Anti fouling
Sea Hawk is manufacturer of premium performance antifouling paints and coatings for over 38 years.It was
established in 1978 and is dedicated to bringing only the highest quality products to today’s mariner.
Sea Hawk paints are made with care and attention to every detail. Every gallon is inspected before it leaves their
facility to ensure that it meets their stringent quality control requirements.
Sea hawk product selection chart
Boat type
Fiberglass
Wood
Hull
Primer S-76
New
Tuff Stuff
Primer 1277
Boat length (Feet)
Paints
(Islands 44, 77,
99, Talon)
New hull
Not applicable
2-3 Coats
Not applicable
2-3 Coats + 1 coat
at water line
Previously painted
hull- light sand
Not applicable
Not applicable
1-2 Coats (optional)
1-2 Coats + 1 coat
at water line
Previously painted
hull- heavy sand
Not applicable
2-3 Coats
Not applicable
2-3 Coats + 1 coat
at water line
New hull
Not applicable
Not applicable
1-2 Coats (optional)
2-3 Coats + 1 coat
at water line
Previously painted
hull
Not applicable
Not applicable
1-2 Coats (optional)
2-3 Coats + 1 coat
at water line
1-2 coats
2-3 Coats
Not applicable
2-3 Coats + 1 coat
at water line
Previously painted
hull- light sand
Not applicable
Not applicable
Not applicable
2-3 Coats + 1 coat
at water line
Previously painted
hull- heavy sand
1-2 coats (optional)
New hull
Steel &
Aluminium
Amount of paint needed per coat
1-2 Coats
Not applicable
2-3 Coats + 1 coat
at water line
Per Coat
20-25
3 Quarts
25-30
1 Gallon
30-32
1 Gallon + 1 Quart
33-37
1 Gallon + 2 Quarts
38-40
1 Gallon + 3 Quarts
41-42
2 Gallons
43-44
2 Gallons + 1 Quart
45-46
2 Gallons + 2 Quarts
47-49
2 Gallons + 3 Quarts
50-52
3 Gallons
53-55
3 Gallons + 1 Quart
56-59
3 Gallons + 2 Quarts
*Amounts are estimates and may vary by boat
and bottom paint applied. Please see product
technical data sheets for exact coverage.
Islands 44 Plus GL - Self cleaning copolymer antifoulant, TBT-Based
Islands 44 Plus was developed for the harshest tropical environments in the world. Islands 44 Plus is
a multi-seasonal self polishing paint. It has a high load of copper and tin that will ensure maximum
protection against marine growth.
Boat care
Features and Benefits
• Self-cleaning copolymer with high load of tin (TBT) and copper
• The only tin (TBT) paint available on the market
• Highest level of antifoulant protection available
• Highest quality grade of cuprous oxide available (more potent active ingredient)
13
Product Information
Finish/Sheen
Converter
Copper Content
Volume Solids
Solids by Weight
Mix Ratio
Flash Point
VOC
Film Thickness
Recommended Coats
Theoretical Coverage:
Application data
Mixing
Induction time
Pot life
Brush/rolling
Airless spray
1162
Conventional Spray:
Safety
Application controls
Gloss
:: Brush, roller or spray
Method
One Pack
Induction/ Sweat-in Time :: Not Applicable
47%
:: Not Applicable
Pot Life
51% ± 2%
74%
Part number Colour Size
One Pack
80ºF/27ºC
Black
1 Gallon
13.04.0023
452 Grams/Liter
Blue
1 Gallon
13.04.0024
5 mils wet equals 2.55 dry per coat
2 heavy coats on entire hull and 3 at
Overcoating Interval - Drying Time (Hrs)
waterline and other high wear areas
Substrate temp.
Touch
Min
Max recoat
Launch minimum
:: 320 sq.ft./gal. @ recommended film
thickness
73°F (23°C)
3 hr
1 hr
N/A
N/A
::
::
::
::
::
::
::
::
::
::
95°F (35°C)
1 hr
1 hr
N/A
12 hrs
:: Islands 44 antifouling paint contains a moderate concentration of copper oxide and may have settled in transit.
Product must be thoroughly mixed with power mixer/shaker until uniform.
:: N/A
:: Not Applicable
:: Solvent Resistant Roller Cover 3⁄8” pile (nap), smooth to medium. Prewash roller cover to remove loose fibers
prior to use.
:: Minimum 33:1–2 GPM ratio pump; “0.017-0.026" orifice tip; 3⁄8" ID high-pressure material hose; 90 PSI line
pressure; 60 mesh filter.
:: Please contact Exalto Emirates for more specific information.
:: Prior to use, obtain and consult the "Material Safety Data Sheet" of this product for health and safety
information. Read and observe all precautionary notices on container labels.