Digital Application Sheet
VEHICLE MANUFACTURER
MITSUBISHI
MODEL
Shogun / Pajero / Montero
YEAR OF MANUFACTURE
2007 on
ENGINE TYPE
3.2 DI-DC
TRANSMISSION
5 Speed Manual
VOLTAGE
12v
STONERIDGE DIGITAL KIT FOR THIS VEHICLE: 7800-078
PARTS LIST
QUANTITY
SE5000 TACHOGRAPH
1
ADAPTOR KIT
1
SENDER
1
RIGHT ANGLE SENDER CABLE
1
SHROUD SEALING KIT
1
DRIVER QUICKGUIDE
1
INSTALLATION KIT
1
MINITIMER D CONNECTOR (BROWN)
1
STONERIDGE PART NO.
6800333
APPLICATION SHEET
A KRM series SE5000 programmed using the SE5000 Configuration System
can
also be used in thisPART
vehicle.
VEHICLE
MANUFACTURERS
NO.
ADDITIONAL VEHICLE MANUFACTURERS PARTS REQUIRED
The cover on the end of the prop shaft should be unbolted to allow access to the speed
sensor before the installation is carried out.
FITTING INFORMATION
KITAS 2 SENDER
STONERIDGE ADAPTOR
Workshop Technical Support
Sales Office
Tel +44 (0)1382 866 400 (choose opt.2. opt.1 )
Tel +44 (0)1382 866 400 (choose opt.1)
Fax +44(0) 1382 866 401
Fax +44(0) 1382 866 401
Email [email protected]
Email [email protected]
COMPLETE UNIT
Whilst we have endeavoured to ensure the accuracy of the information supplied, Stoneridge Electronics cannot be held responsible for any errors or omissions. It is the installer's responsibility to ensure
compliance with specific vehicle manufacturers repair procedures, especially with regard to the procedure for disconnection/reconnection of the battery. Failure to comply with the vehicle manufacturers
instructions may result in personal injury and/or component damage/data loss.
SE5000 Programming Sheet
PROGRAMMING PARAMETERS FOR FITTING THIS VEHICLE WITH AN SE5000 KRM SERIES TACHOGRAPH.
Note. Read the parameters of the tachograph to be replaced, and note all connections to the tachograph,
paying particular attention to Vpulse, dual axle configuration, D8 serial data, Revs input etc.
The below vehicle settings are the default vehicle settings which should be applied. However, individual
vehicle specifications may vary.
Default setting for D6 outputs that can be switched between ISO & Open collector (o/c) is ISO.
The vehicle must be calibrated in an approved manner after fitting.
The road speed limiter must be calibrated after a replacement tachograph is fitted.
The illumination of the KRM series tachograph can be changed between White & Green, please select the
colour best suited to the vehicle illumination.
If you are in doubt regarding the replacement of any tachograph with a KRM series product please call:Workshop Support on 0870 887 9200 option2, option1. or email [email protected]
TACHOGRAPH
CANBUS CAN
5002KRM
N/A
CAN
TERMINATION
ILLUMINATION
N/A
A2
N/A
C3
READ ALL DATA LOG
PARAMETER
VALUE / SETTING
PARAMETER
90km/H
D6
O/C
VALUE / SETTING
Def. KEY ON/OFF
RPM FACTOR
D4 PIN FUNCTION
D5 PIN FUNCTION
D6 PIN FUNCTION
D7 PIN FUNCTION
SERIAL DATA OUT (D8)
C1 PIN FUNCTION
FILTER PIN B3
CAN TRIP RESET
CAN WAKE UP
RD CAN CONFIG
W-FACTOR
K-FACTOR
L-FACTOR
TYRE SIZE
VIN
VRN
VEH. REG. NATION
PREF. LANGUAGE
CURRENT TIME
CURRENT DATE
TIME OFFSET
NEXT CALIB.DATE
INSTALL DATE
ACTIVATION TIME
SERVICE DELAY
ODOMETER
O/P SHAFT FACTOR
SPEEDO OP FACTOR
RESET HEARTBEAT
LOW SPEED LIMIT
REVS INPUT SPEED LIMITER
SETTING
ADD. EVENT REC.
READ ONLY. –DATE FORMAT / UNACTIVATED
BACKLIGHT SELECT
ILLUMINATION LEVEL
ILLUMINATION OFF
ENG. SPEED REC.
VRESD
VEH. SPEED REC.
VRVSD
PRE-OVERSPEED
PRE-NEXT CALIBRATION
WARRANTY TIME
LOW POWER BAND
ECONOMY POWER BAND
POOR ECONOMY
Workshop Technical Support
Sales Office
Tel +44 (0)1382 866 400 (choose opt.2. opt.1 )
Tel +44 (0)1382 866 400 (choose opt.1)
Fax +44(0) 1382 866 401
Fax +44(0) 1382 866 401
Email [email protected]
Email [email protected]
Whilst we have endeavoured to ensure the accuracy of the information supplied, Stoneridge Electronics cannot be held responsible for any errors or omissions. It is the installer's responsibility to ensure
compliance with specific vehicle manufacturers repair procedures, especially with regard to the procedure for disconnection/reconnection of the battery. Failure to comply with the vehicle manufacturers
instructions may result in personal injury and/or component damage/data loss.
Digital Application Sheet
1. Locate the original Speed Sensor.
2. Disconnect the cable by removing the locking pin which can be unclipped and slide out
then cable tie the connector out of the way.
3. Remove the original speed sensor by unscrewing the 6mm bolt.
4. Locate the Stoneridge Adaptor in the kit
provided.
5. Apply gasket seal to the adaptor as
shown .
6. Install Stoneridge Adaptor ensuring
security screw provided is fitted securely.
Workshop Technical Support
Sales Office
Tel +44 (0)871 700 7070 (choose opt.2. opt.1 )
Tel +44 (0)871 700 7070 (choose opt.1)
Fax +44(0) 870 704 0002
Fax +44(0) 870 704 0002
Email [email protected]
Email [email protected]
Whilst we have endeavoured to ensure the accuracy of the information supplied, Stoneridge Electronics cannot be held responsible for any errors or omissions. It is the installer's responsibility to ensure
compliance with specific vehicle manufacturers repair procedures, especially with regard to the procedure for disconnection/reconnection of the battery. Failure to comply with the vehicle manufacturers
instructions may result in personal injury and/or component damage/data loss.
Digital Application Sheet
8. Run the sender cable along the gearbox and
7. Screw Kitas 2 sender onto the Stoneridge
behind the heat shield following the other
Adaptor and seal the sender to the gearbox
cables ensuring it is cable tied regularly.
using the security wire and security screw.
9. Feed the sender cable through the right
angle cable grommet on the passengers
side in the engine bay.
10. Remove original facia around the Money /
Card holder tray by popping of the clips.
11. Remove the 2 screws behind the facia securing the original Money / Card holder
tray.
12. Replace the original facia by pushing back
in the original clips.
Workshop Technical Support
Sales Office
Tel +44 (0)871 700 7070 (choose opt.2. opt.1 )
Tel +44 (0)871 700 7070 (choose opt.1)
Fax +44(0) 870 704 0002
Fax +44(0) 870 704 0002
Email [email protected]
Email [email protected]
Whilst we have endeavoured to ensure the accuracy of the information supplied, Stoneridge Electronics cannot be held responsible for any errors or omissions. It is the installer's responsibility to ensure
compliance with specific vehicle manufacturers repair procedures, especially with regard to the procedure for disconnection/reconnection of the battery. Failure to comply with the vehicle manufacturers
instructions may result in personal injury and/or component damage/data loss.
Digital Application Sheet
13. Locate the fuse box to the bottom right
hand side of the steering wheel.
14. Remove the facia around the fuse box by
popping out the securing clips.
15. Use the following wires to power the tachograph:Red wire marked 1 goes to connector A1
of tachograph through a 1 amp fuse,
marked 5.
Alternatively - The feed for the ignition and
power can be taken from the radio, with
the feed for the illumination and ground
taken from the cigarette lighter. Ensure a
suitable 1 amp fuse is used.
Green/White wire marked 2 goes to
connector A2 of tachograph.
Red/Yellow wire marked 3 goes to
connector A2 of tachograph.
Black/Red wire marked 4 goes to
connector A5 & A6 of tachograph.
Workshop Technical Support
Sales Office
Tel +44 (0)871 700 7070 (choose opt.2. opt.1 )
Tel +44 (0)871 700 7070 (choose opt.1)
Fax +44(0) 870 704 0002
Fax +44(0) 870 704 0002
Email [email protected]
Email [email protected]
Whilst we have endeavoured to ensure the accuracy of the information supplied, Stoneridge Electronics cannot be held responsible for any errors or omissions. It is the installer's responsibility to ensure
compliance with specific vehicle manufacturers repair procedures, especially with regard to the procedure for disconnection/reconnection of the battery. Failure to comply with the vehicle manufacturers
instructions may result in personal injury and/or component damage/data loss.
Digital Application Sheet
16. Connect a wire from pin D6 on the tachograph to the White/Blue wire on the connector behind the cigarette lighter to drive
the speedometer.
17. The tachograph can now be connected
and installed.
18. The tachograph is now ready for calibration.
19. The D6 on the tachograph must be set
to Speedometer using the MKII Programmer and the Speedo output factor
should be set so that the speedometer
matches the tachograph.
Workshop Technical Support
Sales Office
Tel +44 (0)871 700 7070 (choose opt.2. opt.1 )
Tel +44 (0)871 700 7070 (choose opt.1)
Fax +44(0) 870 704 0002
Fax +44(0) 870 704 0002
Email [email protected]
Email [email protected]
Whilst we have endeavoured to ensure the accuracy of the information supplied, Stoneridge Electronics cannot be held responsible for any errors or omissions. It is the installer's responsibility to ensure
compliance with specific vehicle manufacturers repair procedures, especially with regard to the procedure for disconnection/reconnection of the battery. Failure to comply with the vehicle manufacturers
instructions may result in personal injury and/or component damage/data loss.