QUICK START GUIDE: EASYMix12
Faders Buttons
System Design
Select between microphones 1-6 and 7-12.
Contact us for help with your system design or send us your site file for
review for proper operation of the EASYMix12 control surface.
Channel Buttons
Auto and Mute buttons are backlit. Use the Auto
button to add or remove a microphone input from
the automixer.
Faders
Use the faders to adjust the gain of the microphone.
The faders are motorized to allow for multipoint
control.
System Setup for Rane Hal DSP’s.
1. Setup your HAL DSP with the sample configuration file found at
www.easymix.net.
2. Navigate your browser to the IP address of the EASYMix12. The default IP
address is 192.168.0.205.
3. Click the Setup tab and enter the DSP IP Address, DSP Port, Control
System, and Communication Type as shown.
System Buttons
System buttons are backlit. Presets and system
configuration can be linked to these buttons.
EQ Buttons
EQ Buttons allow the faders to be used for individual
tone control on each input. Pressing HIGH changes
each fader to a high tone control for each
microphone. Pressing LOW changes each fader to a
low tone control for each microphone. The EQ
function reverts back to level controls after a preset
time. (10 seconds by default)
Power Switch
The Power switch provides contact closure to
control a power squencer or power control. The LED
is controlled by the power sequencer logic out to
indicate system power status. The Power switch
does not turn the EASYMix on or off.
4. Click Save.
5. Power cycle the EASYMix12.
6. Click the Test IO tab and check for communication with your HAL DSP.
Switch and LED input
Connect the Switch input to a power sequencer or
power control.
Connect the Led + and Led - to the logic output on
the power control. Observe correct polarity. An
internal jumper allows you to choose 5V, 12V, or 24V.
Default is 12V.
Power Input
Use the included 24VDC power supply to power the
EASYMix12. The shield should be connected to
ground through the power supply.
Montezuma
Sound
Montezuma Sound
PO Box 186
Montezuma, KS 67867
www.easymix.net
(620) 846-2633
QUICK START GUIDE: EASYMix12
Initial Setup
Controller Numbers
Channel
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
Control
Fader
Fader
Fader
Fader
Fader
Fader
Fader
Fader
Fader
Fader
Fader
Fader
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Mute
Mute
Mute
Mute
Mute
Mute
Mute
Mute
Mute
Mute
Mute
Mute
High Gain
High Gain
High Gain
High Gain
High Gain
High Gain
High Gain
High Gain
High Gain
High Gain
High Gain
High Gain
Signal
Signal
Signal
Signal
Signal
Signal
Type Control #
Level
1
Level
2
Level
3
Level
4
Level
5
Level
6
Level
7
Level
8
Level
9
Level
10
Level
11
Level
12
On/Off
13
On/Off
14
On/Off
15
On/Off
16
On/Off
17
On/Off
18
On/Off
19
On/Off
20
On/Off
21
On/Off
22
On/Off
23
On/Off
24
On/Off
25
On/Off
26
On/Off
27
On/Off
28
On/Off
29
On/Off
30
On/Off
31
On/Off
32
On/Off
33
On/Off
34
On/Off
35
On/Off
36
Meter
Meter
Meter
Meter
Meter
Meter
49
50
51
52
53
54
Channel
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
A
B
1
2
1
2
3
Control
Signal
Signal
Signal
Signal
Signal
Signal
Lo Shelf
Lo Shelf
Lo Shelf
Lo Shelf
Lo Shelf
Lo Shelf
Lo Shelf
Lo Shelf
Lo Shelf
Lo Shelf
Lo Shelf
Lo Shelf
Hi Shelf
Hi Shelf
Hi Shelf
Hi Shelf
Hi Shelf
Hi Shelf
Hi Shelf
Hi Shelf
Hi Shelf
Hi Shelf
Hi Shelf
Hi Shelf
Button
Button
Button
Button
Button
Button
Button
Button
LED
LED
LED
LED
LED
LED
LED
LED
Control In
Control In
Logic Out
Logic Out
Status LED
Status LED
Status LED
Type Control #
Meter
55
Meter
56
Meter
57
Meter
58
Meter
59
Meter
60
Level
61
Level
62
Level
63
Level
64
Level
65
Level
66
Level
67
Level
68
Level
69
Level
70
Level
71
Level
72
Level
73
Level
74
Level
75
Level
76
Level
77
Level
78
Level
79
Level
80
Level
81
Level
82
Level
83
Level
84
On/Off
85
On/Off
86
On/Off
87
On/Off
88
On/Off
89
On/Off
90
On/Off
91
On/Off
92
On/Off
93
On/Off
94
On/Off
95
On/Off
96
On/Off
97
On/Off
98
On/Off
99
On/Off
100
105
106
107
New units ship with an IP address of 192.168.0.205. Enter this IP address in
a browser to log into the web interface. The web interface will allow you to
change the unit IP address and DSP IP address. Various other settings can
also be modified.
The EQ timeout determines the amount of time before the EQ function will
revert back to the normal mix mode. Time is in seconds.
You can program the system buttons to be either latched or momentary by
typing a value next to the corresponding button. Use 0 for latched.
Momentary is programmed by entering a time value in ms. You can also
change the status of the LED by choosing Reg or Inv.
Backup and System Settings
You can backup your system settings by inserting a flash drive into the USB
port and then pressing the bottom “system” button while powercycling the
unit. This saves a file named EASYMIX.txt to the flash drive. Open this file to
review the saved unit settings. This is also a good way to obtain the IP
address used to access the web interface.
Example:
EasyMix IP 192.168.0.205
DSP IP 192.168.0.215
DSP Port 48630
EQ on time 10
Minimum loop 100
Momentary buttons
#1 0
#2 500
#3 500
#4 0
#5 0
#6 0
#7 0
#8 0
Fader cals
1 Zero 405
2 Zero 405
3 Zero 405
4 Zero 405
5 Zero 405
6 Zero 405
Thirty 70
Thirty 70
Thirty 70
Thirty 70
Thirty 70
Thirty 70
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
Montezuma
Sound
Montezuma Sound
PO Box 186
Montezuma, KS 67867
www.easymix.net
(620) 846-2633