Mounting heights
Central locking Spare Parts
It is critical that the load of the bed
sits on the mounting washer. This
reduces movement of the product
over time and reduces the stress
placed on the attachment bolts and
holes. If the load of the bed doesn’t
sit on the washer, with time the
mounting bolt holes will elongate and
the castor will push up into the leg
and cease to function.
Central locking
Central Locking Bed Requirements
This page outlines the requirements needed to ensure that your
Fallshaw centre locking castors function correctly when initially
fitted and also continue to function for the life of the product. If
Squareto
adaptor
to suit
28mmofI.D
tuberequirements please
you are unable
meet one
or more
these
Code:
SPMCLNS28SPLIT
speak to our
technical
team to see if a special product can be
Central
locking castors must be installed with a tight fit
made to Note:
suit your
application.
into the tubing – otherwise the castors will tilt forward under
load causing excessive wear and compromising the
directional lock performance. Our warranty only applies if
castors are correctly installed. This includes always fitting the
central
locking castors using round tubing or square tubing
Mounting
heights
with square adaptors.
It is critical that the load of the bed
sits on the mounting washer. This
reduces movement of the product
control pedal
Central
Bed ended
Requirements
over
time andLocking
reduces theDouble
stress
placed on the attachmentSPPEDCL(L)
bolts and - Left hand side
SPPEDCL(R)
holes. If the load of the bed
doesn’t - Right hand side
sitThis
onpage
the washer,
the
outlineswith
thetime
requirements
needed to ensure that your
mounting
holes
will elongate
and
Fallshaw bolt
centre
locking
castors function
correctly when initially
the
castor
push
up intotothe
leg for the life of the product. If
fitted
andwill
also
continue
function
and
to function.
youcease
are unable
to meet one or more of these requirements please
Glass
filled nylon
transmission
lever product can be
speak to our
technical
team
to see if a special
Very
strong,
hard polymer designed for high abrasion
made to suit
your
application.
It is therefore
important
to ductility
control the
height from
the bottom of the
resistance
and
to prevent
brittle-fracture.
tube to theNote:
attachment
alsometal
to thetransmission
hex bar holelevers
(see
tougherholes,
than and
sintered
drawing forcodes:
dimension
and tolerances).
SPMCLTL
– to suit the standard long ISO pintle
These dimensions are
to suit –the
Australian
and
European Standard
SPMCSTL
to suit
the short
pintle
(EN12531:1999).
If you are unable meet these dimensions please
Mounting heights
speak to our sales team.
It is critical that the load of the bed
Hex
Bar
sits on
theClearance
mounting washer. This
reduces movement of the product
Itover
is also
critical
the hex
for actuating the castor is free to
time
andthat
reduces
the bar
stress
move.
Ensure
that
the frame bolts
does and
not interfere with the hex bar. This
placed
on the
attachment
involves
drilling
large
holes
for ample clearance (suggest 18mm
holes. Ifeither
the load
of the
bed
doesn’t
diameter)
if smaller
sit on the or,
washer,
withholes
time are
the required. Ensure that all the holes are
aligned
andbolt
theholes
frame
is elongate
strong enough
mounting
will
and that it will not twist when fully
loaded.
the castor will push up into the leg
and cease to function.
The hex bar should only contact
the mechanism (two castors,
It is therefore
to control the height from the bottom of the
pedals
and theimportant
transmission
tube to
the attachment
lever),
it should
be able toholes, and also to the hex bar hole (see
drawing
for without
dimension
and tolerances).
rotate
freely
rubbing
or
These
dimensions
are
to
the I.D
Australian
bending.
If adaptor
these holes
aresuit
too
Square
to suit
28mm
tube and European Standard
(EN12531:1999).
If you
unable meet these dimensions please
small,
or misaligned,
theare
rubbing
Code:
SPMCLNS28SPLIT
speak
toCentral
our of
sales
team.
and
bending
the
hex bar
Note:
locking
castors must be installed with a tight fit
will make
operation
into the
tubing – difficult,
otherwise the castors will tilt forward under
and
willBar
stop
the castors
from
Hex
Clearance
load
causing
excessive
wear and compromising the
functioning.
directional lock performance. Our warranty only applies if
It iscastors
also critical
that the installed.
hex bar for
the castor
is free
are correctly
Thisactuating
includes always
fitting
the to
move.
Ensure
thatcastors
the frame
does
nottubing
interfere
with thetubing
hex bar. This
central
locking
using
round
or square
involves
either adaptors.
drilling large holes for ample clearance (suggest 18mm
with square
diameter) or, if smaller holes are required. Ensure that all the holes are
aligned and the frame is strong enough that it will not twist when fully
loaded.
Double ended control pedal
SPPEDCL(L)
The hex bar should only
contact- Left hand side
SPPEDCL(R)
the mechanism (two
castors, - Right hand side
pedals and the transmission
lever), it should be able to
rotate freely without rubbing or
bending. If these holes are too
small,
or misaligned,
the
rubbingStandard
Glass
filled nylon
transmission
lever pintle
Ø 27.8
andVery
bending
of the
hex
bar designed for high abrasion
strong,
hard
polymer
11/8"
will make
operation
difficult,to prevent brittle-fracture.
resistance
and ductility
andNote:
will stop
the castors
from
tougher
than sintered
metal transmission levers
functioning.
codes: SPMCLTL – to suit the standard long ISO pintle
SPMCSTL – to suit the short pintle
It is therefore important to control the height from the bottom of the
tube to the attachment holes, and also to the hex bar hole (see
drawing for dimension and tolerances).
These dimensions are to suit the Australian and European Standard
(EN12531:1999). If you are unable meet these dimensions please
speak to our sales team.
Central Locking
It is therefore important to control the height from the bottom of the
tube to the attachment holes, and also to the hex bar hole (see
drawing for dimension and tolerances).
These dimensions are to suit the Australian and European Standard
(EN12531:1999). If you are unable meet these dimensions please
speak to our sales team.
Hex Bar Clearance
It is also critical that the hex bar for actuating the castor is free to
move. Ensure that the frame does not interfere with the hex bar. This
involves either drilling large holes for ample clearance (suggest 18mm
diameter) or, if smaller holes are required. Ensure that all the holes are
aligned and the frame is strong enough that it will not twist when fully
loaded.
The hex bar should only contact
the mechanism (two castors,
pedals and the transmission
lever), it should be able to
rotate freely without rubbing or
Short Pintle
bending. If these holes are too
(made to order)
small, or misaligned, the rubbing
and bending of the hex bar
will make operation difficult,
and will stop the
castors from
31.8
functioning.
Note: Standard configuration for hospital beds with 4
castors is a set of 2 DL and 2 TB castors. A set includes 2
transmission pedals with 3 positions; DL, swivel (free) and TB.
kg/lb
Diameter
x Width
mm / inch
Precision
Q Ball
100kg
220lb
100x32
4 x 1 1/4
Precision
Q Ball
100kg
220lb
125x32
5 x 1 1/4
100kg
220lb
150x32
6 x 1 1/4
Precision
Q Ball
Precision
Q Ball
100kg
220lb
200x32
8x 1 1/4
150
6
100
4
125
5
150
6
100
4
125
5
150
6
100
4
125
5
150
6
100
4
125
5
150
6
100
4
125
5
150
6
Mount Height
139
5 1/2
165
6 1/2
190
7 1/2
139
5 1/2
165
6 1/2
190
7 1/2
139
5 1/2
165
6 1/2
190
7 1/2
139
5 1/2
165
6 1/2
190
7 1/2
139
5 1/2
165
6 1/2
190
7 1/2
139
5 1/2
165
6 1/2
190
7 1/2
Swept Radius
91
3 9/16
103
4 1/16
113
4 5/16
91
3 9/16
103
4 1/16
113
4 5/16
91
3 9/16
103
4 1/16
113
4 5/16
91
3 9/16
103
4 1/16
113
4 5/16
91
3 9/16
103
4 1/16
113
4 5/16
91
3 9/16
103
4 1/16
113
4 5/16
Tyre Material
MJQ100G
SET
MJQ125G
SET
QTQ150G
150x32
6 x 1 1/4
Twin Wheel
Polyurethane (PU)
Wheel Options
100kg
220lb
Swivel
/CZL
SET
QTQ200G
SET
N/A
Precision
Q Ball
52
2-3/64"
125
5
TPE
kg / lb
34
100
4
Grey Rubber
Capacity
Single wheel
Bearing
Type
1-5/16"
Fork Size
Castor Type
Single
or
Twin
Wheel
Fork Options
1-1/4"
7
19
3/4"
18
• Excellent design and performance
It is critical that the load of the bed
sits on the mounting washer. This
reduces movement of the product
over time and reduces the stress
placed on the attachment bolts and
holes. If the load of the bed doesn’t
sit on the washer, with time the
mounting bolt holes will elongate and
the castor will push up into the leg
and cease to function.
1/4"
• Precision wheel bearings
Mounting heights
97
cwt
nue
od
pr
18
Glass filled nylon transmission lever
CentralVery
locking
castors
strong, hard
polymer designed for high abrasion
resistance
ductility
to one
prevent
brittle-fracture.
• Used on
hospitaland
beds
where
pedal
Note: tougher than sintered metal transmission levers
SPMCLTL
– to suitbrakes
the standard long ISO pintle
needs codes:
to activate
multiple
SPMCSTL – to suit the short pintle
3 13/16"
Central Locking castors
The hex bar should only contact
the mechanism (two castors,
pedals
and the
This page
outlines
thetransmission
requirements needed to ensure that your
lever),
it should
becastors
able tofunction correctly when initially
Fallshaw
centre
locking
freely
without
fitted rotate
and also
continue
torubbing
functionorfor the life of the product. If
bending.
too of these requirements please
you are
unableIftothese
meetholes
one are
or more
misaligned,
thetorubbing
speaksmall,
to ourortechnical
team
see if a special product can be
bending
of the hex bar
madeand
to suit
your application.
will make operation difficult,
and will stop the castors from
functioning.
SET
MJQ100G/CZL
Total brake
/CZLTB
MJQ100G/CZLTB
Direction Lock
Swivel
/CZLDL
/CZS
MJQ100G/CZLDL
MJQ100G/CZS
Bed Set 2x TB + 2 x DL + 2 x Transmission levers MJQ100GCLLSET
MJQ125G/CZL
MJQ125G/CZLTB
MJQ125G/CZLDL
Bed Set 2x TB + 2 x DL + 2 x Transmission levers MJQ125GCLLSET
QTQ150G/CZL
QTQ150G/CZLTB
QTQ150G/CZLDL
Bed Set 2x TB + 2 x DL + 2 x Transmission levers QTQ150GCLLSET
QTQ200G/CZL
QTQ200G/CZLTB
QTQ200G/CZLDL
Bed Set 2x TB + 2 x DL + 2 x Transmission levers QTQ200GCLLSET
CUQ150GT/CNL
CUQ150GT/CNLTB
CUQ150GT/CNLDL
Bed Set 2x TB + 2 x DL + 2 x Transmission levers CUQ150GTCLLSET
specialized
Double ended control pedal
SPPEDCL(L) - Left hand side
SPPEDCL(R) - Right hand side
79
8
specialized
Square adaptor to suit 28mm I.D tube
Code:
SPMCLNS28SPLIT
Glass filled
nylon transmission lever
Note:
Centralhard
locking
castors
must befor
installed
with a tight fit
Very strong,
polymer
designed
high abrasion
into
the tubing
otherwise
the castors
will tilt forward under
resistance
and–ductility
to prevent
brittle-fracture.
load
wearmetal
and compromising
the
Note:causing
tougherexcessive
than sintered
transmission levers
directional
lock performance.
Our warranty
onlypintle
applies if
codes: SPMCLTL
– to suit the standard
long ISO
castors are
correctly
This includes
always fitting the
SPMCSTL
– to installed.
suit the short
pintle
central locking castors using round tubing or square tubing
with square adaptors.
3 1/8"
Double ended control pedal
SPPEDCL(L) - Left hand side
SPPEDCL(R) - Right hand side
Central Locking Bed Requirements
specialized
18
specialized
Square adaptor to suit 28mm I.D tube
Code: SPMCLNS28SPLIT
Note: Central locking castors must be installed with a tight fit
into the tubing – otherwise the castors will tilt forward under
load causing excessive wear and compromising the
directional lock performance. Our warranty only applies if
castors are correctly installed. This includes always fitting the
central locking castors using round tubing or square tubing
with square adaptors.
It is also critical that the hex bar for actuating the castor is free to
move. Ensure that the frame does not interfere with the hex bar. This
involves either drilling large holes for ample clearance (suggest 18m
diameter) or, if smaller holes are required. Ensure that all the holes ar
aligned and the frame is strong enough that it will not twist when full
loaded.
specialized
Central locking Spare Parts
Central locking
Central locking
Central locking Spare Parts
Hex Bar Clearance
Total Brake
Direction Lock
MJQ100G/CZSTB
MJQ100G/CZSDL
Bed Set 2x TB + 2 x DL + 2 x Transmission levers MJQ100GCLSSET
MJQ125G/CZS
MJQ125G/CZSTB
MJQ100G/CZSDL
Bed Set 2x TB + 2 x DL + 2 x Transmission levers MJQ125GCLSSET
QTQ150G/CZS
QTQ150G/CZSTB
QTQ150G/CZSDL
Bed Set 2x TB + 2 x DL + 2 x Transmission levers QTQ150GCLSSET
QTQ200G/CZS
QTQ200G/CZSTB
QTQ200G/CZSDL
Bed Set 2x TB + 2 x DL + 2 x Transmission levers QTQ200GCLSSET
CUQ150GT/CNS
CUQ150GT/CNSTB
CUQ150GT/CNSDL
Bed Set 2x TB + 2 x DL + 2 x Transmission levers CUQ150GTCLSSET
19
Tel: (03) 9359 2955
Tel: (03) 9359 4355
www.castorsgalore.com.au
Castors Galore General Bearing & Industrial Supplies