INSTALLATION INSTRUCTIONS MODEL 351 POWERGLIDE
DOOR CLOSERS HOLD OPEN ARMS WITH FUSIBLE LINK
351 NON SIZED ADJUSTABLE SIZES 1 THROUGH 6
COMPLIES WITH ADA REQUIREMENTS
FOR INSTALLATION ASSISTANCE CALL SARGENT AT 1-800-727-5477 • www.sargentlock.com
STANDARD & TOP JAMB APPLICATIONS
STANDARD APPLICATION
(TYPE 25-F ARM)
USE
PAGE 2
CLOSER MOUNTED ON
HINGE SIDE OF DOOR
DOOR WIDTH
(INCHES)
24
30
32
36
40
42
44
46
48
OVER 48
NUMBER OF TURNS OF SPRING POWER ADJUSTING SCREW
FROM FACTORY SETTING (USE CHART AS GUIDE ONLY)
INTERIOR DOORS
APPROXIMATE
EXTERIOR DOORS
DOOR WEIGHT (POUNDS)
FACTORY SET
80
110
1-4 CW
115
1-5 CCW
130
4-7 CW
150
155
7-10 CW
FACTORY SET
165
170
1-5 CW
10-12 CW
180
UP TO 18 CW AS REQ. 5 CW AND UP AS REQ.
*ADJUST SPRING POWER ACCORDING TO CHART*
NOTE: FOR F8 ARM MOUNTING
SEE DATA SHEET ENCLOSED
+
TOP JAMB APPLICATION
(TYPE 25-F, 25-FZ AND 25-FZA ARMS)
-
INCREASE
POWER
DECREASE
POWER
CLOCKWISE
(CW)
COUNTER CLOCKWISE
(CCW)
5/8" SPRING POWER
ADJUSTMENT NUT
LEFT
HAND DOOR
CLOSER MOUNTED ON FRAME
ON STOP SIDE OF DOOR
PULL
HINGE SIDE
STOP (PUSH) SIDE
PULL
HINGE SIDE
RIGHT
HAND DOOR
STOP (PUSH) SIDE
USE
PAGE 3
PARALLEL APPLICATION ONLY
PARALLEL ARM
APPLICATION
(TYPE 25-PF9 ARM)
CLOSER MOUNTED ON
STOP SIDE OF DOOR
USE
PAGE 4
DOOR WIDTH
(INCHES)
24
30
32
36
40
42
44
46
48
OVER 48
NUMBER OF TURNS OF SPRING POWER ADJUSTING NUT
FROM FACTORY SETTING (USE CHART AS GUIDE ONLY)
APPROXIMATE
INTERIOR DOORS
DOOR WEIGHT (POUNDS)
EXTERIOR DOORS
80
2-6 CW
110
115
6-8 CW
1-5 CCW
130
150
FACTORY SET
8-11 CW
155
165
170
11-13 CW
1-7 CW
180
UP TO 18 CW AS REQ. 8 CW AND UP AS REQ.
ADJUST SPRING POWER ACCORDING TO CHART*
*IF INTERIOR DOORS DO NOT HAVE TO COMPLY WITH ADA REQUIREMENTS, EXTERIOR DOOR SETTINGS ARE RECOMMENDED.
WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER AS NEEDED BY TURNING SPRING ADJUSTMENT SCREW CLOCKWISE.
IF NECESSARY, REDUCE SPRING POWER BY TURNING SCREW COUNTERCLOCKWISE.
Copyright © 2009, Sargent Manufacturing Company,
an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.
A7342A
1
351 STANDARD APPLICATION INSTRUCTIONS WITH FUSIBLE LINK
IMPORTANT: USE ALTERNATE MOUNTING IF DOOR CAN
OPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTING
ARM
TYPE
HOLD OPEN
ARM WITH
FUSIBLE
LINK
MOUNTING
MAX. DOOR
OPENING
DIM.
A
DIM.
B
STANDARD
110º
8 3/16"
11 7/16"
#12 x 3 WOOD
SCREWS OR
#12-24 X 2 1/4
FLAT HEAD
MACHINE SCREWS
DIM. "B"
SEE PAGE 6 FOR
MORTISE NUTS
DIM. "A"
ALTERNATE
135º
6 13/16"
1 1/8"
2"
10 1/6"
TOP OF DOOR
IF BUTT, FRAME AND WALL CONDITIONS PERMIT
DOOR WILL OPEN 180º
1
2
RIGHT HAND DOOR SHOWN. LEFT HAND
DOOR OPPOSITE.
2 1/2"
9/16"
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISE
NUTS WHEN REQUIRED. SEE PAGE 6 FOR MORTISE NUTS.
USE TEMPLATE A6753 FOR 25-OLC ARM
(LOW PROFILE)
A
9"
C OF HINGE PIVOT:
L
OFFSET PIVOTS, SWING CLEAR,
BUTTS,
CENTER HUNG OR INVISIBLE HINGES
INSTALL DOOR CLOSER TO DOOR WITH
SPRING ADJUSTMENT NUT AWAY FROM HINGE.
NOTE: 351 CLOSER BODIES ARE NON HANDED.
IT IS IMPORTANT THAT THE CLOSER BODY BE
MARKED WITH “RH” SYMBOL AT TOP, FOR RIGHT
HAND DOORS. “LH” SYMBOL AT TOP FOR LEFT
HAND DOORS.
RH
RIGHT HAND
DOOR SHOWN
B
ATTACH FOOT TO FRAME WITH PIVOT
AWAY FROM HINGE.
C
ATTACH ARM WITH INDEX MARK ON SPINDLE ALIGNED AS SHOWN. SECURE WITH SCREW AND
WASHER. INSERT ROD END INTO SWIVEL ARM AND TIGHTEN ARM SCREW AS SHOWN BELOW.
RIGHT HAND DOOR SHOWN (LEFT HAND DOOR OPPOSITE)
MAIN ARM
1
3
ROD
5
4
PIVOT
2
ARM
SCREW
90º
INDEX MARK
ON SPINDLE
POSITION OF
MAIN ARM WHEN
ASSEMBLING
TO SPINDLE
2
Copyright © 2009, Sargent Manufacturing Company,
an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.
A7342A
SWIVEL ARM
FUSIBLE LINK ARM ASSEMBLY SHOWN IS
HANDED. HAND OF ARM MUST BE THE
SAME AS HAND OF DOOR.
351 TOP JAMB APPLICATIONS INSTRUCTIONS
A
B
C
Copyright © 2009, Sargent Manufacturing Company,
an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.
A7342A
3
351 FUSIBLE LINK PARALLEL ARM APPLICATION INSTRUCTION
MAX. DOOR
OPENING
DIM.
A
DIM.
B
120º
9 7/8"
10 1/4"
C
L OF HINGE PIVOT
(BUTT HINGE SHOWN)
#12 x 3" WOOD SCREWS
OR #12-24 x 5/8 FLAT HEAD
MACHINE SCREWS
2 1/2"
5/16"
1 1/4"
DOOR
180º
7"
7 3/8"
TOP VIEW
1/2"
7/8"
1
LEFT HAND DOOR SHOWN. RIGHT HAND
DOOR DIMENSION OPPOSITE.
2
DO NOT USE THIS MOUNTING FOR
“SWING CLEAR” HINGES.
3
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
DIM. B
TOP OF
DOOR
DIM. A
2 3/8"
STOP
#12 X 3" WOOD SCREWS OR
#12-24 X 2 1/4" MACHINE
SCREW.
2 1/2"
DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISE
NUTS WHEN REQUIRED.
9"
SEE PAGE 6 FOR
MORTISE NUTS
CL OF HINGE PIVOT
A
INSTALL DOOR CLOSER TO FRAME WITH SPRING
ADJUSTMENT NUT AWAY FROM HINGE.
NOTE: 351 CLOSER BODIES ARE
NON HANDED. IT IS IMPORTANT
THAT THE CLOSER BODY BE MARKED
WITH “RH” SYMBOL AT TOP, FOR LEFT
HAND DOORS. “LH” SYMBOL AT TOP
FOR RIGHT HAND DOORS.
B
ATTACH FOOT BRACKET TO FRAME STOP.
RIGHT HAND
DOOR SHOWN
LH
C
USING WRENCH ON BOTTOM END OF SPINDLE, ROTATE 45º AND ASSEMBLE MAIN ARM TO CLOSER AS SHOWN, AND THEN INSERT ROD END INTO
SWIVEL ARM AND TIGHTEN ARM SCREW POSITIONING ARM 1 1/2" AWAY FROM DOOR.
LEFT HAND VIEW OF INDEX
POSITION OF MAIN ARM
WHEN ASSEMBLING
TO SPINDLE
PRELOAD
APPROX. 45º
INDEX MARK
ON SPINDLE
1
MAIN
ARM
5
RIGHT HAND DOOR
3
5
3
4
1 2
1 1/2"
MAIN ARM
CAUTION: DOOR CLOSER WILL NOT
OPERATE PROPERLY IF ARM IS NOT
INDEXED CORRECTLY.
4
MAIN ARM
ARM SCREW
SWIVEL ARM
Copyright © 2009, Sargent Manufacturing Company,
an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.
A7342A
INDEX MARK
ON SPINDLE
45º
2
45º
4
RIGHT HAND VIEW OF INDEX
FOOT BRACKET
FINAL ADJUSTMENT AND REGULATING PROCEDURE
DELAYED ACTION
RANGE
BACKCHECK
VALVE
CLOSING SPEED
RANGE
OPTIONAL DELAYED
ACTION VALVE
BACKCHECK
RANGE
LATCHING
SPEED RANGE
DOOR SPEED
VALVE
LATCHING
SPEED VALVE
REGULATING DOOR SPEED AND LATCHING SPEED AS NEEDED.
B
USE HEX SOCKET (1/8" ALLEN) WRENCH AND TURN VALVES CLOCKWISE
TO SLOW DOWN OR COUNTER CLOCKWISE TO SPEED UP DOOR
MOVEMENT.
FASTER
(+)
C
TO REGULATE THE INTENSITY OF BACKCHECK ACTION TURN VALVE
CLOCKWISE TO INCREASE OR COUNTER CLOCKWISE TO DECREASE
CHECKING.
CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. IT IS
DAMAGING TO THE CLOSER IF THE CHECKING ACTION IS TOO ABRUPT.
NEVER USE BACKCHECK AS A DOOR STOP.
ALWAYS USE A DOOR STOP TO STOP THE DOOR.
SLOWER
(–)
FOR MODELS WITH OPTIONAL DELAYED ACTION FEATURE
D
+
TURN VALVE CLOCKWISE TO SLOW DOWN OR COUNTER
CLOCKWISE TO SPEED UP DOOR MOVEMENT
F
ADJUSTMENT OF HOLD OPEN ARM
ADJUSTING FOOT FOR ADDITIONAL CLOSING POWER
(FOR STANDARD AND TOP JAMB APPLICATIONS ONLY)
MOVE FOOT
PIVOT TO HOLE
NEAREST HINGE
“DELAYED ACTION” PROVIDES SLOW DOOR CLOSING THROUGH
DELAYED ACTION RANGE
E
REGULATING BACKCHECK
+
HINGE EDGE OF DOOR
A
INSTALL COVER WITH TWO SCREWS AS SHOWN.
SLIGHT TIGHTENING OR LOOSENING OF HOLD OPEN NUT
CHANGES HOLDING POSITION OF DOOR.
NOTE: TO PROTECT WALL, TRIM AND CLOSER, USE A DOOR STOP
LOCATED 10∞ BEYOND HOLD OPEN POSITIONS BUT NOT BEYOND
THE MAXIMUM DOOR OPENING SHOWN ON INSTRUCTIONS.
USE 15/16"
WRENCH TO
ADJUST NUT
HOLD
OPEN NUT
INSERT IS REMOVABLE.
PLACE IN UNUSED OPENING.
Copyright © 2009, Sargent Manufacturing Company,
an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.
A7342A
5
USING MORTISE NUTS WITH SARGENT DOOR CLOSER
1. SEE INSTRUCTIONS OR DATA SHEET PACKED WITH DOOR CLOSER FOR DIMENSIONS LOCATING THE CLOSER BODY AND FOOT ON DOOR AND FRAME.
2. MORTISE NUT SHOWN IS DESIGNED FOR AN UNREINFORCED METAL DOOR.
3. FOR TOP JAMB AND CORNER BRACKET APPLICATIONS: THE DOOR CLOSER FOOT WILL BE ATTACHED TO THE DOOR IN A MANNER SIMILAR TO THAT
SHOWN FOR MOUNTING THE CLOSER BODY.
4. FOR DOORS 2 1/4" THICK: MORTISE NUT SHOWN FOR 1 3/4" THICK DOORS WILL BE FURNISHED ALONG WITH APPORPRIATE LENGTH THRU-BOLTS.
DOOR CONSTRUCTION MUST PROVIDE A BRIDGE TYPE REINFORCEMENT TO PREVENT THE DOOR RAIL FROM COLLAPSING WHEN THRU-BOLTS
ARE TIGHTENED.
SARGENT 1430
SERIES CLOSER
SHOWN. (OTHER
SERIES SIMILAR)
SEE NOTE #1 BELOW FOR DIMENSION
INFORMATION. IF A DIMENSION LESS THAN
7/8" IS USED. THE DOOR STOP MUST BE CUT
TO CLEAR THE MORTISE NUT HEAD OR THE
MORTISE NUT HEAD MUST BE RECESSED.
(SEE ENLARGED VIEW "Y")
FRAME
DOOR STOP
COVER
MORTISE NUT HEAD
DOOR
DRILL 1/4" DIA. HOLE
FOR MOUNTING SCREWS
DRILL 3/8" DIA.
HOLE FOR MORTISE
NUT BODY.
SARGENT 351 SERIES SHOWN
1/8"
SHORTEN MORTISE
NUT BODY TO
THIS LENGTH
5/8" DIA. HOLE
FRAME
DOOR
STOP
DOOR
351 DOOR CLOSER SHOWN
(TRACK ASSEMBLY
MOUNTING IS SIMILAR)
1/4" DIA.
DRILLED HOLE
#12-24 THREAD
MORTISE NUT
9/16"
DIA.
7/64"
1 11/16" FOR 1 3/4" THICK DOOR
1 5/16" FOR 1 3/8" THICK DOOR
(SEE NOTE #4 FOR 2 1/4" THICK DOORS)
6
Copyright © 2009, Sargent Manufacturing Company,
an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.
A7342A
VIEW "Y"
MORTISE NUT
HEAD
3/8" DIA. HOLE