INSTALLATION
INSTRUCTIONS
Accessory
Application
Publication No.
FABRIC REAR PANEL (5P)
P/N0SR95-HL4-211B
SXS1000M5P/M5D
MII 15262
Issue Date
October 2015
Honda Dealer: Please give a copy of these instructions to your customer.
PARTS LIST
(1)
(2)
(5)
STRAP
WITH HOOK
(3)
(4)
LOWER
BUCKLE AND
STRAP
(Exterior View)
UPPER
HOOK AND LOOP
FASTENER
UPPER
BUCKLE
HOOK AND LOOP
FASTENER
(Interior View)
LOWER
ELASTIC CORD
No.
(1)
Description
Stay-put knob
Qty
2
(2)
Short rivet (D-ring strap)
2
(3)
Long rivet (stay put knob)
2
(4)
Webbing/D-ring straps
2
(5)
Fabric rear panel
1
(6)
Installation Instruction URL (not shown)
1
© 2015 American Honda Motor Co., Inc - All Rights Reserved.
0SR95-HL4-211B
1 of 8
2.
TOOLS AND SUPPLIES REQUIRED
Safety goggles
Power drill
Drill bit (4.5 mm)
Rivet installation tool
Awl
USE AND CARE INFORMATION
• Completely read and understand the instructions
before installing this accessory.
• Do not tow the vehicle on an open trailer with
this accessory installed, as the accessory is not
designed for use at highway speeds.
• To clean, sponge with mild soap and cold water,
rinse with a hose and allow it to drip-dry.
• Do not machine wash or dry.
• Use mild detergent to remove stubborn stains.
• The rear window can be rolled up and stowed using
the webbing straps and snaps.
• When not in use, the window roll up webbing straps
can be fastened to themselves using the snaps.
Install the D-ring straps to the bed side covers:
If installing on an SXS1000M5P:
Cut out the “Side Templates” from page 6.
Tape the template to the bed side cover as shown.
Make a mark on the bed side panel by pushing an
awl through the template drill mark. Remove the
template.
Drill a 4.5 mm hole in the marked location.
Install the D-ring strap into the drilled hole using a
short rivet.
Repeat for the opposite side.
<SXS1000M5P>
SIDE TEMPLATE
TOP up fo
or
ide
This s Side
Left
D-RING
STRAP
INSTALLATION
1.
Install the stay-put knobs to the tail gate.
Cut out the “Stay-put Template” from page 8.
Tape the template to the tailgate as shown. Make a
mark on the tailgate by pushing an awl through the
template drill mark. Remove the template.
Drill a 4.5 mm hole in the marked location.
Install the stay-put knob into the drilled hole using
the long rivet.
Repeat for the opposite side.
SHORT
RIVET
If installing on a SXS1000M5D:
Remove the upper rear bolt from the bed side color
panel.
Reinstall the bolt through the D-ring strap as shown.
Repeat for the opposite side.
<SXS1000M5D>
STAY-PUT TEMPLATE
LONG RIVET
STA
TEM Y-PUT
PLA
TE
LEF
T
STAY-PUT KNOB
BOLT
D-RING
STRAP
2 of 8
0SR95-HL4-211B
© 2015 American Honda Motor Co., Inc - All Rights Reserved.
3.
Wrap the two long hook-and-loop fasteners around
the upper horizontal frame tube.
5.
HOOK-AND-LOOP FASTENER
Attach the hook at the upper corner of the rear panel
to the bracket at the upper rear corner of the cab
frame as shown.
• Do not tighten at this time.
Repeat for the opposite side.
REAR PANEL
HORIZONTAL
FRAME TUBE
CAB FRAME
UPPER CORNER
4.
J-HOOK
Remove the lower rear strap from the buckle at the
lower outside corner of the rear panel.
Wrap the strap around the lower frame tube, through
the loop at the end of the strap, and thread it back
through the buckle.
• Do not pull it tight at this time.
Repeat for the other side.
LOOOP AT END
OF STRAP
BUCKLE
LOWER
STRAP
6.
LOWER
FRAME TUBE
Fasten the rear hook-and-loop fastener at the side
of the rear panel around the net attachment bracket
and then back to the hook fastener on the rear panel.
Repeat for the other side.
LOOP FASTENER
HOOK
FASTENER
NET
ATTACHMENT
BRACKET
LOOP FASTENER
HOOK FASTENER
© 2015 American Honda Motor Co., Inc - All Rights Reserved.
0SR95-HL4-211B
3 of 8
7.
Attach the elastic pulls to the stay-put knobs installed
in Step 1.
ELASTIC PULL
STAY-PUT KNOB
8.
Tighten all the straps and buckles to fully tighten the
fabric rear panel and remove any wrinkles.
Adjust the side straps and hook and loop fasteners
as needed.
Secure the lower rear hook and loop straps to the
D-ring straps installed in Step 2.
LOWER REAR
HOOK AND LOOP
STRAP
D-RING STRAP
LOWER REAR
BUCKLE
LOWER REAR STRAP
4 of 8
0SR95-HL4-211B
© 2015 American Honda Motor Co., Inc - All Rights Reserved.
THIS PAGE LEFT BLANK
INTENTIONALLY
© 2015 American Honda Motor Co., Inc - All Rights Reserved.
0SR95-HL4-211B
5 of 8
<TEMPLATE>
SIDE TEMPLATES
TOP
This side up for Left side
TOP
This side up for Right side
10
30
SCALE
20
40
NOTICE
50mm
10
6 of 8
If you print this template from
your local computer, make sure
the printer settngs do not “scale”
or “shrink” the page.
SCALE
20
30
40
50mm
0SR95-HL4-211B
© 2015 American Honda Motor Co., Inc - All Rights Reserved.
THIS PAGE LEFT BLANK
INTENTIONALLY
© 2015 American Honda Motor Co., Inc - All Rights Reserved.
0SR95-HL4-211B
7 of 8
<TEMPLATE>
STAY-PUT
TEMPLATE
STAY-PUT
TEMPLATE
RIGHT
LEFT
10
30
SCALE
20
40
NOTICE
50mm
10
8 of 8
If you print this template from
your local computer, make sure
the printer settngs do not “scale”
or “shrink” the page.
SCALE
20
30
40
50mm
0SR95-HL4-211B
© 2015 American Honda Motor Co., Inc - All Rights Reserved.