STEEL PIPE CLAMPS
Fig. 212
Medium Pipe Clamp
Size Range: 1⁄2" through 30"
Material: Carbon steel
Finish: q Plain or q Hot-Dip Galvanized with Zinc Plated Bolts & Nuts
Service: Recommended for suspension of cold pipe lines or hot lines where no insulation is required.
Maximum Temperature: Plain 750° F, Galvanized 450° F
Approvals: C
omplies with Federal Specification A-A-1192A (Type 4) WW-H-171-E (Type 4), ANSI/MSS SP-69
and MSS SP-58 (Type 4). UL, ULC Listed and FM Approved (Sizes 3⁄4" - 8").
C
F
Installation: Normally used with weldless eye nut Fig. 290 or eye rod.
Features:
D
• Clamps tightly to pipe.
E
G
• Wide range of sizes.
CL
• Equal gap design on many sizes.
Ordering: S pecify pipe size, figure number, name and finish.
B
H
Note: The “C” gap dimension ensures adequate clearance at the top attachment
point for a weldless eye nut or other appropriate rod attachment. This gap may
or may not be present on the bottom portion of the clamp. If different loads or
Note: This picture is representative of a typical Figure 212. Distance
dimensions are required, refer to Fig. 42 SD non-standard two bolt pipe clamp.
between clamp ears beneath pipe may or may not be equal to upper gap.
FIG. 212: LOADS (LBS) • WEIGHT (LBS) • DIMENSIONS (IN)
Pipe
Size
Span
Ft.
Max Load
For Service Temp
650° F
7*
9*
10*
11*
12*
13*
14*
16*
17*
19*
22*
23*
20
15
15
12
12
9
500
–
800
1,040
B
0.29
0.33
0.35
0.38
0.43
1.10
1.20
1.40
1.50
1.80
2.60
5.40
6.50
13.60
15.20
20.50
22.30
31.60
35.80
53.10
113.90
1
C
750° F
1
⁄2
3
⁄4
1
11⁄4
11⁄2
2
21⁄2
3
31⁄2
4
5
6
8
10
12
14
16
18
20
24
30
Weight
930
1,615
1,440
2,490
2,220
3,060
2,730
3,500
3,360
11⁄8
7
1 ⁄16
19⁄16
21⁄8
25⁄8
27⁄8
33⁄16
31⁄2
43⁄16
47⁄8
6
77⁄16
87⁄16
91⁄4
101⁄4
115⁄8
123⁄4
151⁄4
19
1
⁄2
5
⁄8
3
⁄4
11⁄4
1
11⁄8
11⁄4
13⁄8
15⁄8
2
Rod
Take Out
E
13⁄16
11⁄4
13⁄8
15⁄8
111⁄16
21⁄8
25⁄8
27⁄8
33⁄16
31⁄2
43⁄16
47⁄8
6
77⁄16
87⁄16
91⁄4
101⁄4
115⁄8
123⁄4
151⁄4
19
H
D
117⁄32
123⁄32
125⁄32
129⁄32
25⁄32
27⁄32
23⁄4
31⁄4
31⁄2
313⁄16
41⁄4
415⁄16
53⁄4
67⁄8
89⁄16
99⁄16
105⁄8
115⁄8
13
141⁄8
167⁄8
211⁄8
121⁄32
131⁄32
23⁄32
23⁄4
31⁄4
31⁄2
313⁄16
41⁄4
415⁄16
53⁄4
67⁄8
89⁄16
99⁄16
105⁄8
115⁄8
13
141⁄8
167⁄8
211⁄8
F
G
Width
5
⁄16
1
1
⁄2
5
11/4
3
11/2
⁄8
⁄4
7
⁄8
1
11⁄8
11⁄4
13⁄4
2
21/2
3
4
Clamps may be furnished with square ends. “Span” represents the maximum recommended distance between hangers on a continuous & straight run of horizontal standard weight steel pipe filled with
water. In all cases, verify that chosen location of hangers does not subject hangers to a load greater than the maximum recommended load shown above. For vapor service, the presence of fittings or
insulation, and other weights and types of pipe, spans may either increase or decrease. In all cases, verify that chosen location of hanger does not subject hangers to a load greater than the maximum
recommended load shown. *Indicates that span represents the maximum span for water filled pipe.
PROJECT INFORMATION
APPROVAL STAMP
Contractor:
q Approved
q Approved as noted
q Not approved
Engineer:
Remarks:
Project:
Address:
Submittal Date:
Notes 1:
Notes 2:
PH-1.15