Stucco Brickmould for a Nail
Fin Window (Three Side)
Installa on Instruc ons
LA7956 ‐ A
Nail Fin Stucco Brickmould InstrucƟons
For Milgard Essence Series® Windows and Doors

Install Window per AAMA 2400‐10 installa on standard.

Read instruc ons from beginning to end before assembling or installing Stucco Brickmould.

Stucco Brickmould is not compa ble with other Milgard Window or Door offerings.

Do not use Stucco Brickmould on other manufacturers’ products.

Window must be properly installed and flashed prior to Stucco Brickmould installa on.

Milgard Nail Fin Stucco Brickmould does not provide structural support or func on as a water barrier.

Use exterior grade high quality sealants. For compa ble TiteBond® Sealant colors refer to page 15.
Required Tools
Screwdriver with #2 Phillips bit
Caulking Gun
LA7956 ‐ A
2
Nail Fin Stucco Brickmould Parts
Stucco Brickmould with Groove Filler
PART
DESCRIPTION
PART NUMBER
Stucco Brickmould with Stucco Key
PART
DESCRIPTION
PART NUMBER
1
STUCCO BRICKMOULD ‐ HEADER
EX7853XX
1
STUCCO BRICKMOULD ‐ HEADER
EX7853XX
2
STUCCO BRICKMOULD ‐ LEG ‐ LEFT
EX7853XX
2
STUCCO BRICKMOULD ‐ LEG ‐ LEFT
EX7853XX
3
STUCCO BRICKMOULD ‐ LEG ‐ RIGHT
EX7853XX
3
STUCCO BRICKMOULD ‐ LEG ‐ RIGHT
EX7853XX
4
GROOVE FILLER
EX7852XX
4
STUCCO KEY
EX7812XX
5
CORNER KEY
IM8029MI
5
CORNER KEY
IM8029MI
6
TRIM CLIP
IM8028MI
6
TRIM CLIP
IM8028MI
7
FOAM PLUG
MI7514
7
FOAM PLUG
MI7514
8
#8‐5/8” FLAT HEAD SS SCREW
FA0442SS
8
#8‐5/8” FLAT HEAD SS SCREW
FA0442SS
9
(WINDOW FRAME)
VARIES
9
(WINDOW FRAME)
VARIES
LA7956 ‐ A
3
Nail Fin Stucco Brickmould Corners
Top Miter
Exterior View
Interior View
Bo om Groove Filler
Exterior View
Interior View
Bo om Stucco Key
Stucco Brickmould with Stucco Key shown
Exterior View
Interior View
Stucco Brickmould shown in yellow
Window Frame shown in blue
LA7956 ‐ A
4
Special InstrucƟons for Shape and Radius Windows

Install Window per AAMA 2400‐10 installa on standard.

Milgard provides Shape and Radius Stucco Brickmould clipped to Window Frame.

Remove trim by gently pulling on any corner.

Skip to Step 6 for Trim Installa on.
LA7956 ‐ A
5
Corner Key Assembly
Skip to Step 11 if installing Factory Assembled Stucco Brickmould
1
Determine Header, Sill, and Leg Trim Pieces.
Insert Corner Keys into Stucco
Brickmould miter ends.
2
Start #8 x 5/8” Flat Head Screw into one hole. Tighten screw halfway.
Repeat for all Corner Keys.
LA7956 ‐ A
6
Install Screws
3
Locate all Screw Holes. With screw halfway Ɵghtened, rotate screw head unƟl second Corner
Key Screw Hole appears.
4
Inject sealant into Corner Keys (half a squeeze per Corner Key).
LA7956 ‐ A
7
Install Screws (ConƟnued)
5
Install #8 x 5/8” Flat Head Screws.
Miter Corners
Start screw into second hole and
ghten un l head is flush with
Stucco Brickmould. Finish
ghtening first Screw.
LA7956 ‐ A
8
Trim Clip AƩachment
6
Install Trim Clips onto Stucco Brickmould.
Space Trim Clip 1.5” away from corner. Tap two
Trim Clips into each corner.
Install Trim Clip 1.5" away from bo om of each
Stucco Brickmould Jamb.
If length of Window Jamb or Header is
47" or longer, tap an addi onal Trim
Clip in middle of side.
If necessary, install addi onal Trim
Clips no more than 4' on center.
LA7956 ‐ A
9
Flashing Flange OpƟon
Warning! Flashing Flange will not hold or secure Window in Rough Opening.
Do not puncture Flashing Flange.
Skip to Step 10 if not installing opƟonal Flashing Flange.
7
Determine which Flashing Flange fits Stucco Brickmould Trim piece.
Length of Flashing Flange is close to the
length of Stucco Brickmould.
8
Press Flashing Flange into Stucco Brickmould Groove.
Do not install Flashing Flange along Sill
or boƩom of Window.
Insert Header Flashing Flange first. Insert Leg Flashing Flange flush with Header Flashing Flange.
LA7956 ‐ A
10
Flashing Flange OpƟon (ConƟnued)
9
Fold Corner Gaskets around corners.
Exterior
Before
A er
Interior
Before
LA7956 ‐ A
A er
11
End Plug InstallaƟon
10
Squeeze foam End Plug into open end of Stucco Brickmould.
Push foam in un l it is flush
with end of Stucco Brickmould.
Repeat for other open end.
LA7956 ‐ A
12
Trim InstallaƟon
11
LA7956 ‐ A
Apply 1/4” diameter 2” long beads of sealant to back of Stucco Brickmould. Space beads
18” apart.
13
Trim InstallaƟon (ConƟnued)
12
Push Stucco Brickmould onto Window Frame.
Place wood block directly on Stucco Brickmould in Trim Clip area. Tap wood block to fully seat
Stucco Brickmould against Window Frame.
LA7956 ‐ A
14
Clean Up

Wipe up any excess sealant.

Clean up scuff marks with soap and water.
TiteBond® WeatherMaster Sealant CompaƟble Colors
Milgard PaleƩe Color
LA7956 ‐ A
Titebond® WeatherMaster™ Color
Reference
Milgard Part Number
Bark
44061
SE7673AR
Black Bean
44031
SE7673BL
Bronze
45841
SE7673ZB
Cinnamon
45521
SE7673CI
Classic Brown
44211
SE7673LW
Espresso
45661
SE7673EX
Evening Sky
45531
SE7673ES
Fern
45651
SE7673FN
Fog
46681
SE7673FO
Frost
44001
SE7673FS
Harmony
44641
SE7673HR
Ivory
45511
SE7673IV
Pea Pod
49211
SE7673PP
Sand
46041
SE7673SD
Tweed
44691
SE7673TE
Twilight
44031
SE7673BL
15
REVISIONS
REV
ECN
A
4019ECNEG
LA7956 ‐ A
DESCRIPTION
RELEASE
DATE
08/17/2015
DRAWN APPD.
NDS
VM
16