Ground engaging tools
in Action
1
Sandvik GET
total bucket concept
Sandvik GET
mechanical lip system
Sandvik’s integrated bucket solutions
Sandvik GET mechanically attached lip shrouds provide
a quick-change innovative wear solution for underground
loaders. Many lip systems require a costly weld build to
the rear of the boss – or even boss replacement – to enable
effective shroud re-tensioning.
However, unlike conventional systems, Sandvik GET’s
adjustable locking system can be re-tensioned easily
and safely to minimise the destructive lip peening often
experienced with loose fitting shrouds. This is achieved
simply by tightening the rear cap screw – making the
placement of the boss much less critical and providing a
quick and cost-effective solution.
Sandvik introduces its total bucket concept for underground
LHDs and loaders.
Our integrated bucket ground engaging tool (GET) solutions
guarantee longer bucket life, reduced wear and lower whole-ofbucket costs.
Sandvik’s “whole-of-bucket” approach to the GET business,
provides bucket wear systems that increase bucket life,
delivering lower overall costs, and reducing costs per tonne of
material in underground mining operations.
In particular the focus has been on developing GET systems
for underground mining operations – where there has been
a lack of R&D investment by existing GET suppliers over a
number of years.
While Sandvik’s GET systems are specifically designed to
meet the challenging requirements of hard rock underground
mining operations, they are also ideally suited to some surface
mining applications.
In addition, Sandvik’s GET systems are suited to a wide
range of OEM buckets and loading products – not just
Sandvik LHDs.
Sandvik’s total bucket concept focuses on four key areas of
bucket GET:
1.Cast corners: By adding structural strength as well as high
wear protection to bucket corners, bucket life is significantly
extended. This area of the bucket is prone to cracking and
high wear exposure, limiting the life of the bucket shell –
Sandvik GET systems provide consistent cost per tonne
savings by extending the operating cycle of the bucket.
2. Mechanical locking system: The hammerless design of
Sandvik’s mechanical locking system allows easy change
outs of individual shrouds. In addition, it enables easy retensioning of the shroud against the lip – eliminating wear
in this area so that the shrouds can be changed out without
having to change the complete lip. This system increases the
life of the base lip – again significantly reducing costs.
3. Heel shrouds: The use of Sandvik heel shrouds minimises
the exposure of the bottom of the bucket shell during the
loading cycle – further prolonging bucket life, and reducing
costs.
4. Protector strips: Sandvik’s mechanically attached protector
strips with superior hardness offer increased protection for
the underside of the bucket, with short change out time and
no welding required – for increased bucket life, reduced
downtime and lower costs.
Main features
• Quicker and easier to change than existing underground
GET systems
• Adjustable locking system reduces costly lip damage and
change out times
• No welding required for change outs
• Low-profile blade provides increased penetration
• High strength, high hardness alloy provides high
resistance to wear.
Spacer
Cap screw
Boss
Locking pin
Shroud
Installation procedure
1. Slide shroud over lip and boss
2.Install locking pin downward into top leg of shroud and
slide it forward
3. Insert spacer down into remaining gap at rear of locking
system
4.Install cap screw through rear of shroud and tighten
5.Insert cap screw plug.
For detailed removal procedures, see pages 6-7.
Sandvik GET 32 mm Series 2 lip shrouds
Applications: Continuous-edge underground loaders
Make
Model
Sandvik
LH205L, LH207L, LH209L, LH306, LH307, LH410
Sandvik EJC
115, 145, 145E, 210, 245, 777
Sandvik Toro
T-6, T-7, 006, 007, 151, 301, 400
Cat Underground
R1300, R1500, R1600
Atlas Copco
ST2.0, ST2.5, ST3.5, ST710, ST1022, ST1030
Sandvik GET 50 mm standard Series 2 lip shrouds
Applications: Larger LHDs in normal mining applications
Make
Model
Sandvik
LH512, LH514, LH517, LH621, LH625E
Sandvik Toro
0100, 0011, 650, 1250, 1400, 2500E, T-8, T-9, T-10, T-11
Cat Underground R1500, R1600, R1700, R2800, R2900, R2920G
Atlas Copco ST88, ST1020, ST1030, ST1520, ST-7.52, ST-8C, ST1800
Sandvik GET 50 mm heavy duty Series 2 lip shrouds
Applications: Larger LHDs in more aggressive mining applications
Make
Model
Sandvik
LH517, LH621,LH625E
Sandvik Toro
0100, 0011, T-10, T-11, 2500E
Cat Underground
R1500, R1600, R1700, R2800, R2900, R2920G
Atlas Copco
ST-8C, ST-1800, ST-1520
For detailed parts numbers, see pages 17–19.
2
3
Sandvik GET 50 mm Series 2 lip assembly details
Sandvik GET Series 2 half corner shrouds
Sandvik GET’s half corner shrouds are a simple solution
when replacing worn corner shrouds on bucket edges.
Replacing worn corner shrouds with standard shrouds
disrupts the continuous cutting edge, which can result in:
• Gouging during roadworks
• Catching the corner shroud
• Higher costs.
In contrast, Sandvik GET half corner shrouds maintain
a continuous cutting edge, improving performance and
reducing costs.
Example of a typical Sandvik GET 50 mm Series 2 lip assembly layout drawing. The Sandvik GET Series 2 mechanical GET system can be made to suit any width lip
in either 32 or 50 mm plate. Layout drawings can be supplied to assist in the fabrication of the lip assembly, ensuring correct alignment to the bucket. Lip assembly
layout drawings also list all required parts. The Sandvik GET 50 mm Series 2 offers two shroud alternatives: standard or heavy duty.
Corner shrouds usually wear out faster
than straight shrouds.
Sandvik GET 50 mm standard Series 2
Item
Sandvik part number
Supplier part number
Description
Qty
A/B*
1
69039955
SBP50-PAS2
Pin assembly
9
A
2
69039951
SBP50X235-CL2
235 mm wide left-hand standard corner shroud
1
A
3
69039952
SBP50X235-CR2
235 mm wide right-hand standard corner shroud
1
A
4
69039950
SBP50X288-T2
288 mm wide standard transition shroud
2
A
5
69039948
SBP50X330-S2
330 mm wide standard straight shroud
2
A
6
69039949
SBP50X420-S2
420 mm wide standard straight shroud
3
A
7
69037874
SPB1X420
Weld-on profile bar 1 420 centre shroud
1
A
8
69039960
SPB50-B2
Weld-on boss
7
B
9
69037854
SCC50X175-LS
Left-hand standard cast corner
1
B
10
69037855
SCC50X175-RS
Right-hand standard cast corner
1
B
Replacing worn corners with
conventional shrouds disrupts the
continuous cutting edge.
Sandvik GET 50 mm heavy duty Series 2
Item
Sandvik part number
Supplier part number
Description
Qty
A/B*
1
69039955
SBP50-PAS2
Pin assembly
9
A
2
69039965
SBP50X235-CLX2
235 mm wide left-hand heavy duty corner shroud
1
A
3
69039966
SBP50X235-CRX2
235 mm wide right-hand heavy duty corner shroud
1
A
4
69039964
SBP50X288-TX2
288 mm wide heavy duty transition shroud
2
A
5
69039962
SBP50X330-SX2
330 mm wide heavy duty straight shroud
2
A
6
69039963
SBP50X420-SX2
420 mm wide heavy duty straight shroud
3
A
7
69037874
SPB1X420
Weld-on profile bar 1 420 centre shroud
1
A
8
69039960
SPB50-B2
Weld-on boss
7
B
9
69037854
SCC50X175-LS
Left-hand standard cast corner
1
B
10
69037855
SCC50X175-RS
Right-hand standard cast corner
1
B
Sandvik half corner
shrouds maintain a
continuous cutting edge.
* A = Consumables B = Initial fitment lip components
4
5
sandvik GET Series 2 lip shrouds removal procedures
1
2
This removal procedure is common for both Sandvik GET 32 mm and 50
mm Series 2 lip shrouds. Shrouds are ready to be changed when the wear
indicators become visible on the base of the shrouds.
3
To begin the removal process wash the shrouds to remove fines that remain
built up around the cap screw and pin assembly.
5
6
Insert pry bar into the cavity under the spacer (shown inset), then pry spacer
up and remove it from the shroud.
Remove the bolt plug from the rear of the cap screw. Then turn the cap screw
counter clockwise and remove the cap screw from the pin assembly.
7
Lever back the pin block until it hits the rear of the cavity.
Item 3
Item 4
When reusing the pin assembly it is recommended to replace the cap screw (Item 2).
Note: The piston and seal can also be replaced if required (Item 1).
Exploded view
The shroud can now be removed from the lip. Following removal, wash down
the lip using a power washer, ensuring the lip profile is clean and ready for
installation of the replacement shroud.
Before performing maintenance work all personnel should ensure they are wearing approved
personal protective equipment. Under NO circumstances should hardened hammers be used on
lip shrouds. If required, a brass-tipped hammer should be used.
Item 2
Sandvik Series 2 pin assembly
Insert a pry bar into the slot between the spacer and the pin block. Then push
the pin block forward to break the seal between them.
8
Using two pry bars lever out the pin block.
9
Item 1
4
Sandvik GET 32 mm Series 2 assembly parts
Sandvik GET 50 mm Series 2 assembly parts
Item
Sandvik part
number
Supplier part
number
Description
Item
Sandvik part
number
Supplier part
number
Description
1
69039976
SBP32-SKS2
Service kit
1
69039956
SBP50-SKS2
Service kit
2
69039977
SBP32-CS2
Cap screw
2
69039957
SBP50-CS2
Cap screw
3
69039978
SBP32-SS2
Spacer
3
69039958
SBP50-SS2
Spacer
4
69039979
SBP32-BP2
Bolt plug (pack of 50)
4
69039959
SBP50-BP2
Bolt plug (pack of 50)
For detailed parts numbers, see pages 17–19.
For more details please contact your local Sandvik office.
6
7
Sandvik GET
protector strip
sandvik GET Protector strip installation and maintenance procedures
Protector strip
Sandvik GET’s newly released protector strip is the
latest development in its on-going R&D program
to provide innovative solutions for abrasive mining
conditions.
This versatile protector strip system is designed
to complement Sandvik GET’s Series 2 mechanically
attached shroud system and its newly released LHD
heel shrouds – providing a total bucket wear
solution. Featuring a patented locking system,
Sandvik GET’s protector strip is a mechanically
attached wear bar designed for use in a wide range
of hard-wearing applications, including:
• Load-haul-dump (LHD) buckets
• Wheel loader buckets
• Excavator/face shovel buckets
• Truck trays
• Chute liners
• Many other applications.
The protector strip provides a simple alternative
to traditional weld-on wear strips, providing the user
with a number of advantages, including:
• No welding required during change outs
• Manufactured using high-tensile alloy steel for
improved wearing properties compared with
traditional QT plate
• Safe and easy to replace and maintain
• Able to be re-tensioned, ensuring the system
remains securely fixed
• Improved productivity through reduced
downtime.
Mounting bracket
Locking pin assembly
Critical fit tapers
Bolt plug
The Sandvik GET protector strip consists of the four components shown
above. It requires two mounting brackets, taper lock assemblies and bolt
plugs for each protector strip.
Before installing or replacing protector strips, ensure the critical fit tapers
on both the mounting brackets and protector strip are free of built-up fines
or particulates.
Assembling the Sandvik GET protector strip system is very straightforward, and is detailed in the following
five simple steps
1
Insert the two threaded pins in the protector strip mounting
brackets.
3
2
Fit the protector strip over the mounting brackets and rotate it
into the critical fit tapers.
4
Sandvik GET protector strip
Applications: Larger underground and surface loaders, including:
Make
Model
Sandvik
LH512, LH514, LH517, LH621, LH625E.
Sandvik Toro
0010, 0011, 650, 1250, 1400, 2500E, T-8, T-9, T-10, T-11
Cat Underground
R1500, R1600, R1700, R2800, R2900, R2920 Extra
Cat surface loaders
966G, 980G, 988G
Atlas Copco
ST-85, ST-8C, ST1020, ST1030, ST1520, ST1800
Tighten to 60 Nm
Insert both wedge pins complete with cap screw assemblies into
the system.
5
For detailed parts numbers, see page 18.
Tighten both taper lock assemblies to 60 Nm (45 lb ft).
Note: It is important that both taper lock assemblies are tightened
simultaneously to ensure even take up.
Before performing maintenance work
all personnel should ensure they are
wearing approved personal protective
equipment. Under NO circumstances
should hardened hammers be used on protector
strips. If required, a brass-tipped hammer should
be used.
Insert rubber bolt plugs to prevent build up of fines in the cap
screw heads.
8
9
Sandvik GET fitting information
and safety procedures on YouTube
You can now access Sandvik GET fitting information and
safety procedures quickly and easily online, through our
videos hosted through the online video service YouTube.
These videos include:
• Sandvik GET protector strip installation procedures
• Sandvik GET corner shroud installation procedures
• Correct installation and maintenance procedures for
Sandvik GET half arrow shrouds, along with wear
indication guidelines
• Sandvik GET shrouds/teeth sectional installation
procedures
To view any of these videos, simply go to the YouTube
website at www.youtube.com and type “Sandvik GET”
into the SEARCH window.
10
Sandvik GET
on-line bucket monitoring system
Sandvik GET’s latest innovative solution to the
challenges in abrasive mining conditions is our
new on-line Sandvik GET Wear Monitoring
System (www.bucketmonitoringsystems.com),
which allows end-users to quickly and easily to
monitor bucket and GET wear.
As a leading provider of bucket wear solutions
for abrasive environments in underground
mining, we believe this monitoring system
revolutionises opportunities for predicing the life
of any bucket and its GET components.
This allows better production planning,
accurate predictions of bucket/GET life, and
more accurate planning of downtime and bucket/
GET changeouts and rebuild – resulting in lower
costs and higher productivity.
Features of this system include:
• Tools to trace and predict the wear rate of a
bucket and its GET
• Scheduling of re-build and GET change outs
• Monitoring the expected life span of each
bucket on site.
• Detailed monitoring of critical areas of the
bucket
The Sandvik GET Wear Monitoring System is
designed to complement Sandvik GET’s bucket
solution.
For more details, please go to
www.bucketmonitoringsystems.com.
Bucket floor graph
Left heel shrouds graph
11
Sandvik GET
surface loader (ROM pad) applications
While originally designed for underground use, Sandvik
GET’s Series 2 lip system is highly suitable for certain surface
applications.
Mine operators have found great success using this system on
wheel loaders working a ROM (run of mine) pad or stockpile
where points or teeth are not required. Such ROM pad loaders
have achieved excellent results and significant cost saving by using
Sandvik GET’s Series 2 continuous edge lip system.
The main benefit of this lip system is its longer wearing
properties and ease of shroud change out.
The adjustable locking system allows the shrouds to be easily
and safely re-tensioned, minimising the destructive lip peening
often experienced with loose fitting shrouds.
This system also incorporates cast corners which add
structural strength as well as higher wear protection to the
bucket corners – extending bucket life significantly.
In ROM pad work, this area of the bucket is typically prone
to cracking and high wear exposure, limiting the life of the
bucket shell.
Sandvik GET’s series 2 system provides consistent cost per
tonne savings by extending the operating cycle of the bucket.
And in highly abrasive applications, Sandvik GET’s
Series 2 system can be coupled with Sandvik GET heel shrouds
and either a weld-on profile bar or our recently developed
mechanically attached Protector Strip
Case study
Caterpillar 972 bucket fitted with Sandvik GET Series 2, heel
shrouds, profile bar and half arrow cheek guards.
Main features of this system include:
• Quicker and easier to change than existing underground
GET systems
• Adjustable locking system reduces costly lip damage and
change out times
• Integral cast corners in high-stress zone
• No welding required for change outs
• Low-profile blade provides increased penetration
• High strength, high hardness alloy provides high resistance
to wear.
• Optional mechanically attached protector strips for increased
wear life.
The end result in this application was lower overall
operating costs, through increased GET and bucket life, reduced
downtime through faster GET change out, and reduced bucket
damage and repair requirements.
Talk to your Sandvik GET representative about the
advantages of using our Sandvik GET Series 2 system on your
ROM pad loaders.
12
Half arrow
Sandvik GET flat corner shroud (surface/ROM PAD applications)
While standard Sandvik GET Series 2 corner shrouds offer
superior wear life through additional wear material, we
also offer a flat corner shroud for improved clean up and
minimal degradation on hard or concrete ROM pads.
This system is ideally suited for ROM pad wheel loaders
including:
• Cat 314G through to 988F
• Komatsu WA150 through to WA700
• Volvo L50F through to L350F
• Hitachi LX110 through to LX450
• Liebherr L510 through to L586.
Standard corner shroud design.
Heel shrouds
Optional “flat” corner shroud.
Sandvik GET flat corner shroud (surface/ROM pad applications) part numbers
Sandvik part number
Supplier part number
Description
69041897
SBP32X210-CRF2
Sandvik GET 32 mm Series 2 R/H Flat Corner Shroud
69041896
69041892
69041893
69041894
Cat 988 bucket fitted with Sandvik GET Series 2.
69041895
SBP32X210-CLF2
SBP50X235-CLF2
SBP50X235-CRF2
SBP50X235-CLFX2
SBP50X235-CRFX2
Sandvik GET 32 mm Series 2 L/H Flat Corner Shroud
Sandvik GET 50 mm Series 2 L/H Flat Corner Shroud
Sandvik GET 50 mm Series 2 R/H Flat Corner Shroud
Sandvik GET 50 mm Series 2 L/H Heavy Duty Flat Corner Shroud
Sandvik GET 50 mm Series 2 R/H Heavy Duty Flat Corner Shroud
Sandvik GET protector strip (surface/ROM PAD applicationS)
Sandvik GET's protector strip (for more details, please
see page 8) is also suitable for ROM pad and surface
applications, on both wheel loaders and excavator/shovels.
Features include:
• Not limited to the primary lip of the bucket, can be
placed on most parts of the underside of the bucket
• Protector strip can be fitted to excavator/shovel buckets
as well as loader buckets
• Layout drawings for correct positioning of protector
strip can be supplied, focusing on critical wear areas.
Liebherr 984 bucket.
Cat 972 bucket fitted with Sandvik GET Series 2, heel shrouds, profile
bar and half arrow cheek guards.
Layout drawing showing full Protector Strip installation on Cat 988 bucket..
Cat bucket fitted with Sandvik GET Series 2 and protector strip.
13
Sandvik GET
Half Arrow weld-on lip system
Half Arrow weld-on lip system installation procedures
Sandvik GET’s Half Arrow weld-on lip system for
continuous edge underground loaders has been specifically
designed to provide maximum penetration while
maximising the amount of available wear material.
With its low profile blade, the Sandvik Half Arrow
system provides excellent penetration, with longer wear life
than a bare lip.
The Sandvik Half Arrow weld-on lip system uses
straight half arrow edges along the length of the lip and in
this configuration is suitable for most digging conditions.
In extreme applications heavy-duty corner edges can
be added.
The Sandvik Half Arrow system provides more available
wear material than other lip systems, minimising the
amount of throwaway material.
This system is ideally suited for continuous edges on all
types of underground loaders.
Recommended welding processes and consumables for Sandvik GET
Traditional “rounding off ” of a standard bucket lip is a major contributor
to lost production tonnes. This type of wear results in reduced
penetration and poor clean up. In addition, as the bucket wears down,
carrying capacity is significantly reduced, while the bucket can suffer
from fatigue as the plate gets thinner.
1. Pre-heat: 150°C (302°F), measured at least 76 mm (3 inches)
either side of the weld joint or the area being gouged.
2.Interpass temperature: 150-250°C (302-482°F),
maintained at least 76 mm (3 inches) either side of the weld
joint or the area being gouged.
3. Post-heat treatment: NOT REQUIRED
Allow the component to cool slowly, but do not quench.
4.Consumables: See table below for requirements and
classifications.
Weld Process
Consumable Classification
Manual Metal Arc
(MMAW)
AS/NZS 1553.1*
AS
AS/NZS (ISO)**
AWS
E4818-5
E 43 16 A U H5
E7018
E4816-4
E 43 16 A U H5
E7016-1
E4818-5
Flux Cored (FCAW)
E 43 16 A U H5
AS 2203.1*
ETP-GMp-504A (ETP-GMp-404P)
ETP-GCp-W503A
ETP-GNn-W503A
Main features
• High penetration edges reduce machine related costs
such as fuel and tyre usage
• High strength, high hardness alloy provides high
resistance to wear
• Efficient design ensures maximum available wear
material and minimum throwaway material.
Gas Metal Arc
(GMAW or MIG)
AS/NZS 4855 / ISO 2560
ETD-GNn-W500A
AS/NZS 2717.1
ES4-GM/C-W503AH
ES6-GM/C-W503AH
AS/NZS ISO 17632
T49 4 T15-1 M A-U H5
T49 2 T1-1 C A-K-U H10
T49 2 T8-1 N A-K-U H15
T 49 Z T7-1 NA H15
N/A
N/A
AWS A5.1
E7018-1
AWS A5.20
E71T-5MJ (E70C-6MH4)
E71T-1
E71T-8
E70T-7
AWS A5.18
ER70S-4
ER70S-6
* Superseded by AS/NZS ISO
** Classified to the B system of ISO standard
***Please note this consumable is not low hydrogen. Consumable is a high-deposition rate wire recommended for filling runs on non-critical welds only.
For detailed parts numbers, see page 19.
Weld consists of
“V” butt weld using
existing weld prep
Pro
gres
Bare Lip
Bucket Capacity Comparison
Sandvik Half Arrow
6
sive
wea
r
patt
ern
15 mm fillet
Bucket Capacity (tn)
5.5
5
Half Arrow lip assembly sectional view.
Typical Half Arrow wear pattern.
4.5
4
3.5
0
1000
2000
3000
4000
5000
6000
7000
By installing Sandvik’s Half Arrow weld-on lip system, the overall
integrity of an LHD bucket is kept in peak operating condition for
longer – resulting in higher production and improved penetration over
the life of the bucket.
Service Life (hrs)
14
15
Sandvik GET
weld-on heel shrouds
Mechanically attached GET systems parts lists
32 mm Series 2
Sandvik weld-on heel shrouds are highly effective in
reducing cost per tonne.
Strategically placed around the rim of the bucket,
Sandvik weld-on heel shrouds can dramatically extend
bucket life by significantly reducing damaging wear in the
heel area of the bucket.
Weld-on heel shrouds are available in four sizes to suit
any size loader:
• 190 x 40 mm
• 190 x 50 mm
• 250 x 50 mm
• 1100 x 40 mm.
When used in conjunction with Sandvik lip systems,
weld-on heel shrouds form an integral part of a complete
Sandvik bucket package.
The 190 mm wide heel shroud is specifically designed
for use by underground loaders.
Main features
• High wear life minimises costly downtime and bucket
rebuilds
• High strength, high hardness alloy provides high
resistance to wear
• Efficient design ensures maximum available wear
material and minimum throwaway material.
6
Supplier part number
Description
69039967
SBP32X250-S2
Sandvik GET 32 mm Series 2
(250 mm wide straight shroud)
69039968
SBP32X310-S2
Sandvik GET 32 mm Series 2
(310 mm wide straight shroud)
69039969
SBP32X380-S2
Sandvik GET 32 mm Series 2
(380 mm wide straight shroud)
69039970
SBP32X275-T2
Sandvik GET 32 mm Series 2
(275 mm wide transition shroud)
69039971
SBP32X210-CL2
Sandvik GET 32 mm Series 2
(210 mm wide left-hand corner shroud)
69039972
SBP32X210-CR2
Sandvik GET 32 mm Series 2
(210 mm wide right-hand corner shroud)
69042488
SBP32X210-CLH2
Sandvik GET 32 mm Series 2
(210 mm wide left-hand 3/4 corner shroud)
69042489
SBP32X210-CRH2
Sandvik GET 32 mm Series 2
(210 mm wide right-hand 3/4 corner shroud)
69039975
SBP32-PAS2
Sandvik GET 32 mm Series 2 pin assembly
69039976
SBP32-SKS2
Sandvik GET 32 mm Series 2 service kit
69039977
SBP32-CS2
Sandvik GET 32 mm Series 2 cap screw
69039978
SBP32-SS2
Sandvik GET 32 mm Series 2 spacer
69039979
SBP32-BP2
Sandvik GET 32 mm Series 2 bolt plug (pack of 50)
69039980
SBP32-B2
Sandvik GET 32 mm Series 2 weld-on boss
Picture
Standard 50 mm Series 2
For detailed parts numbers and properties, see page 19.
Bucket Capacity Comparison
Sandvik part number
Bare Lip
Sandvik Half Arrow
Sandvik part number
Supplier part number
Description
69039947
SBP50X290-S2
Sandvik GET 50 mm Series 2
(290 mm wide straight shroud)
69039948
SBP50X330-S2
Sandvik GET 50 mm Series 2
(330 mm wide straight shroud)
69039949
SBP50X420-S2
Sandvik GET 50 mm Series 2
(420 mm wide straight shroud)
69039950
SBP50X288-T2
Sandvik GET 50 mm Series 2
(288 mm wide transition shroud)
69039951
SBP50X235-CL2
Sandvik GET 50 mm Series 2
(235 mm wide left-hand corner shroud)
69039952
SBP50X235-CR2
Sandvik GET 50 mm Series 2
(235 mm wide right-hand corner shroud)
69039953
SBP50X235-CLH2
Sandvik GET 50 mm Series 2
(235 mm wide left-hand half corner shroud)
69039954
SBP50X235-CRH2
Sandvik GET 50 mm Series 2
(235 mm wide right-hand half corner shroud)
69039955
SBP50-PAS2
Sandvik GET 50 mm Series 2 pin assembly
69039956
SBP50-SKS2
Sandvik GET 50 mm Series 2 service kit
69039957
SBP50-CS2
Sandvik GET 50 mm Series 2 cap screw
69039958
SBP50-SS2
Sandvik GET 50 mm Series 2 spacer
69039959
SBP50-BP2
Sandvik GET 50 mm Series 2 bolt plug (pack of 50)
69039960
SBP50-B2
Sandvik GET 50 mm Series 2 weld-on boss
Picture
5.5
16
pacity (tn)
17
5
Mechanically attached GET systems parts lists
Weld-on GET systems parts lists
Heavy duty 50 mm Series 2
Sandvik heel shrouds
Sandvik part number
Supplier part number
Description
69039961
SBP50X290-SX2
69039962
Picture
Sandvik part number
Supplier part number
Description
Picture
Sandvik GET 50 mm Series 2
(290 mm wide heavy duty straight shroud)
69040160
SHS40X190-LHD
Small heel shroud
SBP50X330-SX2
Sandvik GET 50 mm Series 2
(330 mm wide heavy duty straight shroud)
69040888
SHS50X190-LHD
Standard LHD heel shroud
69039963
SBP50X420-SX2
Sandvik GET 50 mm Series 2
(420 mm wide heavy duty straight shroud)
69040887
SHS50X250-LHD
Large LHD heel shroud
69039964
SBP50X288-TX2
Sandvik GET 50 mm Series 2
(288 mm wide heavy duty transition shroud)
69042888
SHS40X1100-LHD
1100mm Long heel shroud
69039965
SBP50X235-CLX2
Sandvik GET 50 mm Series 2
(235 mm wide left-hand heavy duty corner shroud)
69039966
SBP50X235-CRX2
Sandvik GET 50 mm Series 2
(235 mm wide right-hand heavy duty corner shroud)
Sandvik part number
Supplier part number
Description
69037842
SHA180X1060
1060 mm long light duty half arrow wear edge
69037843
SHA320X800
800 mm long heavy duty half arrow wear edge
Sandvik half arrows
Sandvik protector strips
Picture
Picture
Sandvik part number
Supplier part number
Description
69041216
SPS50X600
600 mm long protector strip
69037844
SHA320X1150
1150 mm long heavy duty half arrow wear edge
69041217
SPS50X540
540 mm long protector strip
69038249
SHA320X350-HL
Heavy duty half arrow left-hand corner piece
69041218
SPS50X470
470 mm long protector strip
69038250
SHA320X350-HR
Heavy duty half arrow right-hand corner piece
69041220
SPS50-TLA
Taper lock assembly 50 mm protector strip
69040158
SHA180X280-L
Light duty half arrow left-hand corner piece
69041688
SPS50-RCS
Replacement cap screw (pack of 10)
69040159
SHA180X280-R
Light duty half arrow right-hand corner piece
69041219
SPS-MB
Mounting bracket, 50 mm protector strip
69042834
SPS-MBC
Curved mounting bracket, 50 mm protector strip
69042874
SPS50-BP
Plastic cap screw plug(bags of 100)
Sandvik GET profile bars
Sandvik cast corners
Picture
Sandvik part number
Supplier part number
Description
69037873
SPB1X290
Weld on profile bar to suit 50mm lip with 1 x 290mm wide
centre shroud
Picture
69037874
SPB1X420
Weld on profile bar to suit 50mm lip with 1 x 420mm wide
centre shroud
Sandvik part number
Supplier part number
Description
69039973
SCC32X155-LS
Sandvik GET 32 mm Series 2
left-hand cast corner
69037875
SPB2X290
69039974
SCC32X155-RS
Sandvik GET 32 mm Series 2
right-hand cast corner
Weld on profile bar to suit 50mm lip with 2 x 290mm wide
centre shroud
69037876
SPB2X330
69037854
SCC50X175-LS
Sandvik GET 50 mm Series 2
standard left-hand cast corner
Weld on profile bar to suit 50mm lip with 2 x 330mm wide
centre shroud
69037855
SCC50X175-RS
Sandvik GET 50 mm Series 2
standard right-hand cast corner
69037869
SCC50X175-LE
Sandvik GET 50 mm Series 2 extra
long left-hand cast corner
69037870
SCC50X175-RE
Sandvik GET 50 mm Series 2 extra
long right-hand cast corner
Materials properties
Properties for cast corners (alloy SS2000)
Sandvik GET tools
Yield strength (0.2% proof)
Tensile strength
Min. impact (20°)
444-495 HB
1430 MPa
1580 MPa
15 Joules
Properties for mechanically attached lip shrouds (alloy SS3000)
Sandvik part number
Supplier part number
Description
69042890
SBP-32TT
5/8 Hex key for Sandvik GET 32mm Series 2
69042891
SBP-50TT
19mm Hex key for Sandvik GET 50mm Series 2
69042892
STM-8812
Electronic digital thickness gauge
18
Hardness
Picture
Hardness
Yield strength (0.2% proof)
Tensile strength
Min. impact (20°)
477-534 HB
1580 MPa
1760 MPa
15 Joules
Properties for weld-on GET systems (alloy SS2000)
Hardness
Yield strength (0.2% proof)
Tensile strength
Min. impact (20°)
444-495 HB
1430 MPa
1580 MPa
15 Joules
19
Sandvik is a global industrial group with advanced products and
world-leading positions in selected areas – tools for metal cutting,
equipment and tools for the mining and construction industries,
stainless materials, special alloys, metallic and ceramic resistance
materials as well as process systems. In 2009, the Group had about
44,000 employees and representation in 130 countries, with annual
sales of nearly SEK 72,000 M.
Sandvik Mining and Construction is a business area within the
Sandvik Group and a leading global supplier of equipment, cementedcarbide tools, service and technical solutions for the excavation and
sizing of rock and minerals in the mining and construction industries.
Annual sales in 2009 amounted to about SEK 32,600 M, with
approximately 14,400 employees.
Sandvik Mining and Construction www.sandvik.com