panel
SEC/DET/41300/REVA
SEC/DET/41400/REVA
SEC/DET/41500/REVA
SEC/DET/41600/REVA
SEC/DET/41900/REVA
SEC/DET/42000/REVA
Section 7
Single Penetration
Multi Penetration
Letterbox
Set Drawing Unprotected
Frame-out Channels
SEC/SAP/32100/REVA
SEC/SAP/32200/REVA
SEC/SAP/32300/REVA
SEC/SAP/32400/REVA
SEC/SAP/32500/REVA
Section 8
All Apertures
C13 Detail
C11 Detail
C10 Detail
A12 Detail
A11 Detail
A10 Detail
End Post Tamper
End Post Bolt
Inline Post Tamper
Inline Post Bolt
Corner Post Bolt
Corner Post Tamper
SEC/SAP/30000/REVA
SEC/SAP/30100/REVA
SEC/SAP/30300/REVA
SEC/SAP/30400/REVA
SEC/SAP/30500/REVA
SEC/SAP/30600/REVA
SEC/SAP/30700/REVA
SEC/SAP/30800/REVA
SEC/SAP/30900/REVA
SEC/SAP/31000/REVA
SEC/SAP/31100/REVA
SEC/SAP/31200/REVA
SEC/SAP/31300/REVA
Section 9
Small Enclosure With Header panel
Small Enclosure Without Header panel
Door Locking Mechanism
Door Posts and Lintel
SEC/SAP/31400/REVA
SEC/SAP/31500/REVA
SEC/SAP/31600/REVA
SEC/SAP/31700/REVA
Section 10
All Flashings
P1 Detail
P2 Detail
P3 Detail
P4 Detail
P5 Detail
Available Fixings
SEC/ACC/20000/REVA
SEC/ACC/20100/REVA
SEC/ACC/20200/REVA
SEC/ACC/20300/REVA
SEC/ACC/20400/REVA
SEC/ACC/20500/REVA
SEC/FIX/50000/REVA
Section 11
High Performance Security
Ventilation Louvres
SEC/APO/60000/REVA
SECTION
1
INTRODUCTION
Introduction to Securiclad:
Securiclad is a premium modular composite panel system designed and manufactured to protect high risk
areas, from data centres and government infrastructure, to utilities facility control rooms, banks, hazardous
material storage sites and more.
Developed to withstand determined attack from a wide range of tools and firearms, Securiclad is the ideal way
to safeguard a business, facility, goods or home.
Rigorously tested, it is approved for Government use by the Centre for the Protection of National
Infrastructure (CPNI) and provides a high security panel solution to Loss Prevention Standard (LPS) 1175
Security Rating (SR) 2, 3 and 4.
The Securiclad panel also holds the prestigious European EN1063 Ballistic Standard BR2, BR3 and BR4
certification.
Securiclad Product Information:
Securiclad is available in a variety of different compositions in order to satisfy a broad range of differing
security requirements.
Its high security level and innovative design means that it is ideal for the construction of secure environments
to protect areas containing servers, sensitive data and documents, hazardous substances, high value items and
pharmaceuticals. The system is quick and easy to install, with minimal disruption. It is entirely bespoke, can be
designed to specification and offers a complete modular solution including wall, ceiling and floor panels –
Certificate Number 142C & 142D.
Securiclad is weather and water resistant, making it suitable for both internal and external applications.
It can be used as a ‘standalone’ wall or partition as well as a complete modular secure enclosure. Securiclad
can be installed in new buildings or retro-fitted to an existing site.
Securiclad is also pre-finished, negating the need for wet or hot trade requirements. This provides a substantial
cost saving in terms of materials, turnaround time and labour when compared to more traditional building
methods.
It is available in a wide range of core types to satisfy insulation and fire rating requirements.
Securiclad can be offered as a turnkey solution, via approved and certified personnel or on a supply-only basis
for contractors who prefer to install the system themselves (using this document). Securiclad can also be
supplied fully assembled as a smaller kiosk, guard hut or small storage space.
Securiclad provides a premium, physical security barrier which can be used wherever there is a requirement to
safeguard high risk areas, protect critical equipment, or provide a last line of defence against acts of terrorism,
theft or vandalism.
The high security, modular composite panel solution Securiclad provides is used across a wide range of
industry sectors across a broad range of applications.
Securiclad overcomes a number of on-site restrictions posed by traditional building methods, it can be
designed to specification and offers heightened security solutions for rooms in a building, entire external
building envelopes or simply offers high security partition walls. The system has both internal and external
applications.
Securiclad Typical Applications:
Securiclad is ideal for use in:







Data centres and server rooms
Utilities infrastructure
Healthcare facilities
Cargo areas
Financial institutions
Retail sites
Private residences
Further information can be found on the Securiclad website or by contacting Sales:
Website:
www.securiclad.co.uk
Tel:
0191 2585052
Email:
[email protected]
LPS 1175:
LPCB Overview
LPCB (Loss Prevention Certification Board) have been setting the standards for loss prevention since the 1800’s
and its standards and approvals are recognised worldwide. The recognition is testimony to the extremely
thorough technical evaluation work and rigorous quality audit process undertaken by the LPCB to ensure the
security products it tests and approves deliver the proven levels of protection.
The LPCB works closely with the government, police, insurers, risk consultants and architects to develop the
standards and approval schemes which ensure security equipment and services deliver the levels of
performance required to protect against criminal and terrorist threats.
Approval to LPCB’s Loss Prevention Standards (LPSs) is specified across multiple sectors, including: education,
finance, healthcare, manufacturing, the public sector, residential, retails and utilities. The standards are also
specified for the protection of critical infrastructure where delivery of specified levels of security performance
is critical.
LPS 1175
LPS 1175 covers a broad scope of physical security products and services of any publicly available standard in
the world. LPS 1175 has been developed over many years by the LPCB, Government, Insurers and Police, and
has rapidly become a core element of physical security specification across many sectors. This standard
consists of a number of security ratings with test requirements of ascending intensity. These are measured in
terms of attack tools and time available to the attacker, and enables specifiers to select products according to
the risks that they and their property face. LPS 1175 can be used in a range of applications, from residential to
critical infrastructure projects.
Security
Rating
SR8
SR7
SR6
SR5
SR4
SR3
SR2
SR1
Maximum
Work Time
(min)
20
10
10
10
10
5
3
1
Maximum Test
Duration (min)
60
30
30
30
30
20
15
10
Domestic








Typical Applications
Commercial
Government
HIGH RISK
















LOW RISK
SR8: Products certified to this standard provide 20 minutes of resistance to extreme means of forced entry
into high value storage areas, with the use of a wide range of tools including mains powered tools.
SR7: Products certified to this standard provide 10 minutes of resistance to professional means of forced entry
into higher value storage areas, with the use of a wide range of tools including mains powered tools.
SR6: Products certified to this standard provide 10 minutes of resistance to professional means of forced entry
into higher value storage areas, with the use of a wide range of tools including mains powered tools.
SR5: Products certified to this standard provide 10 minutes of resistance to experienced attempts at forced
entry using a wide range of tools including battery powered tools. (E.g. SR4 tools plus circular saw and the
750W reciprocating saw with specialist blades.)
SR4: Products certified to this standard provide 10 minutes of resistance to experienced attempts at forced
entry using a wide range of tools including battery powered tools. (E.g. SR3 tools plus felling axe,
sledgehammer, steel wedges, disc grinder, jigsaw, etc.)
SR3: Products certified to this standard provide 5 minutes of resistance to experienced attempts at forced
entry using a wide range of tools, using a range of techniques including those that involved the creation of
noise. (E.g. SR2 tools plus short axe, chisels, crowbar gas torch, etc.)
SR2: Products certified to this standard provide 3 minutes of resistance to a determined attack by an
opportunist burglar using a range of techniques including those that involved the creation of noise. (E.g. SR1
tools plus bolt cutters, claw hammer, drill, etc.)
SR1: Products certified to this standard provide the minimal level of security, 1 minute of resistance to
opportunist attempts at entry, using a range of techniques including those that involve the creation of noise,
as well as attacks involving breaking glass. (E.g. screwdriver, knife, pliers, etc.)
Manufacturing Approval
This installation guide for the Securiclad panel system has been designed to help and advise installation teams
on the requirements to attain an approved system to LPS1175.
There are clear and defined instructions along with diagrams which need to be followed during the build
process, all associated ancillaries and fixings must also be supplied by Securiclad to ensure a completed system
is approved under the LPCB Scope. Any variation from this scope will invalidate certification.
In addition, apertures within the walling system or enclosure should only be filled with products that are
approved for use on the Securiclad system and listed on LPCB Certificate 142c & 142d and
www.redbooklive.com.
Please contact Securiclad office for additional information required.
Contact Details: Carl Lowson
Manufacturing Manager
Tel:
0191 2585052
Email:
[email protected]
Securiclad SR2, SR3 & SR4 Installation Guide
This manual contains all construction details for Securiclad: The high security composite wall panel system, achieving LPS1175
SR2, SR3 and SR4 rating for internal and external applications. The details provided in this manual are applicable to a standard
set-up. Should you require site specific installation, we can provide full technical assistance to support your requirements.
Securiclad Fire Ratings:




Manufactured to an ISO 9001:2008 quality assurance systems. Certificate Number 142.
Fire rating explained:o The panels themselves are rated up to 4 hours as tested to LPS1208 and accessed to BS476 Part 22 –
Certificate Number 142a.
Fire Rated Enclosures up to 2 hours
o This can be achieved by intumescent coating of all exposed hot rolled steel components such as corner posts,
intermediated, ‘Goal-Post’ arrangements (Price on application)
Fire Rated Enclosures from 2 up to 4 hours
o This is a site specific action with all exposed steel work requiring protection using appropriate fire boards, the
thickness of the board would depend on the required fire rating.
Internal/External Vertical/Horizontal Panels
1.
2.
3.
4.
5.
6.
7.
Ensure floor is level. The site is marked out using chalk line.
Position and fix corner posts if applicable.
Offer panel to channel and slide into position. Ensure panel is plumb before fixing.
Repeat step 3 until wall is complete, then fix securely.
Drill and fix channel 90° corner or abutments as step 2.
See construction details/drawings for additional information.
Horizontal panel construction requires 130mm long high tensile Dome Head Bolt and Temper Nut at max 600mm
centres as detailed.
Ceiling

Ensure attack face of panel is on the external side of room.



Fix and secure as construction detail
Ceiling Support
When installed Securiclad ceiling panels offer a limited walk-on facility, however this is suitable for intermittent
personnel use only, and panels should not be used as a working platform.

Overloading should be avoided at any time and personnel should not gather in groups greater than two on any single
panel, particularly adjacent to apertures, which must be suitably framed and supported.

Jumping and bouncing should be also avoided.

In areas subject to frequent use and access areas, Youngman type boards and catwalks should be used as walkways.

Ancillary equipment i.e. pipes, refrigeration equipment, ductwork, etc. should not be supported by the panels; the
support should be taken from the building structure. Installation of equipment is not allowed on unprotected panels.

The need for additional ceiling support for fire rated installations should be discussed with securiclad prior to
installation.

Note: Fire rated installations must be completed by using a bead of ‘Envirograph 62’ intumescent fire proof sealant
applied to the female joint prior to the installation and sealed with a further dead on both faces.

Note: Ceiling to ceiling panel joints are identical to the wall the wall panel flush joints.
Maintenance
Walls can be washed down with fresh water from a hose or bucket. A solution of fresh water and Tepol, or similar non
aggressive detergent, which contains dilute ammonia, may be used to remove heavy deposits from walls, followed by a fresh
water rinse.
Water temperatures should not exceed 60°, with a maximum of 100lbs per square inch.
Stubborn oil or grease stains can be easily removed with white spirit on a soft cloth, followed by an immediate fresh water rinse.
Solvents, cleaners containing abrasives and cleaners in strong concentrations should not be used. Over-cleaning or scrubbing
can be detrimental to the panel surface.
To facilitate cleaning of panels, it is important that the installation of the panel system should prevent moisture collecting in
crevices and joints. This is particularly important at the bottom of the wall panels, where pollutants from cleaning solutions of
from floor soil can cause corrosion problems. This can be achieved by a design which ensures that the edges are folded back and
by sealing the edges with a neutral curing silicone sealant.
Health and Safety
Ensure panels are lifted into place with the correct equipment as they weigh up to 70kg/m². The use of Cool Boy or Oktopus
equipment is advisable for installation.
100mm
125mm
150mm
SR2 Panel Wall
32 kg/m²
35 kg/m²
38 kg/m²
SR3 Panel Wall
38 kg/m²
41 kg/m²
44 kg/m²
SR4 Panel Wall
54 kg/m²
57 kg/m²
60 kg/m²
SR3 Re-enforced Panel* Wall
54 kg/m²
57 kg/m²
60 kg/m²
SR4 Re-enforced Panel* Wall
70 kg/m²
73 kg/m²
76 kg/m²
SR2 Panel Ceiling
32 kg/m²
35 kg/m²
38 kg/m²
SR3 Panel Ceiling
44 kg/m²
47 kg/m²
50 kg/m²
SR4 Panel Ceiling
61 kg/m²
64 kg/m²
67 kg/m²
*For use around Door area if Non Key/Key locking mechanism is used. Location of this panel type is to be no less than 1200mm
radius from the locking mechanism.
Under normal conditions the core within the security panel is stable and is not classified as carcinogenic. However, the core can
be classed as an irritant and direct contact can cause an effect to the skin known as mechanical irritation. Gloves and general
PPE should be worn. Cutting may cause dust which may also act as an irritant. General PPE should be worn. Materials used in
manufacture are classed as non-hazardous.
Structural
For site specific questions and the latest information please refer to Securiclad directly.
Walls
Span details (all measurements in mm) –
SR2
SR3
SR4
SR3 Re-enforcement Panel
SR4 Re-enforcement Panel
SR4 Double Skin Wall
2000 min to 5500 max
2000 min to 5500 max
2000 min to 5500 max
2000 min to 5500 max
2000 min to 5500 max
2000 min to 4500 max
Ceilings
Span details (all measurements in mm) –
SR2
SR3
SR4
SR3 Re-enforcement Panel
SR4 Re-enforcement Panel
2000 min to 5500 max
2000 min to 3000 max**
2000 min to 3000 max**
2000 min to 3000 max**
2000 min to 3000 max**
** Spans can be increased to 5500 with the inclusion of a top hat within the ceiling panel.
When installed Securiclad ceiling panels offer a limited walk-on facility, however this is suitable for intermittent personnel use
only, and panels should not be used as a working platform. Overloading should be avoided at any time and personnel should not
gather in groups greater than two on any single panel, particularly adjacent to apertures which must be suitably framed and
supported. Jumping and bouncing should be also avoided. In areas subject to frequent use and access areas, Youngman type
boards and catwalks should be used as walkways. Ancillary equipment i.e. pipes, refrigeration equipment, ductwork, etc. should
not be supported by the panels; the support should be taken from the building structure. Installation of equipment is not
allowed on unprotected panels.
Fixings
Face fixing services e.g. air, surface mounted electrics, push pads, and security sensors can be fixed directly to the panel face.
Heavier goods will need to be referred back to Securiclad to advise on project specific queries.
Acoustic
See data sheet from Rockwool.
Material Specifications for the Manufacture of Securiclad Security Panels
PIR – Polyisocyanurate Foam
Mineral Wool – Rockwool Conrock 12
Siderise – 38mm Thick NXR Lamella Board
Plywood – Redwood ply or OSB
Galvanised Steel – G275 Hot Dipped
Inner Skin – 0.5mm White Food Safe Laminate (WFSL)
Outer Skin – 0.5mm WFSL or Plastisol Coated Steel
Securiclad Panels:
SR2
Securiclad SR2 is an alternative panel configuration to the standard Securiclad panel. The reduction of anticutting material to the SR2 level allows the panel to maintain the strength and durability and is designed for
less critical security areas. E.g. Domestic risks 1 & 2 and Minor Commercial risks 2.
Apertures within the walling system/enclosure should only be filled with products which are approved for use
with the Securiclad System.
Products that are approved for use on the Securiclad security panel system are listed on LPCB certification and
www.redbooklive.com
This SR2 option must be installed in accordance to the SR4 instructions using all the fixings and accessories as
described within this manual with the expectations of door sets, refer to LPCB Certificate 142c & 142d.
SR 3 & 4
Securiclad have introduced a number of product upgrades to create a range of panel options. They are all
designed to enhance protection but each has a very unique attribute specific to environment and installation
requirements.
‘Securiclad Core’ is an alternative panel configuration to the standard Securiclad panel. The SR3 and SR4 anticutting material is sandwiched between Mineral Wool/PIR, in the middle of the panel. This combination makes
for a more aesthetically pleasing panel finish yet greater strength and durability of the panel.
SECTION
2
PANEL DETAILS
ATTACK FACE
0.5/0.7 STEEL SHEET
PIR/MINERAL WOOL CORE
5
ANTI-CUTTING
MATERIAL
DIM 'X'
18
ENLARGED DETAIL
SCALE 1:1
PIR/MINERAL WOOL CORE
0.5/0.7 STEEL SHEET
SR2 PANEL JOINT DETAIL - WALL
SCALE 1:1
SPS100/125/150
CONFIGURATION
SPLINE
SR2 WALL PANEL
WIDTH (mm)
HEIGHT/LENGTH (mm)
THICKNESS (mm) (DIM 'X')
MIN
MAX
MIN
MAX
SPS 100
SPS 125
SPS 150
250
1190*
2000
5500
100
125
150
* NOTE: ALL PANELS CAN BE PROVIDED IN EITHER 900mm OR 1190mm WIDE INCORPORATING
MALE AND FEMALE JOINTS. PANEL WIDTH LESS THAN 900mm, DOWN TO A MINIMUM OF 250mm
CAN BE PROVIDED BUT WILL ONLY INCORPORATE A MALE OR FEMALE JOINT WITH THE
OPPOSITE BEING A STRAIGHT CUT.
Securiclad
SCALE 1:2
ATTACK FACE
0.5/0.7 STEEL SHEET
DIM 'X'
5
ANTI-CUTTING
MATERIAL
PIR/MINERAL WOOL CORE
18
ENLARGED DETAIL
SCALE 1:1
ANTI-CUTTING
MATERIAL
SR2 PANEL JOINT DETAIL - CEILING
SCALE 1:1
0.5/0.7 STEEL SHEET
SPS100/125/150
CONFIGURATION
SPLINE
SR2 CEILING PANEL
WIDTH (mm)
HEIGHT/LENGTH (mm)
THICKNESS (mm) (DIM 'X')
MIN
MAX
MIN
MAX
SPS 100
SPS 125
250
1190*
2000
5500
100
125
SPS 150
150
* NOTE: ALL PANELS CAN BE PROVIDED IN EITHER 900mm OR 1190mm WIDE INCORPORATING
MALE AND FEMALE JOINTS. PANEL WIDTH LESS THAN 900mm, DOWN TO A MINIMUM OF 250mm
CAN BE PROVIDED BUT WILL ONLY INCORPORATE A MALE OR FEMALE JOINT WITH THE
OPPOSITE BEING A STRAIGHT CUT.
Securiclad
SCALE 1:2
ATTACK FACE
0.5/0.7 STEEL SHEET
5
PIR/MINERAL WOOL CORE
DIM 'X'
ANTI-CUTTING
MATERIAL
18
ENLARGED DETAIL
SCALE 1:1
PIR/MINERAL WOOL CORE
0.5/0.7 STEEL SHEET
SR3 PANEL JOINT DETAIL - WALL
SCALE 1:1
SPS100/125/150
SPLINE
CONFIGURATION
SR3 WALL PANEL
WIDTH (mm)
HEIGHT/LENGTH (mm)
THICKNESS (mm)(DIM 'X')
MIN
MAX
MIN
MAX
SPS 100
SPS 125
SPS 150
250
1190*
2000
5500
100
125
150
* NOTE: ALL PANELS CAN BE PROVIDED IN EITHER 900mm OR 1190mm WIDE INCORPORATING
MALE AND FEMALE JOINTS. PANEL WIDTH LESS THAN 900mm, DOWN TO A MINIMUM OF 250mm
CAN BE PROVIDED BUT WILL ONLY INCORPORATE A MALE OR FEMALE JOINT WITH THE
OPPOSITE BEING A STRAIGHT CUT.
Securiclad
SCALE 1:2
0.5/0.7 STEEL SHEET
ATTACK FACE
5
ANTI-CUTTING
MATERIAL
DIM 'X'
PIR/MINERAL WOOL CORE
18
ENLARGED DETAIL
SCALE 1:1
ANTI-CUTTING
MATERIAL
SR3 PANEL JOINT DETAIL - CEILING
SCALE 1:1
0.5/0.7 STEEL SHEET
SPS100/125/150
SPLINE
CONFIGURATION
SR3 CEILING PANEL
WIDTH (mm)
HEIGHT/LENGTH (mm)
THICKNESS (mm) (DIM 'X')
MIN
MAX
MIN
MAX
SPS 100
SPS 125
SPS 150
250
1190*
2000
3000
100
125
150
* NOTE: ALL PANELS CAN BE PROVIDED IN EITHER 900mm OR 1190mm WIDE INCORPORATING
MALE AND FEMALE JOINTS. PANEL WIDTH LESS THAN 900mm, DOWN TO A MINIMUM OF 250mm
CAN BE PROVIDED BUT WILL ONLY INCORPORATE A MALE OR FEMALE JOINT WITH THE
OPPOSITE BEING A STRAIGHT CUT.
Securiclad
SCALE 1:2
ATTACK FACE
0.5/0.7 STEEL SHEET
5
PIR/MINERAL WOOL CORE
DIM 'X'
18
ANTI-CUTTING
MATERIAL
ENLARGED DETAIL
SCALE 1:1
PIR/MINERAL WOOL CORE
0.5/0.7 STEEL SHEET
SR4 PANEL JOINT DETAIL - WALL
SCALE 1:1
SPS100/125/150
CONFIGURATION
SPLINE
SR4 WALL PANEL
WIDTH (mm)
HEIGHT/LENGTH (mm)
THICKNESS (mm) (DIM 'X')
MIN
MAX
MIN
MAX
SPS 100
SPS 125
250
1190*
2000
5500
100
125
SPS 150
150
* NOTE: ALL PANELS CAN BE PROVIDED IN EITHER 900mm OR 1190mm WIDE INCORPORATING
MALE AND FEMALE JOINTS. PANEL WIDTH LESS THAN 900mm, DOWN TO A MINIMUM OF 250mm
CAN BE PROVIDED BUT WILL ONLY INCORPORATE A MALE OR FEMALE JOINT WITH THE
OPPOSITE BEING A STRAIGHT CUT.
SCALE 1:2
Securiclad
ATTACK FACE
5
0.5/0.7 STEEL SHEET
PIR/MINERAL WOOL CORE
ANTI-CUTTING
MATERIAL
18
DIM 'X'
ANTI-CUTTING
MATERIAL
ENLARGED DETAIL
SCALE 1:1
ANTI-CUTTING
MATERIAL
0.5/0.7 STEEL SHEET
SR4 PANEL JOINT DETAIL - CEILING
SCALE 1:1
SPLINE
SPS100/125/150
CONFIGURATION
SR4 CEILING PANEL
WIDTH (mm)
HEIGHT/LENGTH (mm)
THICKNESS (mm) (DIM 'X')
MIN
MAX
MIN
MAX
SPS 100
SPS 125
SPS 150
250
1190*
2000
3000
100
125
150
* NOTE: ALL PANELS CAN BE PROVIDED IN EITHER 900mm OR 1190mm WIDE INCORPORATING
MALE AND FEMALE JOINTS. PANEL WIDTH LESS THAN 900mm, DOWN TO A MINIMUM OF 250mm
CAN BE PROVIDED BUT WILL ONLY INCORPORATE A MALE OR FEMALE JOINT WITH THE
OPPOSITE BEING A STRAIGHT CUT.
SCALE 1:2
Securiclad
0.5mm STEEL SHEET
38mm PIR/MINERAL WOOL
5
ANTI-CUTTING
MATERIAL
0.5mm STEEL SHEET
18
0.5mm STEEL SHEET
ENLARGED DETAIL
SCALE 1:1
ANTI-CUTTING
MATERIAL
38mm PIR/MINERAL WOOL
0.5mm STEEL SHEET
SR4 DOUBLE SKIN DETAIL - WALL
SCALE 1:1
250mm MIN STAGGER
DPS50
CONFIGURATION
SR4 WALL PANEL
SR4 DOUBLE SKIN JOINT DETAIL - WALL
SCALE 1:2
WIDTH (mm)
HEIGHT/LENGTH (mm)
OVERALL WALL
THICKNESS (mm)
MIN
MAX
MIN
MAX
DPS 50
250
1190*
2000
4500
100
Securiclad
0.5mm STEEL SHEET
38mm PIR/MINERAL WOOL
5
ANTI-CUTTING
MATERIAL
0.5mm STEEL SHEET
18
0.5mm STEEL SHEET
ENLARGED DETAIL
SCALE 1:1
ANTI-CUTTING
MATERIAL
38mm PIR/MINERAL WOOL
0.5mm STEEL SHEET
SR4 DOUBLE SKIN DETAIL - CEILING
SCALE 1:1
250 mm MIN STAGGER
DPS50
CONFIGURATION
SR4 CEILING PANEL
SR4 DOUBLE SKIN JOINT DETAIL - CEILING
SCALE 1:2
WIDTH (mm)
HEIGHT/LENGTH (mm)
OVERALL WALL
THICKNESS (mm)
MIN
MAX
MIN
MAX
DPS 50
250
1190*
2000
3000
100
Securiclad
SPLINE
MINERAL WOOL
76 (SPS 100), 101 (SPS 125)
OR 126 (SPS 150)
ATTACK FACE
25
ANTI-CUTTING
MATERIAL
MECHANICAL FIXING
5.5x16mm SELF DRILL/TAP
@ 600mm CENTRES
OUTER STEEL FACE
BONDED
2 THK
GALV
MECHANICAL FIXING 4.8x19mm
PRO LOW PROFILE PAN HEAD
SELF DRILLING SCREW @
600mm CENTRES
SPLINE
MINERAL WOOL
BONDED
ANTI-CUTTING
MATERIAL
FILL WITH MINERAL
WOOL 70x70mm
FIRE-STOP 12
74
INNER STEEL FACE
SR3 CEILING SPAN 3000-5500mm
Securiclad
CONFIGURATION
SR3 CEILING PANEL
WIDTH (mm)
MIN
250
SPS100/125/150 WITH TOP HAT
HEIGHT/LENGTH (mm)
MAX
1190*
MIN
3000
MAX
5500
THICKNESS (mm) (DIM 'X')
SPS 100
100
SPS 125
125
SPS 150
150
* NOTE: ALL PANELS CAN BE PROVIDED IN EITHER 900mm OR 1190mm WIDE INCORPORATING
MALE AND FEMALE JOINTS. PANEL WIDTH LESS THAN 900mm, DOWN TO A MINIMUM OF 250mm
CAN BE PROVIDED BUT WILL ONLY INCORPORATE A MALE OR FEMALE JOINT WITH THE OPPOSITE
BEING A STRAIGHT CUT.
ANTI-CUTTING
MATERIAL
DIM 'X'
ATTACK FACE
ANTI-CUTTING
MATERIAL
SR4 CEILING SPAN 3000-5500mm
Securiclad
Reinforcement Panel Configuration
SR3 & SR4
The Securiclad SR3/SR4 Reinforcement Panel is specifically designed for use when a non-key/key door
mechanism is chosen within the system. The additional anti cutting material layers are specific arranged to
significantly increase the panel’s security around the door sets within a 1200mm radius.
Note: The Reinforcement Panel must be installed in accordance to the SR4 installation Guide using all fixings
and accessories as describes within the installation guidance using all the fixings and accessories as described
within the manual with the exceptions of the door sets. Refer to LPCB Certificate 142c & 142d.
ATTACK FACE
0.5/0.7 STEEL SHEET
PIR/MINERAL WOOL CORE
5
ANTI-CUTTING
MATERIAL
DIM 'X'
18
ENLARGED DETAIL
SCALE 1:1
PIR/MINERAL WOOL CORE
0.5/0.7 STEEL SHEET
SR3 RE-ENFORCEMENT PANEL JOINT DETAIL - WALL
SCALE 1:1
SPSCORE 100/125/150
SPLINE
CONFIGURATION
SR3 RE-ENF PANEL
WIDTH (mm)
HEIGHT/LENGTH (mm)
MIN
MAX
MIN
250
1190*
2000
MAX
5500
THICKNESS (mm) (DIM 'X')
SPS 100
SPS 125
SPS 150
100
125
150
* NOTE: ALL PANELS CAN BE PROVIDED IN EITHER 900mm OR 1190mm WIDE INCORPORATING
MALE AND FEMALE JOINTS. PANEL WIDTH LESS THAN 900mm, DOWN TO A MINIMUM OF 250mm
CAN BE PROVIDED BUT WILL ONLY INCORPORATE A MALE OR FEMALE JOINT WITH THE
OPPOSITE BEING A STRAIGHT CUT.
SCALE 1:2
Securiclad
ATTACK FACE
5
0.5/0.7 STEEL SHEET
ANTI-CUTTING
MATERIAL
18
DIM 'X'
ENLARGED DETAIL
SCALE 1:1
PIR/MINERAL WOOL CORE
ANTI-CUTTING
MATERIAL
0.5/0.7 STEEL SHEET
SR3 RE-ENFORCEMENT PANEL JOINT DETAIL - CEILING
SCALE 1:1
SPS 100/125/150
SPLINE
CONFIGURATION
SR3 RE-ENFORCED
CEILING PANEL
WIDTH (mm)
HEIGHT/LENGTH (mm)
THICKNESS (mm) (DIM 'X')
MIN
MAX
MIN
MAX
SPS 100
SPS 125
SPS 150
250
1190*
2000
5500
100
125
150
* NOTE: ALL PANELS CAN BE PROVIDED IN EITHER 900mm OR 1190mm WIDE INCORPORATING
MALE AND FEMALE JOINTS. PANEL WIDTH LESS THAN 900mm, DOWN TO A MINIMUM OF 250mm
CAN BE PROVIDED BUT WILL ONLY INCORPORATE A MALE OR FEMALE JOINT WITH THE
OPPOSITE BEING A STRAIGHT CUT.
SCALE 1:2
Securiclad
ATTACK FACE
0.5/0.7 STEEL SHEET
PIR/MINERAL WOOL CORE
DIM 'X'
5
ANTI-CUTTING
MATERIAL
18
ENLARGED DETAIL
SCALE 1:1
PIR/MINERAL WOOL CORE
0.5/0.7 STEEL SHEET
SR4 RE-ENFORCEMENT PANEL JOINT DETAIL - WALL
SCALE 1:1
SPSCORE 100/125/150
SPLINE
CONFIGURATION
SR4 RE-ENF PANEL
WIDTH (mm)
HEIGHT/LENGTH (mm)
MIN
MAX
MIN
250
1190*
2000
MAX
5500
THICKNESS (mm) (DIM 'X')
SPS 100
SPS 125
SPS 150
100
125
150
* NOTE: ALL PANELS CAN BE PROVIDED IN EITHER 900mm OR 1190mm WIDE INCORPORATING
MALE AND FEMALE JOINTS. PANEL WIDTH LESS THAN 900mm, DOWN TO A MINIMUM OF 250mm
CAN BE PROVIDED BUT WILL ONLY INCORPORATE A MALE OR FEMALE JOINT WITH THE
OPPOSITE BEING A STRAIGHT CUT.
SCALE 1:2
Securiclad
ATTACK FACE
ANTI-CUTTING
MATERIAL
DIM 'X'
5
0.5/0.7 STEEL SHEET
PIR/MINERAL WOOL CORE
18
ENLARGED DETAIL
SCALE 1:1
ANTI-CUTTING
MATERIAL
0.5/0.7 STEEL SHEET
SR4 RE-ENFORCEMENT PANEL JOINT DETAIL - CEILING
SCALE 1:1
SPS 100/125/150
SPLINE
CONFIGURATION
SR4 RE-ENFORCED
CEILING PANEL
WIDTH (mm)
HEIGHT/LENGTH (mm)
THICKNESS (mm) (DIM 'X')
MIN
MAX
MIN
MAX
SPS 100
SPS 125
SPS 150
250
1190*
2000
5500
100
125
150
* NOTE: ALL PANELS CAN BE PROVIDED IN EITHER 900mm OR 1190mm WIDE INCORPORATING
MALE AND FEMALE JOINTS. PANEL WIDTH LESS THAN 900mm, DOWN TO A MINIMUM OF 250mm
CAN BE PROVIDED BUT WILL ONLY INCORPORATE A MALE OR FEMALE JOINT WITH THE
OPPOSITE BEING A STRAIGHT CUT.
SCALE 1:2
Securiclad
DIM 'X'
ANTI-CUTTING
MATERIAL
ANTI-CUTTING
MATERIAL
Securiclad
CONFIGURATION
SR3 CEILING PANEL
WIDTH (mm)
MIN
250
SPS100/125/150 WITH TOP HAT
HEIGHT/LENGTH (mm)
MAX
1190*
MIN
3000
MAX
5500
THICKNESS (mm) (DIM 'X')
SPS 100
100
SPS 125
125
SPS 150
150
* NOTE: ALL PANELS CAN BE PROVIDED IN EITHER 900mm OR 1190mm WIDE INCORPORATING
MALE AND FEMALE JOINTS. PANEL WIDTH LESS THAN 900mm, DOWN TO A MINIMUM OF 250mm
CAN BE PROVIDED BUT WILL ONLY INCORPORATE A MALE OR FEMALE JOINT WITH THE OPPOSITE
BEING A STRAIGHT CUT.
ANTI-CUTTING
MATERIAL
DIM 'X'
ATTACK FACE
ANTI-CUTTING
MATERIAL
Securiclad
SECTION
3
WALL DETAILS
FULL PANEL
F16 AT 600mm
CENTRES MAX.
STAGGERED
NOTE:
GALVANISED STEEL ANGLES SUPPLIED IN MAX
3000mm LENGTHS AND SHOULD BE CUT TO SUIT
INSTALLATION HEIGHT. WHEN WALL IS GREATER
THAN 3000mm CUT STEEL ANGLES TO MATCH
HEIGHT OF WALL. MINIMUM ANGLE LENGTH TO BE
1000mm & INCLUDE A MINIMUM OF 2 No. FIXINGS
FULL PANEL
A10
FULL PANELS INTO CORNER POSTS TO BE
FIXED USING F16 TAMPER FIXINGS .
Securiclad
FULL PANEL INTO CORNER POST
NARROW PANEL
F12 AT 600mm CENTRES
MAX. STAGGERED
NARROW PANELS INTO CORNER POSTS TO BE
FIXED USING F12 BOLTED FIXINGS.
ATTACK FACE
NOTE:
GALVANISED STEEL ANGLES SUPPLIED IN MAX
3000mm LENGTHS AND SHOULD BE CUT TO SUIT
INSTALLATION HEIGHT. WHEN WALL IS GREATER
THAN 3000mm CUT STEEL ANGLES TO MATCH
HEIGHT OF WALL. MINIMUM ANGLE LENGTH TO BE
1000mm & INCLUDE A MINIMUM OF 2 No. FIXINGS
NARROW PANEL
A10
Securiclad
NARROW PANEL INTO CORNER POST
F14 FIXINGS AT 600mm
MAX CENTRES INTO
EXISTING CEILING
EXISTING CEILING
A12
F16 FIXINGS AT 600mm
MAX CENTRES
F15 FIXING TO EXISTING
WALL
A10
WALL PANEL
EXISTING WALL.
CONCRETE OR
BRICK/BLOCKWORK
ATTACK FACE
A12
EXISTING WALL.
CONCRETE OR
BRICK/BLOCKWORK
F16 FIXINGS AT 600mm
MAX CENTRES
A10
Securiclad
F15 FIXINGS AT 600mm
MAX CENTRES INTO
EXISTING FLOOR
PARTITION WALL - BASE ANGLES
A12
F16 FIXINGS AT 600mm
MAX CENTRES
A10
WALL PANEL
EXISTING WALL.
PLYWOOD OR SOFTWALL
ATTACK FACE
EXISTING WALL.
PLYWOOD OR SOFTWALL
F16 FIXINGS AT 600mm
MAX CENTRES
C10
Securiclad
F15 FIXINGS AT 600mm
MAX CENTRES INTO
EXISTING FLOOR
PARTITION WALL - BASE CHANNEL
EXISTING CEILING
P1
ATTACK FACE
A12
F16 FIXINGS AT 600mm
MAX CENTRES
F16 FIXINGS AT 600mm
MAX CENTRES
A10
SECTION 'A-A'
FULL PANELS INTO CORNER POST
Securiclad
EXISTING CEILING
A12
NARROW PANELS
INTO CORNER POSTS
TO BE FIXED USING F12
BOLTED FIXINGS.
NARROW
PANEL
ATTACK FACE
A10
NARROW
PANEL
A10
F12 AT
600mm
CENTRES
MAX.
STAGGERED
SECTION 'A-A'
NARROW PANELS INTO CORNER POST
Securiclad
SECTION
4
CEILING DETAILS
A11
A10
NOTE:
GALVANISED STEEL ANGLES SUPPLIED IN MAX
3000mm LENGTHS AND SHOULD BE CUT TO SUIT
INSTALLATION HEIGHT. WHEN WALL IS GREATER
THAN 3000mm CUT STEEL ANGLES TO MATCH
HEIGHT OF WALL. MINIMUM ANGLE LENGTH TO BE
1000mm & INCLUDE A MINIMUM OF 2 No. FIXINGS
Securiclad
WALL TO CEILING DETAIL
ATTACK FACE
CEILING PANEL
SR CORE
A10
A10
P2
(OPTIONAL)
WALL PANEL
P2
(OPTIONAL)
Securiclad
ATTACK FACE
CEILING PANEL
SR CORE
A10
P2
(OPTIONAL)
WALL PANEL
SR CORE
P2
(OPTIONAL)
A10
Securiclad
0.5mm THICK
STEEL DECORATIVE
FLASHING
STEELWORK (I BEAM)
BY OTHERS
2mm GALVANIZED
COVER STRIP
NOTE:
A MINIMUM OF THREE FIXINGS
MUST USED
Securiclad
SECTION
5
FLOOR DETAILS
WALL PANEL
ATTACK FACE
F16 FIXINGS AT 600mm
MAX CENTRES
C10
Securiclad
F15 FIXINGS AT 600mm
MAX CENTRES INTO
EXISTING FLOOR
SECURICLAD WALL/FLOOR FIXING
ATTACK FACE
C10 (WPC)
F15 FIXINGS AT 600mm
MAX CENTRES
Securiclad
RAISED BASE DETAIL WITH DRIP
THERMAL BREAK
ATTACK FACE
WALL PANEL
FLASHING FIXED WITH STRUCTURAL
BONDING TAPE (NOT SHOWN) OR
MECHANICALLY FIXEDLE
INTERNAL CONCRETE
FLOOR FINISH
FLOOR
INSULATION
C10 (WPC)
COVER CLOSER FLASHING
(OPTIONAL) COLOUR TO
MATCH PANEL
F12 FIXINGS AT 600mm
MAX CENTRES
DAMP PROOF
MEMBRANE(DPM)
F15 FIXINGS AT 600mm
MAX CENTRES
Securiclad
BASE FIXING DETAIL
WALL PANEL
C10
Securiclad
F15 FIXINGS AT 600mm
MAX CENTRES INTO
EXISTING FLOOR
SECTION
JOINTS
6
MIN 250mm
NOTE:
GALVANISED STEEL ANGLES
SUPPLIED IN MAX 3000mm
LENGTHS AND SHOULD BE CUT
TO SUIT INSTALLATION. WHEN
WALL IS GREATER THAN 3000mm
CUT STEEL ANGLES TO MATCH
LENGTH OF WALL
A MINIMUM OF THREE F12 BLOTS
MUST BE USED IN HEADER U
CHANNEL MAX 600mm CENTRES
NOTE:
WHEN PANELS SPAN HORIZONTALLY
THE TOP-MOST PANEL MUST BE A
MINIMUM OF 250 WIDE. ANY PANEL
LESS THAN FULL WIDTH MUST HAVE
A MINIMUM OF 3 No. F12 BOLTS IN
THE JOINT BETWEEN IT AND THE
ADJACENT PANEL.
ATTACK FACE
Securiclad
HORIZONTAL WALL JOINT
NOTE:
WHEN FIXING TO BRICKWORK OR
CONCRETE USE F15, MAX 600mm
CENTRES VIA 13mm DIAMETER
HOLES.
WHEN FIXING TO STEELWORK
USE F11, MAX 600mm CENTRES.
Securiclad
NOTE:
WHEN FIXING TO BRICKWORK OR
CONCRETE USE F15, MAX 600mm
CENTRES VIA 13mm DIAMETER
HOLES.
WHEN FIXING TO STEELWORK
USE F11, MAX 600mm CENTRES.
Securiclad
F11 FIXINGS AT 600mm
MAX CENTRES
F11 FIXINGS AT 600mm
MAX CENTRES
F16 FIXINGS AT 600mm
MAX CENTRES
C10
A10
PANEL
PANEL
Securiclad
'A'
EXTERNAL ANGLE
250 mm
MINIMUM
NOTE: WHERE A DOOR HEADER
PANEL IS REQUIRED A MINIMUM
OF 3 No. F12 BOLTED FIXINGS
MUST BE USED AT THE TOP AND
BOTTOM OF THE HEADER PANEL
HEADER
PANEL
HEADER PANEL MUST BE A
MINIMUM OF 250mm IN LENGTH
ATTACK
FACE
'A'
PANEL
180x180
EXTERNAL
ANGLE
DOOR
CEILING PANEL
PANEL
WALL PANEL
250mm
MINIMUM
70x70 INTERNAL
ANGLE
C11/C13
DOOR
CHANNEL
TOP OF DOOR
FRAME
F12 FIXING. 3 No.
MIN
ATTACK FACE
F12 FIXING. 3 No.
MIN
SECTION 'A-A'
VERTICAL WALL JOINT WITH HEADER PANEL
Securiclad
PANEL
PANEL
PANEL
250
MIN
NOTE: MINIMUM OF 3 No. F12
BOLTED FIXINGS MUST BE USED
'A'
180x180
EXTERNAL
ANGLE
ATTACK
FACE
'A'
CEILING PANEL
DOOR
WALL PANEL
250mm
MINIMUM
70x70 INTERNAL
ANGLE
C11/C13
DOOR
CHANNEL
TOP OF DOOR
FRAME
F12 FIXING. 3 No.
MIN
SECTION 'A-A'
ATTACK FACE
WHERE A PANEL IS CUT TO
ACCOMODATE A DOOR FRAME
A MINIMUM OF 250mm MUST
REMAIN
250
MIN
250
MIN
VERTICAL WALL JOINT - NO HEADER PANEL
Securiclad
SECTION
7
PENETRATIONS
Aperture Construction and Approved Products
Apertures within the walling and ceiling system or enclosure should only be filled with products that are
approved for use on the Securiclad system and listed on LPCB Certificate 142c & 142d and
www.redbooklive.com.
PENETRATION CANNOT BE LESS THAN 150mm FROM THE TOP/BOTTOM OR SIDE OF THE PANEL AND NOT
LESS THAN 75mm FROM ANOTHER PENETRATION IN ANY DIRECTION FOR SR2 & SR3 ONLY, FOR SR4
DIMENSIONS ARE 250mm & 150mm RESPECTIVELY.
)
R3
MIN 30mm
ELEVATION ON PANEL
SCALE 1:7.5
PANEL
COLLAR
ZmmØ
150 MIN
mØ
Xm
150 MIN
N
MI
5 No. EQUALLY SPACED 17
Ø BOLT HOLES ON 130mm
PCD
YmmØ
75
TO
MIN 30mm
SR
N(
IO
AT
TR R4
E
PEN R S
ER m FO
H
OT m
AN 150
S
2&
COLLAR
Ymm Ø
FRONT ELEVATION
SCALE 1:2
6
SECTION THROUGH
SCALE 1:2
MATERIAL: ZmmØ MILD STEEL TUBE x 3mm (POWDER COATED TO SUIT)
YmmØ X 6mm THICK PLATE WITH XmmØ HOLE
NUMBER REQUIRED PER INSTALLATIOn: 2No (ONE EACH SIDE OF THE PANEL)
FIXINGS: 5 No. F12 FIXINGS
SECTION THROUGH PANEL
SCALE 1:5
Securiclad
200
20
2
300
SIDE ELEVATION
SCALE 1:2
FRONT ELEVATION
SCALE 1:2
MATERIAL: 300mm x 200mm x 2mm THICK GALV PLATE (POWDER COATS TO SUIT)
NUMBER REQUIRED PER INSTALLATION: 2No ( ONE EACH SIDE OF PANEL)
FIXINGS: 4 No. F12 FIXINGS
150 mm
MIN (SR4)
40
20
90
75mm
MIN (SR2 & SR3)
55
110
200
55
250mm
MIN (SR4)
SECURICLAD PANEL
8 No. 50mm Ø HOLES
150mm
MIN (SR2 & SR3)
4 No. 15.5mm Ø HOLES
150mm
MIN (SR2 & SR3)
250mm
MIN (SR4)
ELEVATION ON PANEL
SCALE 1:10
Securiclad
NOTE:
PENETRATION 'A' CANNOT BE LESS THAN 150mm FROM THE TOP/BOTTOM OR SIDE OF THE
PANEL AND NOT LESS THAN 75mm FROM ANOTHER PENETRATION IN ANY DIRECTION FOR SR2
& SR3 ONLY, FOR SR4 DIMENSIONS ARE 250mm & 150mm RESPECTIVELY.
PART 'A'
=
4.5mm Ø HOLE (TYP)
PART 'B'
100
100
PART 'B'
200 (PART 'B')
200
50
=
52
PART 'A'
PART 'B'
3
=
=
'TYPICAL
POSITIONS'
PART 'A'
198.5 (PART 'A')
FRONT ELEVATION
SCALE 1:2
PANEL
PENETRATION
MATERIAL: 50mm x 49mm x 3mm THICK GALV ANGLE (POWDER COATS TO SUIT)
NUMBER REQUIRED PER INSTALLATION: 2No SETS ( 2No REQUIRED PARTS 'A' AND 'B' EACH SIDE OF PANEL)
FIXINGS: 12 No. F11 FIXINGS
Securiclad
PENETRATION
SECTION THROUGH PANEL
SCALE 1:5
75
Ø
TO
20
20
250 MIN
(FOR (SR4)
75
Ø
ES
SØ
LE
HO
150mm MIN TO
150 MIN
Ø
TO
L
HO
ANOTHER PENETRATION (SR4)
75mm MIN TO
ANOTHER PENETRATION (SR2 & SR3)
(FOR SR2 & SR3)
HO
HO
LE
LE
SØ
SØ
20
20
TO
TO
75
75
Ø
Ø
NOTE:
HOLE EDGE DISTANCE CANNOT BE LESS THAN 150mm FROM THE TOP/BOTTOM OR SIDE OF THE PANEL AND
NOT LESS THAN 75mm FROM ANOTHER PENETRATION IN ANY DIRECTION FOR SR3 & SR4, FOR SR4 DIMENSIONS
ARE 250mm & 150mm RESPECTIVELY.
Securiclad
SECURICLAD PANEL
UNPROTECTED PENETRATIONS
C11
60mm X 102mm X 60 X 6mm THICK
HOT ROLLED STEEL U CHANNEL ON
THREE SIDES FOR DOORS AND FOUR
SIDES FOR WINDOWS, SECURITY
GRILLS ETC OF THE APERTURE
CORNERS TO BE MITRED.
F12 FIXINGS AT MAX
600mm CENTRES
C13
NOTE:
A MINIMUM OF THREE FIXINGS MUST BE ON
EACH SIDE OF THE FRAME SECTION
Securiclad
FRAME-OUT CHANNEL OPTIONS
SECTION
8
ASSOCIATED
SECURICLAD
COMPONENTS
70
2mm MINIMUM
GALV STEEL
70
70
3 THK
103 (INT)
2 THK
A10
C10
2mm MINIMUM
GALV STEEL
180
2mm MINIMUM
GALV STEEL
60
180
6 THK
103 (INT)
2 THK
C11
A11
100
6 THK
70
70
6 THK
103 (INT)
2 THK
A12
C13
Securiclad
X
Y
Y
Y
Y
Y
X
70
22
CUSTOMER LENGTHS
DIM X
DIM Y
DIM Z
Z
C13 CHANNEL -SIDE VIEW
SCALE 1:10
X
Y
Y
Y
Y
Y
X
Y
Y
Y
Y
X
103 INT
17 Ø HOLES
14 Ø HOLES
X
Y
C13 CHANNEL -PLAN VIEW
SCALE 1:10
35
6
100 (100)
6
6
14mm Ø HOLE
6
17mm Ø HOLE
48
22
EXTERNAL FACE
6
103
121
64
70
TYPICAL SECTION THROUGH C13 CHANNEL
6 THICK HOT ROLLED STEEL
SCALE 1:2
Securiclad
X
Y
Y
Y
Y
Y
X
60
25
CUSTOMER LENGTHS
DIM X
DIM Y
DIM Z
Z
C11 CHANNEL -SIDE VIEW
SCALE 1:10
X
Y
Y
Y
Y
Y
X
Y
Y
Y
X
103 INT
14 Ø HOLES
17 Ø HOLES
X
Y
Y
C11 CHANNEL -PLAN VIEW
SCALE 1:10
103
14mm Ø HOLE
6
60
17mm Ø HOLE
Securiclad
TYPICAL SECTION THROUGH C11 CHANNEL
6 THICK HOT ROLLED STEEL
SCALE 1:2
X
Y
Y
Y
Y
Y
X
CUSTOMER LENGTHS
DIM X
DIM Y
DIM Z
70
25
6 Ø HOLES
Z
C10 CHANNEL -SIDE VIEW
SCALE 1:10
X
Y
Y
Y
Y
Y
X
W
W
14 Ø HOLES
C10 CHANNEL -PLAN VIEW
SCALE 1:10
70
3 THK
70
103
TYPICAL SECTION THROUGH C11 CHANNEL
3 THICK GALV STEEL
SCALE 1:2
Securiclad
CUSTOMER LENGTHS
DIM Z
70
Z
A12 ANGLE
SCALE 1:10
70
100
2 THK
TYPICAL SECTION THROUGH A12 ANGLE
2 THICK GALV STEEL
SCALE 1:2
Securiclad
Z
CUSTOMER LENGTHS
DIM X
DIM Y
DIM Z
16 Ø HOLES
50
Y
Y
Y
Y
Y
50
A11 ANGLE - SIDE VIEW
SCALE 1:10
16 Ø HOLES
75
Y
Y
Y
Y
X
75
A11 ANGLE - PLAN VIEW
SCALE 1:10
Z
50
Y
Y
Y
Y
Y
50
125
℄
16 Ø HOLES
75
Y
Y
Y
DEVELOPED VIEW - MANUFACTURING ONLY
180
SCALE 1:10
180
363
125
16 Ø HOLES
TYPICAL SECTION THROUGH A11 ANGLE
2 THICK GALV STEEL
SCALE 1:5
2 THK
Y
X
75
Securiclad
CUSTOMER LENGTHS
DIM Z
70
Z
A10 ANGLE
SCALE 1:10
70
70
2 THK
TYPICAL SECTION THROUGH A10 ANGLE
2 THICK GALV STEEL
SCALE 1:2
Securiclad
6 PLT
167x6 THK PLATE
DIM 'F'
6 Ø HOLES
FOR F16 FIXINGS
167x6 THK PLATE
WELDED TO RHS
ATTACK
FACE
50
DIM 'D'
50
167
DIM 'G'
167
A
26 Ø HOLES
100 (100)
100
26
26
50
DIM 'B'
DIM 'B'
6
DIM 'B'
13 Ø HOLES
FOR F15 FIXINGS
DIM 'B'
DIM 'B'
28
14 Ø HOLES
FOR F15 FIXINGS
36
26
6
DRILL & TAP HOLE FOR
M8 (MINIMUM) BOLT
CUSTOMER DIMS
DIM A
DIM B
DIM C
DIM D
DIM E
DIM F
DIM G
100x167x10 THK
BASE PLATE
50
6
THK
DIM 'B'
DIM 'B'
DIM 'B'
ATTACK
FACE
F16
WALL
F15
DIM 'B'
DIM 'B'
75
40
10
THK
DIMS IN RHS
SECTION 'A-A'
28
167x 6 THK LOOSE PLATE
50
50
END POST - TAMPER OPTION
50
167
B
A
6 Ø HOLES
FOR F16 FIXINGS
CLEARANCE HOLE TO SUIT
BOLT SIZE THROUGH RHS
DIM 'B'
DIM 'E' (LENGTH OF 167x6 THICK PLATE - FULL HEIGHT IF NO CEILING REQUIRED)
SECTION 'B-B'
M8 BOLT
(MIN)
DIM 'B'
DIM 'B'
13 Ø HOLES
N/S FACE
26 Ø HOLES
OPP FACE
DIMS IN PLT
100x100
x6 RHS
DIM 'B'
DIM 'B'
50 50
HOLES FOR M8
(MIN) BOLTS
DRILLED AND
TAPPED THIS
FACE
40
DIMS IN RHS
DIM 'B'
DIM 'B'
DIM 'B'
6 Ø HOLES
IN PLATE
DIM 'B'
DIM 'B'
DIM 'C' (LENGTH OF 100x100x6 RHS - FULL HEIGHT IF NO CEILING REQUIRED)
50 50
B
10
THK
DIM 'A' (LENGTH OF 234x6 THICK PLATE)
167
CLEARANCE HOLES
TO SUIT BOLT SIZE
THROUGH RHS
50
LOOSE PLATE
28
LOOSE
PLATE
PLAN VIEW
F16
Securiclad
6 PLT
167x6 THK PLATE
DIM 'F'
14 Ø HOLES
FOR F12 FIXINGS
167x6 THK PLATE
WELDED TO RHS
ATTACK
FACE
50
DIM 'D'
50
167
DIM 'G'
167
A
26 Ø HOLES
100
26
26
50
DIM 'B'
100 (100)
DIM 'B'
DIM 'B'
6
13 Ø HOLES
FOR F15 FIXINGS
DIM 'B'
DIM 'B'
28
14 Ø HOLES
FOR F15 FIXINGS
36
26
6
DRILL & TAP HOLE FOR
M8 (MINIMUM) BOLT
CUSTOMER DIMS
DIM A
DIM B
DIM C
DIM D
DIM E
DIM F
DIM G
100x167x10 THK
BASE PLATE
50
6
THK
DIM 'B'
DIM 'B'
DIM 'B'
ATTACK
FACE
WALL
F15
DIM 'B'
DIM 'B'
CLEARANCE HOLES
TO SUIT BOLT SIZE
THROUGH RHS
50
40
10
THK
DIMS IN RHS
SECTION 'A-A'
28
167
50
50
END POST - BOLTED OPTION
50
167x 6 THK LOOSE PLATE
B
A
14 Ø HOLES
FOR F12 FIXINGS
CLEARANCE HOLE TO SUIT
BOLT SIZE THROUGH RHS
DIM 'B'
DIM 'E' (LENGTH OF 167x6 THICK PLATE - FULL HEIGHT IF NO CEILING REQUIRED)
DIM 'B'
SECTION 'B-B'
M8 BOLT
(MIN)
DIM 'B'
DIM 'B'
13 Ø HOLES
N/S FACE
26 Ø HOLES
OPP FACE
DIMS IN PLT
100x100
x6 RHS
DIM 'B'
DIM 'B'
50 50
HOLES FOR M8
(MIN) BOLTS
DRILLED AND
TAPPED THIS
FACE
40
DIMS IN RHS
DIM 'B'
DIM 'B'
17 Ø
HOLES IN
PLATE FOR
F12
FIXINGS
DIM 'B'
DIM 'B'
DIM 'C' (LENGTH OF 100x100x6 RHS - FULL HEIGHT IF NO CEILING REQUIRED)
50 50
B
10
THK
DIM 'A' (LENGTH OF 234x6 THICK PLATE)
167
50
LOOSE PLATE
28
LOOSE
PLATE
PLAN VIEW
F12
Securiclad
DIM 'G'
DIM 'F'
ATTACK
FACE
234x6 THK PLATE
WELDED TO RHS
36
50
DIM 'D'
50
28
28
36
6
28
100 (100)
48
234
6
THK
DIM 'B'
DIM 'B'
6 Ø HOLES
FOR F16 FIXINGS
28
117
234
DIM 'B'
DIM 'B'
234x 6 THK LOOSE PLATE
DIM 'B'
DIM 'B'
75
40
10
THK
DIMS IN RHS
SECTION 'A-A'
100x234x10 THK
BASE PLATE
28
50
50
DIMS IN PLT
INLINE POST - TAMPER OPTION
26
6
50
CLEARANCE HOLE
TO SUIT BOLT SIZE
THROUGH RHS
6 Ø HOLES
FOR F16 FIXINGS
B
A
26
CUSTOMER DIMS
DIM A
DIM B
DIM C
DIM D
DIM E
DIM F
DIM G
SECTION 'B-B'
F16
F16
13 Ø HOLES
N/S FACE
26 Ø HOLES
OPP FACE
DIM 'B'
DIM 'B'
HOLES FOR M8
(MIN) BOLTS
DRILLED AND
TAPPED THIS
FACE
DIM 'B'
DIM 'B'
50 50
DIM 'E' (LENGTH OF 234x6 THICK PLATE - FULL HEIGHT IF NO CEILING REQUIRED)
6 Ø HOLES
IN PLATE
40
DIMS IN RHS
DIM 'B'
DIM 'B'
DIM 'B'
50 50
DIM 'B'
DIM 'C' (LENGTH OF 100x100x6 RHS - FULL HEIGHT IF NO CEILING REQUIRED)
DIM 'B'
100x100
x6 RHS
B
10
THK
DIM 'A' (LENGTH OF 234x6 THICK PLATE)
DRILL &
TAP HOLE
FOR M8
(MINIMUM)
BOLT
6 Ø HOLES
IN PLATE
4 No. 14 Ø HOLES
FOR F15 FIXINGS
26
48
26
DIM 'B'
DIM 'B'
6
DIM 'B'
DIM 'B'
DIM 'B'
26
28
6 Ø HOLES
FOR F16 FIXINGS
100
234
6 PLT
26
234
A
234x6 THK PLATE
CLEARANCE HOLES
TO SUIT BOLT SIZE
THROUGH RHS
117
LOOSE PLATE
ATTACK
FACE
M8 BOLT
(MIN)
PLAN VIEW
F16
LOOSE
PLATE
F16
Securiclad
234
6 PLT
DIM 'G'
DIM 'F'
ATTACK
FACE
234x6 THK PLATE
WELDED TO RHS
36
50
DIM 'D'
50
14 Ø HOLES
FOR F12 FIXINGS
36
28
48
26
26
DIM 'B'
100 (100)
DIM 'B'
DIM 'B'
6
DIM 'B'
DIM 'B'
48
28
26
28
26
6
28
234
6
THK
DIM 'B'
DIM 'B'
14 Ø HOLES
FOR F12 FIXINGS
28
117
234
234x 6 THK LOOSE PLATE
ATTACK
FACE
DIM 'B'
DIM 'B'
DIM 'B'
CLEARANCE HOLES
TO SUIT BOLT SIZE
THROUGH RHS
50
50
40
10
THK
DIMS IN RHS
SECTION 'A-A'
100x234x10 THK
BASE PLATE
28
DIM 'B'
DIM 'E' (LENGTH OF 234x6 THICK PLATE - FULL HEIGHT IF NO CEILING REQUIRED)
DIM 'B'
DIM 'B'
DIM 'B'
50
INLINE POST - BOLTED OPTION
26
6
50
CLEARANCE HOLE
TO SUIT BOLT SIZE
THROUGH RHS
14 Ø HOLES
FOR F12 FIXINGS
B
A
26
CUSTOMER DIMS
DIM A
DIM B
DIM C
DIM D
DIM E
DIM F
DIM G
SECTION 'B-B'
F12
13 Ø HOLES
N/S FACE
26 Ø HOLES
OPP FACE
DIMS IN PLT
DIM 'B'
DIM 'B'
DIM 'B'
HOLES FOR M8
(MIN) BOLTS
DRILLED AND
TAPPED THIS
FACE
40
DIMS IN RHS
50 50
DIM 'B'
50 50
17 Ø HOLES
IN PLATE
FOR F12
FIXINGS
DIM 'B'
DIM 'C' (LENGTH OF 100x100x6 RHS - FULL HEIGHT IF NO CEILING REQUIRED)
DIM 'B'
100x100
x6 RHS
B
10
THK
DIM 'A' (LENGTH OF 234x6 THICK PLATE)
DRILL &
TAP HOLE
FOR M8
(MINIMUM)
BOLT
17 Ø HOLES
IN PLATE
FOR F12
FIXINGS
4 No. 14 Ø HOLES
FOR F15 FIXINGS
100
234
A
234x6 THK PLATE
117
LOOSE PLATE
M8 BOLT
(MIN)
PLAN VIEW
LOOSE
PLATE
F12
Securiclad
14 Ø HOLES
FOR F12 FIXINGS
167
100 (100) 6
6
ATTACK
FACE
DIM 'F'
28
100x100x6 RHS
'TOP'
CUSTOMER DIMS
DIM A
DIM B
DIM C
DIM D
DIM E
DIM F
DIM G
DIM H
DIM J
DIM K
DIM L
17 Ø HOLES
FOR F12 FIXINGS
6
167
100 (100)
28
DIM 'L'
17 Ø HOLES
FOR F12 FIXINGS
DIM 'J'
DIM 'J'
DIM 'B'
28
DIM 'B'
167
DIM 'G'
DIM 'D'
DIM 'H'
'TOP'
167x167x6 THK
EXTERNAL WELDED
ANGLE
60x60x3 THK
INTERNAL LOOSE
167x167x10 THK
ANGLE
BASE PLATE
SECTION 'A-A'
DIM 'B'
17 Ø HOLES
FOR F12
FIXINGS
37
106
56
61
130
37
167
4 No. 14 Ø HOLES
FOR F15 FIXINGS
DIM 'B'
'B'
61
30
56
106
BASE PLATE DETAIL
(SCALE 1:5)
F12
DIM 'L'
60x60x3 THK
LOOSE ANGLE
F12
(SCALE 1:5)
25
PLAN VIEW
CORNER POST - BOLTED OPTION
LOOSE ANGLE
14 Ø HOLES
FOR F12
FIXINGS
SECTION 'B-B'
35
85
75
'A'
DIM 'L'
ATTACK
FACE
60
DIM 'B'
DIM 'B'
DIM 'B'
60
DIM 'B'
'A'
130
30
DIM 'B'
DIM 'E' (LENGTH OF 60x60x3 THICK ANGLE)
'B'
DIM 'B'
17 Ø HOLES
FOR F12
FIXINGS
DIM 'C' (LENGTH OF 100x100x6 RHS)
DIM 'B'
DIM 'B'
DIM 'B'
DIM 'B'
DIM 'A' (LENGTH OF 167x167x6 THICK ANGLE)
100x100x6
RHS
167
167x167x10 THK
BASE PLATE
167x167x6 THK
WELDED ANGLE
10
THK
BASE
DIM 'K' (O/ALL LENGTH)
(SCALE 1:5)
Securiclad
6 Ø HOLES
FOR F16 FIXINGS
167
DIM 'F'
ATTACK
FACE
6
28
CUSTOMER DIMS
DIM A
DIM B
DIM C
DIM D
DIM E
DIM F
DIM G
DIM H
DIM J
DIM K
DIM L
DIM 'G'
6 Ø HOLES
FOR F16 FIXINGS
6
28
6 Ø HOLES
FOR F16 FIXINGS
28
DIM 'J'
DIM 'B'
28
167
100 (100)
DIM 'B'
167
100x100x6 RHS
'TOP'
DIM 'D'
DIM 'H'
'TOP'
DIM 'J'
100 (100) 6
167x167x6 THK
EXTERNAL WELDED
ANGLE
60x60x3 THK
INTERNAL LOOSE
167x167x10 THK
ANGLE
BASE PLATE
SECTION 'A-A'
DIM 'B'
106
56
61
130
61
30
56
106
BASE PLATE DETAIL
(SCALE 1:5)
F16
F16
F16
110
(SCALE 1:5)
25
60
75
LOOSE ANGLE
6 Ø HOLES
FOR F16
FIXINGS
SECTION 'B-B'
PLAN VIEW
CORNER POST - TAMPER OPTION
60x60x3 THK
LOOSE ANGLE
DIM 'L'
'A'
DIM 'L'
ATTACK
FACE
60
DIM 'B'
DIM 'B'
DIM 'B'
60
DIM 'B'
'A'
37
37
167
4 No. 14 Ø HOLES
FOR F15 FIXINGS
DIM 'B'
'B'
6 Ø HOLES
FOR F16
FIXINGS
6 Ø HOLES
FOR F16
FIXINGS
130
30
DIM 'B'
'B'
DIM 'B'
DIM 'E' (LENGTH OF 60x60x3 THICK ANGLE)
DIM 'C' (LENGTH OF 100x100x6 RHS)
DIM 'B'
DIM 'B'
DIM 'B'
DIM 'B'
DIM 'A' (LENGTH OF 167x167x6 THICK ANGLE)
100x100x6
RHS
167
167x167x10 THK
BASE PLATE
167x167x6 THK
WELDED ANGLE
10
THK
BASE
DIM 'K' (O/ALL LENGTH)
(SCALE 1:5)
Securiclad
SECTION
9
‘SECURICLAD SE’
SMALL ENCLOSURE
100
10mm THICK PLATE
WELDED INTERNALLY.
FULL LENGTH OF POST
STANDARD
CORNER POST.
SEE DRG. SEC/DET/40000 (TAMPER)
SEE DRG. SEC/DET/40100 (BOLTED)
DOOR LINTEL
3
ASCOT DOOR
130
50
200
DOOR POST WITH
ADDITIONAL STEEL
WELDED INTERNALLY
'B'
DOOR HEADER
(PANEL 250mm MIN)
130x100x3 THK L
DOOR FIXED WITH
M10 FIXINGS
A11 - 180x180x2 THICK ANGLES.
3 FIXINGS (MIN)
SEE DRG. SEC/DET/40400
130
CEILING PANEL
900-1190 WIDTH
100
100x174x10
THK BASE PLT
6 THK
136
200x136x6 THK L
SECTION 'A-A'
DOOR LINTEL
130x100 BOX
'B'
'C'
130
SR2/SR3/SR4 PANELS.
ATTACK FACE.
900-1190 WIDE
DOOR LOCKING
MECHANISM. SEE
DRAWING
SEC/SAP/31600/REVA
L/H DOOR POST
'A'
DOOR LINTEL WELDED IN PLACE
'C'
R/H DOOR POST
SECTION 'B-B'
'A'
130
DOOR LINTEL
130x100 BOX
C10 CHANNEL FLOOR TRACK.
SEE DRG. SEC/DET/40800
DOOR POST WITH
ADDITIONAL STEEL
WELDED INTERNALLY
SMALL ENCLOSURE WITH
DOOR HEADER
ASCOT DOOR
A364S - LPS1175
SECURITY DOOR
NOTE: THIS DOOR TO BE USED ON ALL
SR2, SR3 & SR4 ENCLOSURES
NOTE:
MINIMUM OVERALL HEIGHT OF
ENCLOSURE IS 2500mm
MAXIMUM OVERALL HEIGHT IS 3000mm
50
10mm THICK PLATE
WELDED INTERNALLY.
FULL LENGTH OF POST
SECTION 'C-C'
Securiclad
100
10mm THICK PLATE
WELDED INTERNALLY.
FULL LENGTH OF POST
STANDARD
CORNER POST.
SEE DRG. SEC/DET/40000 (TAMPER)
SEE DRG. SEC/DET/40100 (BOLTED)
130x100 BOX x 6 THICK
DOOR LINTEL
'B'
136
3
200x136x6 THK L
SECTION 'A-A'
DOOR LINTEL
130x100 BOX
SR2/SR3/SR4 PANELS.
ATTACK FACE.
900-1190 WIDE
'C'
130
DOOR LOCKING
MECHANISM. SEE
DRAWING
SEC/SAP/31600/REVA
ASCOT DOOR
130
50
200
DOOR POST WITH
ADDITIONAL STEEL
WELDED INTERNALLY
'B'
130x100x3 THK L
DOOR FIXED WITH
M10 FIXINGS
A11 - 180x180x2 THICK ANGLES.
3 FIXINGS (MIN)
SEE DRG. SEC/DET/40400
130
CEILING PANEL
900-1190 WIDTH
100
100x174x10
THK BASE PLT
6 THK
'A'
L/H DOOR POST
DOOR LINTEL WELDED IN PLACE
'C'
R/H DOOR POST
SECTION 'B-B'
'A'
C10 CHANNEL FLOOR TRACK.
SEE DRG. SEC/DET/40800
130
DOOR LINTEL
130x100 BOX
50
DOOR POST WITH
ADDITIONAL STEEL
WELDED INTERNALLY
SMALL ENCLOSURE WITH
DOOR HEADER
10mm THICK PLATE
WELDED INTERNALLY.
FULL LENGTH OF POST
ASCOT DOOR
A364S - LPS1175
SECURITY DOOR
NOTE: THIS DOOR TO BE USED ON ALL
SR2, SR3 & SR4 ENCLOSURES
NOTE:
MINIMUM OVERALL HEIGHT OF
ENCLOSURE IS 2200mm
MAXIMUM OVERALL HEIGHT IS 2500mm
SECTION 'C-C'
Securiclad
ASCOT DOORS MANUFACTURE A SINGLE LEAF DOOR WHICH IS
APPROVED FOR USE WITHIN THE SECURICLAD PANEL SYSTEM AND
UNDER THE LCPB SCOPE & ACHIEVES AN SR4 RATING.
IT HAS A MODIFIED LOCK KEEP DESIGNED TO INCREASE THE
RESISTANCE TO ATTACK WITH THE ADDITION OF A 20mm THICK BLOCK
OF STAINLESS STEEL WELDED TO THE REAR OF THE LOCK KEEP.
Securiclad
HOLES FOR M10 BOLTS
<*> = DIMS TO SUIT DOOR
FRAME
22
DIM 'E'
130
<*>
50
6 Ø FOR
F16 FIXINGS
100 (100)
50
100
DIM 'C'
130
B
100
4
<*>
10mm THICK PLATE
WELDED INTERNALLY.
FULL LENGTH OF LINTEL
DIM 'F'
CUSTOMER DIMS
DIM A
DIM B
DIM C
DIM D
DIM E
DIM F
HOLES FOR M10 BOLTS.
SPACINGS TO SUIT
DOOR FRAME
DOOR LINTEL
<*>
SECTION 'B-B'
(SCALE 1:5)
200
200x136x6 THICK L
6
136
100
DIM 'C'
<*>
10mm THICK PLATE
WELDED INTERNALLY.
FULL LENGTH OF POST
<*>
DIM 'B' (LENGTH OF 130x100x3 THICK L)
(SCALE 1:5)
130x100x3 THICK L
130
SECTION 'A-A'
DIM 'C'
<*>
(SCALE 1:5)
174
100x174x 10 THICK
PLATE
A
152
22
2 No. 14 Ø HOLES
FOR F15 FIXINGS
DIM 'D'
28
44
100
<*>
28
A
10 THK
DIM 'A' (LENGTH OF 200x136x6 THICK L)
<*>
B
LEFT FRONT POST - AS DRAWN
RIGHT FRONT POST - OPP HAND
(SCALE 1:10)
BASE PLATE DETAIL
(SCALE 1:5)
Securiclad
SECTION
10
FLASHINGS &
FIXINGS
P2 DECORATIVE FLASHING
(0.5mm THICK STEEL)
P1 DECORATIVE FLASHING
(0.5mm THICK STEEL)
P5 DECORATIVE FLASHING
(0.5mm THICK STEEL)
Securiclad
P3 DECORATIVE FLASHING
(0.5mm THICK STEEL)
P4 DECORATIVE FLASHING
(0.5mm THICK STEEL)
190
P1 DECORATIVE FLASHING
(0.5mm THICK STEEL)
13
25
190
Securiclad
13
25
P2 DECORATIVE FLASHING
(0.5mm THICK STEEL)
Securiclad
P3 DECORATIVE FLASHING
(0.5mm THICK STEEL)
11
55
55
Securiclad
75
11
75
P4 DECORATIVE FLASHING
(0.5mm THICK STEEL)
Securiclad
11
25
40
180
P5 DECORATIVE FLASHING
(0.5mm THICK STEEL)
Securiclad
15
F11
5.5mm Ø x 32mm
TAMPER DRIVE SELF
DRILL SCREWS
F13
F14
F16
F17
F18
F12
F15
5.5mm Ø x 38mm
TAMPER DRIVE SELF
DRILL SCREWS
5.5mm Ø x 61mm
TAMPER DRIVE SELF
DRILL SCREWS
ARGUS SLEEVE ANCHOR
12mm Ø x 60mm LONG
5.5mm Ø x 92mm
TAMPER DRIVE SELF
DRILL SCREWS
M12 ZINC PLATED
DOME HEAD BOLT
AND TAMPER NUT
5.5mm Ø x 135mm
TAMPER DRIVE SELF
DRILL SCREWS
5.5mm Ø x 163mm
TAMPER DRIVE SELF
DRILL SCREWS
Securiclad
SECTION 11
LOUVERS
SECURICLAD PANELS
THERE ARE A NUMBER OF HIGH PERFORMANCE
SECURITY VENTILATION LOUVRES APPROVED
FOR USE WITHIN THE SECURICLAD PANEL
SYSTEM AND UNDER THE LCPB SCOPE. THE
LOUVRES ARE MANUFACTURED BY BY
SURELOCK McGILL AND THEIR TECHNICAL
INFORMATION ARE AS FOLLOWS:
LOUVRE
CK
TA
AT
CE
FA
SECURITY RATING
MAX-AIR-XA1
SR1
MAX-AIR-XA2
SR2
MAX-AIR-XA3
SR3
MAX-AIR-XA4
SR4
SURELOCK McGILL HIGH
PERFORMANCE SECURITY
VENTILATION LOUVRES
Securiclad
NOTE:POSITION OF LOUVRE MUST BE A MINIMUM OF 100mm FROM ANY EDGE OF
WALLING SYSTEM & A MINIMUM OF 100mm BETWEEN ONE OR MORE LOUVRES.