Positioning Switches -Non Contact-
Do not use this product as a detection
device for human body protection.
(For human body protection, use products compliant with the local laws and regulations
such as OSHA, ANSI, and IEC)
-Overview-
Contact Switches -Non Contact Point Type-Bolt / Flat / 2-SignalCAD Data Folder Name: 30_Sensors
QFeature
QBolt
MSNCB
MSNC
(Degree of Protection IP67) MSNCBD (With LED) MSNCD (With LED)
- The contact type switch can detect objects in given positions regardless of material and color.
- Non contact structure utilizing the magnet detection IC (Hall effect element).
- Able to detect with low contact force.
L2
L1
100
22
R3
QBasic Structure
d
7
.5
When the contact shaft strokes, the magnet moves and the hall effect element outputs a signal.
SR
Rubber Seal
(1) Contact Part
(2) Spring
(3) Magnet
(4) Hall Effect Element IC
(5) Housing
M Material
Contact Part Thread
SUS303
(2)
(3)
(4)
(5)
Power supply voltage
Current consumption
Operating Temp.
Dielectric strength
Withstand voltage
Vibration resistance
Part Number
DC5~24V
10mA or less
0~60°C
10MΩ (DC250V Based on Megohm-meter)
AC500V 50/60Hz, 1 min. between each terminal and case
10~55Hz, Stroke of 1.5mm in Respective X, Y, Z Direction
Stroke
1.2
Operating
Point
M8x0.75
1.4
1
14
901
0.4
4
20
2
2.5
15
0.7
5
30
2.6
3
22
3
L2
d
SR
Mass
(g)
Unit Price Volume Discount Rate Unit Price Volume Discount Rate
Qty. 1~9
10~19
Qty. 1~9
10~19
856
1,106
1,047
765
724
970
920
901
856
1,106
1,047
4.5
22.5
7.5
7.5
11
5.5
SR3
(2-Signal Type)
Brown
DC
DC
5~24V
Detection Circuit 1
Red Orange
Detection Circuit 2
Load 1
Blue
0V
LED Lamp
Although the switches are intended to be trouble-free, incorporate a redundant safety measure such as a duplex circuit to avoid a serious accident or spread of
damage caused by a malfunction or failure of the switch.
QDesign Precautions
- Contact Angle
- The object contact angle to the switch should be within ±2°.
- Stroke
- Do not force the contacts beyond the end of the stroke.
Provide a stopper if necessary.
Relief
- Do not apply any force that will cause rotation of the contact.
- Effects of magnetic field
- Do not use the switch in a strong magnetic field. A magnetic field over 1000 gauss will cause the switch to malfunction.
QWiring Precautions
- Reverse polarity connection prohibited
- Connect the wires correctly in accordance with the circuit diagram. Never connect the power supply in reversed polarity.
- Driving relays
- When a relay (under 12mA) is driven, connect a reversed diode in parallel.
LED Lamp
ON in Operation
Type
Stroke
MSNCF
MSNCFD
3
Operating
Point
Contact
Force
N
Mass
(g)
0.5 from Tip
(Repeatability 0.02)
0.5
17
M Material
Contact Part Case
Zinc Alloy
7
Cable
Cable 1m, 3-Conductors Ø2.8, Oil Resistant
Min. Bending Radius R7
MSNCF
Unit Price Volume Discount Rate
Qty. 1~9
10~19
1,047
992
MSNCFD
Unit Price Volume Discount Rate
Qty. 1~9
10~19
1,252
1,188
EFor orders larger than indicated quantity, please request a quotation.
Q Feature: Operating point can be freely selected within setting range by turning adjusting screw with precision slotted screwdriver (1.6mm in edge width).
Q2-Signal
MSNCWD (With LED)
(Degree of Protection IP65)
Rubber Boot
Adjustment Screw (M1.2x0.25)
59
36.5
SR1.5
100
33
8.5
LED Lamp
ON in Operation
M14x0.5
(Stroke) 6
QCautions on Installation
- Cable failure at inlet
- Do not apply excessive stress to the cable inlet of the switch case, the solders of cable could be damaged resulting in signal output failures.
- If the cable is not fixed, fasten at appropriate midway points to avoid strains on cable inlet.
- Nut tightening torque
- Tighten M6 under 1Nm. Tighten M8 and M14 under 2.7Nm.
R3
QFlat
Load 2
Part Number
Blue
Switch
Ø2.2
SUS303
5~24V
Detection Circuit
DC
Black
22
9
Relay
Black
Red
Brown
100
.5
15.5
12.4
10
(Connected with relay, etc.)
2-Ø3.5
Ø6
QPrecautions for Use
18.5
Ø7
5~24V
Blue
2.4
QFlat
MSNCF
(Degree of Protection IP65) MSNCFD (With LED)
Brown
Detection Circuit
0.3
0.5 from Tip
(Repeatability 0.02)
QSchematics
Load
Black
L1
EFor orders larger than indicated quantity, please request a quotation.
25°C
Not provided
Vertical (Without declination)
1 time/sec.
(Connected with sequencer, etc.)
MSNCB / MSNC MSNCBD / MSNCD
Contact
Force
N
M6x0.5
1.5
MSNC
MSNCD
* Subject to the following conditions
Endurance Test Conditions
Operating Temp.
Vibrations
Contact Angle
Operation Frequency
Type
MSNCB
MSNCBD
MxP
(Fine)
7
25mA or less
1.5/3/6
0.02 or less
NO (Normally Open)
0.1 or Less
10 Million Times or More
1msec. or less
NPN Open Collector
Without LED: MAX15mA
With LED: MAX12mA
3
Stroke
Repeatability
Contact Mechanism
Hysteresis
Service Life*
Frequency Response
SUS303
QBolt
QRatings and Environmental Resistance
QSpecifications
AAccessories
Cable
Cable 1m, 3-Conductors Ø2.8, Oil Resistant
Hexagon Nuts 2 pcs.
Min. Bending Radius R7
(M6 Thickness 2, Wrench Size 7M8 Thickness 2.5, Wrench Size 10)
3 3
(1)
LED Lamp
7
ON in Operation
MxP
MMaterial
Contact Part Thread
SUS303
SUS303
Cable
AAccessories
Cable 1m, 4-Conductors Ø3, Oil Resistant Min. Bending Radius R7 Hexagon Nuts 2 pcs. (Thickness 3 Wrench Size 17)
Q2-Signal
Part Number
Type
No. of Signals
MSNCWD
2
Stroke
6
Contact Force N Operating Point Mass Unit Price
(g) Qty. 1~9
min. max. Setting Range
0.5
1.5
0.5~4
(Repeatability 0.02)
60
3,276
MSNCWD
Volume Discount Rate
10~19
3,113
EFor orders larger than indicated quantity, please request a quotation.
Part Number
MSNC1.5
1 -1783
5
D P.87
NG
OK
NG
1 -1784