60W Constant Current Mode LED Driver
F
110
M
M
SELV
IP67
■ Features
Constant Current mode output
Plastic housing with Class II design
Built-in active PFC function
Class 2 power unit
IP67 rating for indoor or outdoor installations
Function: 3 in 1 dimming
Typical lifetime>50000 hours
5 years warranty
( for 48V,54V only)
LPF-60D
series
( except for 48V,54V )
■ Applications
LED panel lighting
LED downlight
LED decorative lighting
LED tunnel lighting
Moving sign
■ Description
LPF-60D series is a 60W AC/DC LED driver featuring the constant current output. LPF-60D
operates from 90～305VAC and offers models with different rated voltage ranging between
12V and 54V. Thanks to the high efficiency up to 90%, with the fanless design, the entire
series is able to operate for -40 ℃ ~ +80 ℃ case temperature under free air convection. The entire
series is rated with IP67 ingress protection level and is suitable to work for a variety of applications
at dry, damp or wet locations. LPF-60D is equipped with the 3 in 1 dimming function so as to provide
the design flexibility for LED lighting system.
■ Model Encoding
LPF - 60D - 30
Rated output voltage(12V/15V/20V/24V/30V/36V/42V/48V/54V)
Rated wattage
Series name
File Name:LPF-60D-SPEC 2016-06-23
LPF-60D
60W Constant Current Mode LED Driver
series
SPECIFICATION
LPF-60D-12 LPF-60D-15 LPF-60D-20 LPF-60D-24 LPF-60D-30 LPF-60D-36 LPF-60D-42 LPF-60D-48 LPF-60D-54
MODEL
DC VOLTAGE
RATED CURRENT
RATED POWER
OUTPUT
CURRENT TOLERANCE
±5.0%
SETUP, RISE TIME Note.6
1000ms, 80ms / 115VAC
HOLD UP TIME (Typ.)
16ms/230VAC
Note.5
24V
2.5A
60W
30V
2A
60W
36V
1.67A
60.12W
42V
1.43A
60.06W
48V
1.25A
60W
54V
1.12A
60.48W
12 ~ 20V
14.4 ~ 24V
18 ~ 30V
21.6 ~ 36V
25.2 ~ 42V
28.8 ~ 48V
32.4 ~ 54V
90%
90%
90%
90%
46 ~ 54V
54 ~ 63V
59 ~ 66V
500ms, 80ms / 230VAC
16ms/115VAC
90 ~ 305VAC
127 ~ 431VDC
(Please refer to "STATIC CHARACTERISTIC" section)
47 ~ 63Hz
POWER FACTOR
PF≧0.97/115VAC, PF≧0.95/230VAC, PF≧0.92/277VAC@full load
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
TOTAL HARMONIC DISTORTION
THD< 20%(@load≧60%/115VC,230VAC; @load≧75%/277VAC)
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
EFFICIENCY (Typ.)
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
LEAKAGE CURRENT
OVER CURRENT
SHORT CIRCUIT
PROTECTION
OVER VOLTAGE
OVER TEMPERATURE
WORKING TEMP.
MAX. CASE TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
86%
88%
87%
0.8A / 115VAC
0.4A / 230VAC
89%
0.32A/277VAC
90%
COLD START 55A(twidth=270μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
8 units (circuit breaker of type B) / 14 units (circuit breaker of type C) at 230VAC
<0.75mA / 240VAC
95 ~ 108%
Constant current limiting, recovers automatically after fault condition is removed
Hiccup mode, recovers automatically after fault condition is removed.
15 ~ 17V
17.5 ~ 21V
23 ~ 27V
28 ~ 35V
34 ~ 40V
41 ~ 49V
Shut down o/p voltage, re-power on to recover
Shut down o/p voltage, re-power on to recover
Tcase=-40 ~ +80℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
Tcase=+80℃
20 ~ 95% RH non-condensing
-40 ~ +80℃, 10 ~ 95% RH
±0.03%/℃ (0 ~ 50℃)
VIBRATION
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY STANDARDS Note.8
UL8750, CSA C22.2 No. 250.0-08(except for 48V, 54V), ENEC EN61347-1, EN61347-2-13 independent, EN62384, IP67,
J61347-1, J61347-2-13 approved ; design refer to UL60950-1, TUV EN60950-1
SAFETY & WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMC
I/P-O/P:3.75KVAC
EMC EMISSION Note.8
I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
Compliance to EN55015,EN61000-3-2 Class C (@load≧60%) ; EN61000-3-3
EMC IMMUNITY
MTBF
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level (surge immunity Line-Line 2KV)
1202.9K hrs min. Telcordia SR-332 (Bellcore) ; 396.7Khrs min. MIL-HDBK-217F (25℃)
DIMENSION
162.5*43*32mm (L*W*H)
0.45Kg; 32pcs/15.4Kg/0.93CUFT
PACKING
NOTE
20V
3A
60W
FREQUENCY RANGE
AC CURRENT
INRUSH CURRENT(Typ.)
OTHERS
15V
4A
60W
9 ~ 15V
CONSTANT CURRENT REGION Note.2 7.2 ~12V
5.0% max. @rated current
CURRENT RIPPLE
VOLTAGE RANGE
INPUT
Note.5
12V
5A
60W
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2. Please refer to "DRIVING METHODS OF LED MODULE".
3. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
4. Tolerance : includes set up tolerance, line regulation and load regulation.
5. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.
7. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
8. The model certified for CCC(GB19510.14, GB19510.1, GB17743 and GB17625.1) is an optional model . Please contact MEAN WELL for details.
9. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch
without permanently connected to the mains.
10. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 70℃ or less.
11. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com
File Name:LPF-60D-SPEC 2016-06-23
LPF-60D
60W Constant Current Mode LED Driver
series
BLOCK DIAGRAM
fosc : 100KHz
I/P
EMI FILTER
&
RECTIFIERS
POWER
SWITCHING
PFC
CIRCUIT
RECTIFIERS
&
FILTER
+V
-V
DIM+
DIM-
O.L.P.
O.L.P.
PWM & PFC
CONTROL
DETECTION
CIRCUIT
O.V.P.
DRIVING METHODS OF LED MODULE
※ This series works in constant current mode to directly drive the LEDs.
In the constant current region, the highest voltage at the output of the driver
depends on the configuration of the end systems.
100
Vo(%)
Constant
Current area
Should there be any compatibility issues, please contact MEAN WELL.
60
(min.)
Hiccup
Protection
50
100
Io(%)
Typical output current normalized by rated current (%)
File Name:LPF-60D-SPEC 2016-06-23
LPF-60D
60W Constant Current Mode LED Driver
series
DIMMING OPERATION
※ 3 in 1 dimming function
AC/N(Blue)
AC/L(Brown)
+V(Red)
-V(Black)
DIM+(Blue)
DIM-(White)
LPF-60D
Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-:
1 ~ 10VDC, or 10V PWM signal or resistance.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.
Dimming source current from power supply: 1 0 0μA (typ.)
◎ Applying additive 1 ~ 10VDC
100%
-V
+
+
-
-
DIM+
+
Output current (%)
90%
+V
80%
70%
60%
50%
40%
Additive Voltage
-
30%
DIM-
20%
“DO NOT connect "DIM- to -V"
10%
1V
2V 3V 4V 5V 6V 7V 8V 9V 10V
Dimming input: Additive voltage
◎ Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
100%
-V
+
+
-
-
DIM+
Output current (%)
90%
+V
80%
70%
60%
50%
40%
Additive PWM signal
30%
DIM-
20%
“DO NOT connect "DIM- to -V"
10%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
Duty cycle of additive 10V PWM signal dimming input
◎ Applying additive resistance:
100%
-V
+
90%
+
-
-
DIM+
Additive Resistance
Output current (%)
+V
80%
70%
60%
50%
40%
DIM“DO NOT connect "DIM- to -V"
30%
20%
10%
10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N
(N=driver quantity for synchronized dimming operation )
Dimming input: Additive resistance
File Name:LPF-60D-SPEC 2016-06-23
LPF-60D
60W Constant Current Mode LED Driver
series
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL
for other options.
N
FG
L
Switch
Relay
Adjuster
10K/N~100K/N Ohms resistance
1~10V DC Voltage
10V PWM Signal
Green/
Yellow
Brown
Blue
AC/L
AC/N
LPF-60D
DIM+
DIMV(-)
V(+)
Blue
White
Black
Red
LED Lighting Fixture
Using a switch and relay can turn ON/OFF the lighting fixture.
File Name:LPF-60D-SPEC 2016-06-23
LPF-60D
60W Constant Current Mode LED Driver
series
OUTPUT LOAD vs TEMPERATURE
100
100
80
80
230VAC
Input only
60
60
LOAD (%)
50
LOAD (%)
230VAC
Input only
40
20
-40
-30
0
15
30
40
50
60
40
20
-40
70 (HORIZONTAL)
-30
-15
AMBIENT TEMPERATURE,Ta (℃)
0
15
30
50
65
80 (HORIZONTAL)
Tcase (℃)
STATIC CHARACTERISTIC
POWER FACTOR (PF) CHARACTERISTIC
※ Tcase at 70℃
100
90
0
0
0
0
0
0
0
0
0
80
PF
LOAD (%)
70
60
50
0
0
0
0
0
0
40
90
100
125
135
145
155 165
175
180
200
230
305
1
.9 9
.9 8
.9 7
.9 6
.9 5
.9 4
.9 3
.9 2
.9 1
0 .9
.8 9
.8 8
.8 7
.8 6
.8 5
.8 4
277VAC
230VAC
115VAC
50%
INPUT VOLTAGE (V) 60Hz
60%
70%
80%
90%
100%
(60W)
※ De-rating is needed under low input voltage.
LOAD
TOTAL HARMONIC DISTORTION (THD)
EFFICIENCY vs LOAD
THD
※ 48V Model, Tcase at 70℃
28%
26%
24%
22%
20%
18%
16%
14%
12%
10%
8%
6%
4%
2%
0%
277VAC
230VAC
115VAC
50%
60%
70%
80%
90%
100%
EFFICIENCY(%)
LPF-60D series possess superior working efficiency that up to 90% can
be reached in field applications.
※ 48V Model, Tcase at 70℃
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
277VAC
230VAC
115VAC
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD
LOAD
File Name:LPF-60D-SPEC 2016-06-23
LPF-60D
60W Constant Current Mode LED Driver
series
LIFE TIME
120
100
LIFETIME(Kh)
80
60
40
20
0
20
30
40
50
60
70
80
Tcase ( ℃ )
File Name:LPF-60D-SPEC 2016-06-23
LPF-60D
60W Constant Current Mode LED Driver
series
MECHANICAL SPECIFICATION
CASE NO.: LPF-60B
Unit:mm
162.5
300±20
3.6
ψ
tc
13
3.5
SJTW 18AWG×2C
3.6
43
ψ
AC/N(Blue)
AC/L(Brown)
3.5
300±20
60
Style 2464 18AWG×2C(+V,-V)
Style 2464 22AWG×2C(DIM+,DIM-)
+V(Red)
-V(Black)
DIM+(Blue)
DIM-(White)
: Max. Case Temperature
32
tc
3.5
3.5
INSTALLATION MANUAL
Please refer to : http://www.meanwell.com/webnet/search/InstallationSearch.html
File Name:LPF-60D-SPEC 2016-06-23
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Mean Well:
LPF-60D-12 LPF-60D-15 LPF-60D-20 LPF-60D-24 LPF-60D-30 LPF-60D-36 LPF-60D-42 LPF-60D-48 LPF-60D54