Assembly instruction for Conen height adjustable column system.
Packing unit PY-…
left
column
Handle columns with care!
Unpack the columns slowly!
right
column
Packing unit PY-…
1.
2x floor panel
left floor panel
right floor panel
4x 8mm dowel
4x sheet metal screw 5x55
2.
2x z-holder
3.
2x slide
4.
2x 8mm washer
2x selflocking nut M8
5.
4x 8mm washer
4x selflocking nut M8
Packing unit PY-…
center of system
61,75 cm
7 cm
61,75 cm
123,5 cm
3,5 cm
1.
left floor panel
2x floor panel
4x 8mm dowel
4x sheet metal screw 5x55
3 cm
center of
floor panel
right floor panel
Mark the center of the System at the floor or the wall.
Mark the center of the floor panel.
Attention! Left and right floor panel are different.
Center of system to center of floor panel 61,75 cm.
Mark at floor and wall.
The distance from the center of one floor panel to the other must be exactly 123,5 cm.
Distance from wall to floor panel 7 cm.
Mark the four holes.
Use a 8mm drill.
Use a drill suitable for the floor.
Use 2x 8mm dowel and 2x sheet metal screw 5x55 per floor panel.
Use four z-holders in case of floor heating (not included).
Packing unit PY-…
Center of z-holder
2. 2x z-holder
No fittings for wallmounting
included.
210 cm – 240 cm
Mark center of z-holder.
Center of z-holder must be situated exactly above middle of floor panel.
Use a water level.
Attach the z-holder 210 cm – 240 cm above the ground.
Mark position of z-holder.
Fix z-holder with suitable wallmounting material according to the consistence of the wall.
Ask wallmounting specialist.
No fittings for wallmounting included.
The wallmounting specialist has to decide wether 4 z-holder or a load distribution panel has to be
used (not included).
Packing unit PY-…
3. 2x slide
After fixing the floor panels put the two pylons in front of the panels carefully.
Use the nut M8 and 8mm washer.
Tighten the nut a little.
Attach the slides to the pylons.
Packing unit PY-…
Packing unit PY-…
4. 2x washers M8
2x selflocking nutM8
Put the column to the wall.
Fix the slide with the z-holder.
Washer has to be situated between z-holder and nut M8.
Packing unit AF-PY…
6.
4x Allen head screw M8x20
4x 8mm washer
4x Allen head lense screw with flange
M6x20
4x 6mm washer
7.
4x Allen head screw M8x45
4x 8mm washer
4x Allen head screw M6x45
4x 6mm washer
8.
1x hexagon head screw M8x100
2x 8mm washer
1x nut M8
Packing unit AF-PY…
5.
4x 8mm washer
4x selflocking nut M8
Attach the adapter frame to the slides at the columns.
Use 4x selflocking nut M8 and 4x 8mm washer.
Packing unit AF-PY…
800mm
710mm
600mm
400mm
Fix rail at the back of the television
According to model use 2-4x Allen head
screw M8x20 and washer
or
2-4x Allen head lense screw with flange
6.
M6x20 and washer.
2-4x Allen head screw M8x20 and
2-4x 8mm washer
or
2-4x Allen head lense screw with flange M6x20 and
2-4x 6mm washer
Packing unit AF-PY…
Hang in the television with rail at the
spare outs of the frame. Make sure, that
the television is placed exactly in the
centre of the system. The rail has to hang
1. hang rail in
in the front of the spare out at the frame.
2. bring it to
the front
Packing unit AF-PY…
Picture without television
Packing unit AF-PY…
Packing unit AF-PY…
7.
2-4x Allen head screw M8x45 and
2-4x 8mm washer
or
2-4x Allen head screw M6x45 and
2-4x 6mm washer
Picture without television
Fix television to the traverse at the frame to secure it.
According to model use 2-4x Allen head screw M8x45 and washer
or
2-4x Allen head screw M6x45 and washer.
Packing unit AF-PY…
Packing unit AF-PY…
Picture without television
Attach upper bar (only for use for systems with wings) and lower bar to the frame.
Packing unit WBW…
9.
12x sheet metal screw 4,2x25
10.
4x rubber buffer
Packing unit WBW…
9.
12x sheet metal screw 4,2x25
Fix wings with 3 sheet metal screws to each hinge. (Only for use for systems with wings.)
Packing unit WBW…
10.
4x rubber buffer
8.
1x hexagon head screw M8x100
2x 8mm washer
1x nut M8
Adjust wings via the long slots in the upper and lower bar. Use 4x black buffer to protect the frame of
the television. (Only for use for systems with wings.)
Fix weight panels to the lower bar of the frame. Use 1x hexagon head screw M8x100, 2x 8mm washer
and 1x nut M8.