ROPE MARKER
CM3/B
MACHINE FOR
MEASURING,
MARKING,
AND CUTTING
ROPES.
Clipping Machines
Net Testing Equipments
Net Sewing Machines
Rope Machines
Zip Fastener for marine use
Dryer Machines
Single Phase V
Hz
Power W
Dimensions cm L x W x H
Net Weight kg
220
50
600
216 x 60 x 190
300
Our Buraschi Rope Marker CM3/B is a special machine allowing
to make measurements, two-colour staining and hot cutting
the ropes both straight and oblique, with great precision.
The Buraschi Rope Marker CM3/B can be used with ropes of
8 mm diameter up to 25 mm (0.31 in up to 1.00 in) and
allows, thanks to a sophisticated software program, to record
and store a wide range of these executions and automatically
repeat them as many times as you want. The cuts are made
with absolute precision, and in a short time you will lower your
working time considerably. You will also avoid different and
inaccurate outcomes of measuring, marking and cutting your
ropes.
Equipped with wheels, the Buraschi Rope Marker CM3/B can
be moved wherever it is needed in your plant. It is perfectly
able to work with coils of 250 m and to continue working at the
end of the coil with a simple splicing with the new coil without
losing data, and maintaining the accuracy and precision of the
work program to be executed.
The Buraschi Rope Marker CM3/B is easy to use and once you
have started the program you have chosen, it works without the
need for an operator. When the program ends a beeping sound
will alert you to proceed with a new execution of your choice.
The BURASCHI two-colour staining process will allow you to
easily identify the various pieces to be cut, cutting them in
large quantities as needed and making inventories of various
sizes cut. This saves time and labour costs. And it is all done
with absolute precision!
Moreover, the Buraschi Rope Marker CM3/B allows to easily
establish a precise program for each type of order to perform
and to store the file for any order. Programs can then be loaded
to repeat the process as needed.
ROPE PROCESS TIME ON CM3/B
We have done some trials and following are the related
process time which will give you an idea about the
performance of the machine.
OPERATOR SCREEN
No operator is needed during the working cycle.
The test was made on twisted rope of 18 mm polysteel.
•
•
•
How long does it take to measure one rope 20 m long and to add 6 marks with single colour on each piece?
Time needed 64”
How long does it take to measure one rope 5 m long and to add 6 marks with single colour?
Time needed 29”
How long does it take to measure one rope 30 m long ?
Time needed 65”
Test made on 1 complete coil of rope 220 m long, cut into
19 ropes 10.8 m long and marked 5 times on each piece,
and 4 ropes 2.4 m long with 5 marks each.
Time needed for all the job 25 minutes without operator
standing by.
TECHNICAL DATA
• Transmission pulley and brake at 1,800 mm height
from the ground
• Powered pulley coated with rubber
• Idle pulley for pneumatic contrast
• Electronic meter with instrument for setting marking
cycles
• Inerasable bicolors marker
• Rope feeding speed from 5 to 30 m/minute
• Air compressor
• Knot sensor and rope end sensor
• Frame with locking feet and wheels
• Hot cutter system and smoke vacuum
• PC serial port
• Voltage: 220 - 240 V single phase
MARKING
CUTTING
DEVICE FOR ADJUSTING THE ANGLE
OF THE CUTTING
STRAIGHT CUT
COLOURING WITH TWO DIFFERENT COLOURS
AND SIZES ACCORDING TO THE NEEDS OF THE
CUSTOMER.
ANGLE CUT
YESTERDAY
TODAY
ROPE
MARKER
TIME IS MONEY.
SAVE YOUR TIME
WITH US!
Headquarters:
BURASCHI ITALIA SRL
Via dei Tigli 7/9 - 20853 BIASSONO MILAN ITALY
Tel.: +39 039 23 24 142 - Fax: +39 039 24 99 865
email: [email protected]
Sale and Service Area: CHILE & SOUTH America:
BURASCHI CHILE LTDA.
Panamericana Norte Km. 12 lote 22 - CASTRO - CHILOÉ CHILE
Tel.: +56 65 2 52 66 73 - Fax: +56 65 2 52 66 20
Cell.: +56 9 988 68 497
e-mail: [email protected]
www.buraschiitalia.com