27/06/2016 11:00 Example and Guidelines for a DASR 145 MAINTENANCE ORGANISATION EXPOSITION SAMPLE EXPOSITION EXPLANATORY STATEMENT This document provides guidance on the structure and content of an approved maintenance organisation (AMO) exposition as required by DASR 145.A.70. The content relates directly to the requirements of DASR 145 and is based on the example of Exposition contents shown in AMC 145.A.70(a) The document is a mixture of requirements and guidance under recommended headings for an AMO’s exposition. It is recommended that AMOs retain the headings (expanded as necessary) and the content of Part 1. All other detail can be amended to suit your organisation. The content of the sample exposition has been arranged into parts, sections and subsections. The aim is to collate all the processes and procedures related to a subject under the relevant section in the exposition, irrespective of the location of the regulatory requirement in DASR 145. The text provided under each section or subsection of the sample exposition provides guidance on the nature of contents to be included. The sections and subsections should be further expanded according to the complexity of the processes and procedures of the AMO. As mentioned above, DGTA-ADF recommends Part 1 be retained as per the sample exposition as it provides the main administrative information about the organisation, including the organisation’s structure, location, scope of approval, list of key personnel etc. In some cases specimen text or procedures have been included (in italics) in the sample exposition to expand the guidance and to illustrate the nature of the content required. The organisation should carefully consider the provided content and make necessary changes before including it in their exposition. It is important for the users of this document to appreciate that no single sample exposition can meet the needs of all types and sizes of organisations or reflect the different organisational structures, policies and procedures. This document is for guidance only and the structure and content of the AMO’s exposition should reflect their structures, policies and procedures. DGTAADF suggests the organisation correlates the content of the exposition with a compliance check list/matrix to demonstrate to DGTA-ADF that they have fully addressed all applicable requirements of DASR 145. The remainder of the document, Parts 2 to 5 inclusive, comprises subject and suggested paragraph headings, to form the basis of an acceptable document. Where the content of the exposition requires processes and procedures to be provided, these may be included in other documents provided they are referred to in the exposition. However, in that case, the other documents form part of the exposition and are subject to the same requirements and controls as the exposition. Processes and procedures included or referred to in the exposition should be of adequate depth and include enough details to demonstrate they establish compliance with the applicable requirements of DASR 145. An accurately completed compliance matrix may benefit the AMO as a component of their Quality Management System for checking and conducting audit compliance requirements. Duties and responsibilities of individuals as mentioned in the exposition should relate to the obligation of the organisation or the individual under DASR 145, and are not meant to cover employment conditions, performance criteria or administrative functions. Where content of the exposition requires identifying the individual responsible for an action or a decision that is part of a process, it is intended that the individual will be identified by their position title (such as ‘Quality Manager’) or if applicable, by means that describes their function (such as ‘Safety Manager’ or ‘Data Entry Clerk’). AMO Sample Exposition June 2016 Page i Where content of the exposition deals with records to be created or kept by the organisation, the relevant procedures in the exposition should take into account the following: legibility of the record; retrieval of records; and protection of the records from loss, damage or accidental alteration. DGTA-ADF recommends worksheets, checklists, forms, lists of items and personnel etc. required under the exposition or associated with the processes or procedures required by the exposition should be included as appendices at the end of the exposition. However, as mentioned above, they may be included in other documents that contain the processes and procedures or in any other document if it is convenient for the organisation to do so. ADDITIONAL INFORMATION Additional guidance in completion of the following DASR 145 MOE topics can be found in the documents referenced below: Structure and content of an MOE – Refer to EASA Foreign Part 145 Approvals – User Guide for Maintenance Organisation Exposition – UG.CAO.00024.004 MOE 1.3 Management Personnel and DASR Form Four Instructions – Refer to EASA Work instruction WI.CAO.00115.003 MOE 1.6 Certifying Employees – Refer EASA User Guide for Foreign Part 145 Approvals – Aircraft certifying staff and support staff – UG.CAO.00121‐003 MOE 1.6 Certifying Employees – Refer EASA User Guide for Foreign Part 145 Approvals – Aircraft type training – UG.CAO.00122‐003 MOE 1.6 Certifying Employees – Refer EASA User Guide for Foreign Part 145 Approvals – Component, Engine and APU certifying staff – UG.CAO.00126‐003 MOE 1.6 Certifying Employees – Refer EASA User Guide for Foreign Part 145 Approvals – Demonstration of 6/24 months maintenance experience – UG.CAO.00128‐003 MOE 1.7 Manpower Plan – Refer EASA User Guide for Foreign Part 145 Approvals – Definition of maintenance organisations staff number – UG.CAO.00120‐003 MOE 1.9 Scope of Work – Refer EASA User Guide for Foreign Part 145 Approvals – Aircraft Line Maintenance – UG.CAO.00134‐003 MOE 1.9 Scope of Work – Refer EASA User Guide for Foreign Part 145 Approvals – Composite repair workshop – UG.CAO.00135‐003 MOE 1.9.6 Fabrication In the course of maintenance – Refer EASA User Guide for Foreign Part 145 Approvals – Parts fabrication – UG.CAO.00131‐001 MOE 2.4 Tools and Equipment – Refer EASA User Guide for Foreign Part 145 Approvals – Tools & Equipment – UG.CAO.00132‐001 Use the link below to access the above documents https://www.easa.europa.eu/easa‐and‐you/aircraft‐products/continuing‐airworthiness‐ organisations/foreign‐part‐145‐organisations AMO Sample Exposition June 2016 Page ii ANYBODY’s DASR 145 EXPOSITION Insert Organisation Logo here ANYBODY'S DASR 145 MAINTENANCE ORGANISATION EXPOSITION This exposition has been developed to meet the Defence Aviation Safety Regulation (DASR) 145 Maintenance Organisation Exposition (MOE) requirements AMO approval certificate reference number xxxxx Anybody’s Aerospace Limited Address 1 Address 2 Address 3 Telephone: xx xxxxxxx Facsimile: xx xxxxxxxx Email: [email protected] Copy Number: x of xx Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Holder Name: Page 0 of 52 ANYBODY’s DASR 145 EXPOSITION TABLE OF CONTENTS ADDITIONAL INFORMATION...................................................................................................II AMENDMENT RECORD............................................................................................................5 DISTRIBUTION LIST .................................................................................................................6 ABBREVIATIONS, ACRONYMS AND DEFINITIONS ...............................................................7 PART 1 GENERAL ...............................................................................................................8 1.1 CORPORATE COMMITMENT BY THE ACCOUNTABLE MANAGER........................8 1.2 SAFETY AND QUALITY POLICY ................................................................................9 1.3 MANAGEMENT PERSONNEL ..................................................................................10 1.4 DUTIES AND RESPONSIBILITIES OF MANAGEMENT PERSONNEL....................11 1.4.1 ACCOUNTABLE MANAGER .......................................................................11 1.4.2 RESPONSIBLE MANAGER .........................................................................11 1.4.3 QUALITY MANAGER ...................................................................................12 1.4.4 SAFETY MANAGER ....................................................................................13 1.4.5 OTHER RELEVANT PERSONNEL..............................................................13 1.5 MANAGEMENT ORGANISATION CHART................................................................14 1.6 CERTIFYING STAFF .................................................................................................15 1.6.1 BASE CERTIFYING STAFF.........................................................................15 1.6.2 LINE CERTIFYING STAFF (MECHANICAL/AVIONIC)................................15 1.6.3 COMPONENT CERTIFYING STAFF (DASR FORM 1) ...............................15 1.6.4 BASE MAINTENANCE (CATEGORY B1 AND B2 QUALIFIED SUPPORT) STAFF ..........................................................................................................15 1.7 MANPOWER RESOURCES ......................................................................................17 1.7.1 BASE MAINTENANCE / COMPONENT MAINTENANCE ...........................17 1.7.2 LINE MAINTENANCE .................................................................................17 1.7.3 SPECIALISED ACTIVITIES ........................................................................17 1.7.4 SUB-CONTRACTED SERVICES................................................................17 1.8 FACILITIES ................................................................................................................18 1.8.1 BASE MAINTENANCE.................................................................................18 1.8.2 LINE MAINTENANCE ..................................................................................18 1.8.3 COMPONENT MAINTENANCE ...................................................................18 1.8.4 LOCATIONS OTHER THAN THOSE LISTED IN THE EXPOSITION..........18 1.9 SCOPE OF WORK.....................................................................................................19 1.9.1 AIRCRAFT MAINTENANCE ........................................................................19 1.9.2 ENGINE MAINTENANCE.............................................................................19 1.9.3 COMPONENT MAINTENANCE ...................................................................19 1.9.4 SPECIALIST MAINTENANCE......................................................................19 1.9.5 ADDITIONAL SIGNIFICANT ACTIVITIES....................................................19 1.9.6 FABRICATION IN THE COURSE OF MAINTENANCE ...............................20 1.10 CHANGES TO THE ORGANISATION.......................................................................20 1.10.1 SIGNIFICANT CHANGES ............................................................................20 1.10.2 MINOR CHANGES.......................................................................................20 1.11 EXPOSITION AMENDMENT PROCEDURES ...........................................................21 1.11.1 EXPOSITION MANAGEMENT.....................................................................21 1.11.2 CHANGES TO AMO EXPOSITION..............................................................21 PART 2 2.1 MAINTENANCE PROCEDURES..........................................................................22 SUPPLIER EVALUATION AND SUBCONTRACT CONTROL PROCEDURE ..........22 Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 1 of 52 ANYBODY’s DASR 145 EXPOSITION 2.2 ACCEPTANCE / INSPECTION OF AIRCRAFT COMPONENTS AND MATERIALS FROM OUTSIDE CONTRACTORS ...........................................................................22 2.3 STORAGE, TAGGING AND RELEASE OF COMPONENTS AND MATERIALS ......23 2.4 ACCEPTANCE OF TOOLS AND EQUIPMENT.........................................................23 2.5 CALIBRATION OF TOOLS AND EQUIPMENT .........................................................23 2.6 USE OF TOOLING AND EQUIPMENT BY STAFF....................................................23 2.7 CLEANLINESS STANDARDS OF MAINTENANCE FACILITIES ..............................24 2.8 MAINTENANCE INSTRUCTIONS AND RELATIONSHIP TO AIRCRAFT/ AIRCRAFT COMPONENT MANUFACTURERS’ INSTRUCTION INCLUDING UPDATING AND AVAILABILITY TO STAFF .........................................................................................24 2.9 REPAIR PROCEDURES............................................................................................24 2.10 AIRCRAFT MAINTENANCE PROGRAMME COMPLIANCE.....................................25 2.11 AIRWORTHINESS DIRECTIVES PROCEDURE ......................................................25 2.12 OPTIONAL MODIFICATION PROCEDURE ..............................................................25 2.13 MAINTENANCE DOCUMENTATION ........................................................................25 2.14 TECHNICAL RECORDS CONTROL .........................................................................25 2.15 RECTIFICATION OF DEFECTS ARISING DURING BASE MAINTENANCE ...........26 2.16 CERTIFICATION OF MAINTENANCE AND CERTIFICATE OF RELEASE TO SERVICE PROCEDURES .........................................................................................26 2.17 RECORDS FOR THE CAMO.....................................................................................26 2.18 OCCURRENCE REPORTING TO DGTA-ADF/CAMO/MTCH/STC HOLDER...........26 2.19 RETURN OF DEFECTIVE AIRCRAFT COMPONENTS TO STORE ........................28 2.20 DEFECTIVE AIRCRAFT COMPONENTS TO OUTSIDE CONTRACTORS..............28 2.21 CONTROL OF COMPUTER MAINTENANCE RECORDS SYSTEM ........................28 2.22 MAN-HOURS PLANNING..........................................................................................28 2.23 CONTROL OF CRITICAL TASKS..............................................................................28 2.24 SPECIFIC PROCEDURES ........................................................................................28 2.25 PROCEDURES TO DETECT AND RECTIFY MAINTENANCE ERRORS ................29 2.26 SHIFT/TASK HANDOVER PROCEDURES...............................................................29 2.27 PROCEDURES FOR NOTIFICATION OF MAINTENANCE DATA INACCURACIES, INCOMPLETENESS AND AMBIGUITIES TO DGTA-ADF/CAMO/MTCH/STC HOLDER ....................................................................................................................29 2.28 PRODUCTION PLANNING PROCEDURES .............................................................30 PART L2 ADDITIONAL LINE MAINTENANCE PROCEDURES .........................................31 L2.1 LINE MAINTENANCE CONTROL OF AIRCRAFT COMPONENTS, TOOLS, EQUIPMENT, ETC.....................................................................................................31 L2.2 LINE MAINTENANCE PROCEDURES RELATED TO SERVICING / FUELLING / DEICING ETC. ................................................................................................................31 L2.3 LINE MAINTENANCE CONTROL OF DEFECTS AND REPETITIVE DEFECTS......32 L2.4 LINE PROCEDURE FOR COMPLETION OF TECHNICAL LOG ..............................32 L2.5 LINE PROCEDURE FOR POOLED PARTS AND LOAN PARTS..............................32 Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 2 of 52 ANYBODY’s DASR 145 EXPOSITION L2.6 LINE PROCEDURE FOR RETURN OF DEFECTIVE PARTS...................................32 L2.7 LINE PROCEDURE FOR CONTROL OF CRITICAL TASKS ....................................32 PART 3 QUALITY AND SAFETY MANAGEMENT PROCEDURES .................................34 3.1 QUALITY MANAGEMENT SYSTEMS .......................................................................34 3.2 QUALITY AUDIT OF ORGANISATION PROCEDURES ...........................................34 3.3 QUALITY AUDIT OF AIRCRAFT AND COMPONENTS ............................................34 3.4 QUALITY AUDIT REMEDIAL ACTION PROCEDURE ..............................................35 3.5 CERTIFYING STAFF – QUALIFICATIONS AND TRAINING ....................................35 3.6 CERTIFYING STAFF RECORDS ..............................................................................35 3.7 QUALIFICATION OF QUALITY AUDIT PERSONNEL ..............................................35 3.8 QUALIFICATION OF MAINTENANCE SUPERVISORS............................................36 3.9 QUALIFICATION OF MAINTENANCE PERSONNEL ...............................................36 3.10 AIRCRAFT OR COMPONENT MAINTENANCE TASKS, DEVIATION PROCESS CONTROL..................................................................................................................36 3.11 CONCESSION CONTROL FOR DEVIATION FROM THE ORGANISATION'S PROCEDURES ..........................................................................................................36 3.12 QUALIFICATION PROCEDURE FOR SPECIALISED ACTIVITIES SUCH AS NDT, WELDING ETC. .........................................................................................................36 3.13 CONTROL OF MANUFACTURER'S AND OTHER MAINTENANCE WORKING TEAMS .......................................................................................................................36 3.14 HUMAN FACTORS TRAINING PROCEDURE ..........................................................37 3.15 COMPETENCE ASSESSMENT OF PERSONNEL ...................................................37 3.16 SAFETY MANAGEMENT SYSTEM (SMS)................................................................37 PART 4 OPERATIONS .......................................................................................................38 4.1 CONTRACTING/TASKING CAMO ............................................................................38 4.2 CAMO PROCEDURES AND DOCUMENTATION .....................................................38 4.3 CAMO RECORDS COMPLETION .............................................................................39 PART 5 TRAINING AND ASSESSMENT...........................................................................40 5.1 FACILITIES ................................................................................................................40 5.2 PERSONNEL .............................................................................................................40 5.3 TRAINING AND ASSESSMENT PROCEDURES......................................................40 5.4 TRAINING SOURCING AND QUALITY CONTROL ..................................................41 5.5 AUTHORISATION AND REPORTING .......................................................................41 5.6 RECORDS .................................................................................................................41 PART 6 APPENDICES .......................................................................................................42 6.1 SAMPLE OF DOCUMENTS.......................................................................................42 6.2 LIST OF SUBCONTRACTORS..................................................................................42 6.3 LIST OF LINE MAINTENANCE LOCATIONS ............................................................42 6.4 LIST OF CONTRACTED DASR 145 ORGANISATIONS ...........................................43 Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 3 of 52 ANYBODY’s DASR 145 EXPOSITION 6.5 COMPLIANCE MATRIX .............................................................................................44 List of Effective Pages This section should include the list of effective pages of the complete manual. The list may be prepared in the following manner. Page No. Revision Date Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page No. Revision Date Page 4 of 52 ANYBODY’s DASR 145 EXPOSITION AMENDMENT RECORD This section should set out the amendment record of the exposition. The amendment record may be in the following form. Amendment Date No. Amendment Details Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Amended by Date of Inclusion Page 5 of 52 ANYBODY’s DASR 145 EXPOSITION DISTRIBUTION LIST This section should include a distribution list to ensure proper distribution of the exposition and to demonstrate to DGTA-ADF that all employees involved in maintenance have access to the relevant information. This does not mean that all employees have to be in receipt of a complete exposition but that a reasonable number of copies are distributed within the organisation so that employees may have quick and easy access to this exposition. Alternately, if the manual is available electronically this section should set out how the electronic version is available throughout the organisation and to individuals outside the organisation. Distribution list. Copy No. Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Holder Page 6 of 52 ABBREVIATIONS, ACRONYMS AND DEFINITIONS This section should set out the meaning of any abbreviations, acronyms and unique terms used in the exposition. For example: AD AMO AMP ARC CAMO CoA CRS DASA DASR MAOC MEL Airworthiness Directive Approved Maintenance Organisation Aircraft Maintenance Programme Authorised Release Certificate Continuing Airworthiness Management Organisation Certificate of Airworthiness Certificate of Release to Service Defence Aviation Safety Authority Defence Aviation Safety Regulations Military Air Operator's Certificate Minimum Equipment List Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 7 of 52 PART 1 GENERAL 1.1 CORPORATE COMMITMENT BY THE ACCOUNTABLE MANAGER (DASR 145.A.70(a)1, GM 145.A.70(a)) The Accountable Manager's exposition statement should include the intent of the following paragraph. The following statement may be used without amendment. Any changes to the statement should not alter the intent. This statement is a copy of the text detailed in GM 145.A.70(a) 9. I, the Accountable Manager have the corporate authority to ensure that all maintenance services required by the customer can be financed and provided to the standard required and that all necessary resources are available to ensure compliance with this exposition. I will establish and promote policies for safety management and quality systems for this AMO and its employees in accordance with this exposition. This exposition defines the procedures upon which the DASR 145 approval of [organisation name] as an AMO is based as required by DASR 145.A.70. The exposition, along with the procedures contained in it, are approved by DGTA-ADF and must be complied with as applicable, in order to ensure that all the activities involving the provision of maintenance services including maintenance of aircraft and components is provided to the standard required by DGTA-ADF. The procedures included or referred to in this exposition do not override the necessity of complying with any new or amended regulations published by DGTA-ADF from time to time where these new or amended regulations are in conflict with these procedures. The AMO approval will continue whilst DGTA-ADF is satisfied that these procedures are being followed. DGTA-ADF reserves the right to suspend, vary or cancel the AMO approval of the organisation, as applicable, if DGTA-ADF has evidence that the procedures are not being followed and the standards are not being upheld. Signed: ………………………………………… Date: ……………………………. Name: ………………………………………….. Title: Accountable Manager,……………….[Organisation name]…………………… NOTE: (not for inclusion in the Exposition) 1. Whenever the Accountable Manager is changed it is important that the new Accountable Manager reviews and signs the statement at the earliest opportunity as part of his/her acceptance by DGTA-ADF. Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 8 of 52 1.2 SAFETY AND QUALITY POLICY (DASR 145.A.30(a)2,65(a), 70(a)2) The Safety and Quality Policy should, as a minimum, include a statement committing the organisation to: recognise safety as a prime consideration at all times; apply Human Factors principles; encourage personnel to report maintenance related errors/incidents to meet DASR 145 requirements; recognise that compliance with procedures, quality standards and regulations is the duty of all personnel; and recognise the need for all personnel to cooperate with the Quality Auditors. Sample Safety Policy Statement Refer to GM 145.A.65(a) Safety is the first priority in all our activities. We are committed to implementing, developing and improving strategies, management systems and processes to ensure that all our aviation activities uphold the highest level of safety performance and meet national and international standards. In order to achieve this, our safety objectives are set down in this policy statement. Our commitment is to: 1 Develop and embed a safety culture in all our aviation activities that recognises the importance and value of effective aviation safety management and acknowledges at all times that safety is paramount. 2 Clearly define for all employees their accountabilities and responsibilities for the development and delivery of aviation safety strategy and performance. 3 Minimise the risks associated with aircraft operations so far as is reasonably practicable. 4 Ensure that externally supplied systems and services that impact upon the safety of our operations, meet appropriate safety standards. 5 Actively develop and improve our safety processes to conform to world-class standards. 6 Comply with and, wherever possible, exceed regulatory requirements and standards, including but not necessarily limited to those mandated by Defence. 7 Ensure that all employees are provided with adequate and appropriate aviation safety information and training, are competent in safety matters and are only allocated tasks commensurate with their skills. 8 Ensure that sufficient skilled and trained resources are provided and available to manage safety and implement safety strategy and policy. 9 Establish and measure our safety performance against realistic objectives and/or targets. 10 Achieve the highest levels of safety standards and performance in all our aviation activities. 11 Continually improve our safety performance levels. 12 Conduct safety and management reviews and ensure that relevant action is taken 13 Actively encourage, promote, reward and give feedback in response to safety reporting amongst our staff; and. 14 Ensure that aviation safety is maximised through the application of an effective SMS, which is integral to all our aviation activities Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 9 of 52 1.3 MANAGEMENT PERSONNEL (DASR 145.A.30(a), (b), (c), 65(e), 70(a)3) This section should identify the maintenance management personnel of the organisation by listing, at least, the title and name of the Accountable Manager plus all the persons nominated to hold a position as required by DASR 145.A30(b) and (c). Where known their respective deputies should also be identified.(not for inclusion in the Exposition) Accountable Manager...................................................................... Deputy Accountable Manager.......…(If applicable).......................... Responsible Manager Flight Line Maintenance ……(If applicable)….. Deputy Responsible Manager Flight Line Maintenance.(If applicable). Responsible Manager Aircraft Maintenance………(If applicable)…… Deputy Responsible Manager Aircraft Maintenance…(If applicable)… Responsible Manager Workshop maintenance .......(If applicable)...... Quality Manager ............................................................................... Deputy Quality Manager .....................(If applicable)…..................... Safety Manager ………………….............................…....................... Deputy Safety Manager …………......(If applicable)…....................... NOTES: (not for inclusion in the Exposition) 1. This list comprises the minimum Senior Personnel in a medium to large organisation that DGTA-ADF would require a DASR Form 4 to be completed. Lesser posts could exist in a smaller organisation. This, in effect, is the "group of persons" referred to in DASR 145.A.30(b) whose responsibilities include ensuring that the DASR 145 AMO remains in compliance with DASR 145 requirements. These persons are ultimately directly responsible to the Accountable Manager for this function. 2. Other posts may be added if desired but it should be clearly shown whether or not they are considered as "management" for DASR Form 4 purposes. A marked separation (dividing line) would suffice with the text "no DASR Form 4 required" or, identify each post in this way 3. It is recommended that this list is included in the Exposition on a separate page so that it can be easily amended when changes occur 4. Whilst not mandatory, consider including a procedure to show, when and who can deputise for any responsible persons under DASR 145.A.30(b) in the case of a lengthy absence of that responsible person. Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 10 of 52 1.4 DUTIES AND RESPONSIBILITIES OF MANAGEMENT PERSONNEL (DASR 145.A.30, 70(a) 4) This section should list the responsibilities of the individuals occupying the following positions. 1.4.1 Accountable Manager (DASR 145.A.30(a), 145.A.70(a)1, 4) This section details the duties and responsibilities of the Accountable Manager in relation to the AMO, and demonstrates that the Accountable Manager has corporate authority for ensuring that all maintenance services can be financed and carried out to the required standard. As a minimum these should include: a. ensuring that maintenance carried out by the approved organisation meets the standards required by DGTA-ADF b. establishing and promoting the safety and quality policy specified in DASR 145.A.65(a). c. nominating the management staff. d. ensuring that the necessary finance, manpower resources and facilities are available to enable the company to perform the maintenance to which it is committed for contracted CAMOs, and any additional work which may be undertaken. e. nominating the senior person for monitoring of the quality system. f. ensuring the competence of all personnel including management personnel has been assessed and satisfy DASR 145 requirements. 1.4.2 Responsible Manager (DASR 145.A.30(b), 145.A.70(a)3, 4) This section should identify and set out the duties and responsibilities of each responsible manager the level of detail should be sufficient to show that all the responsibilities and obligations of the AMO under DASR 145 are covered by the responsible managers. As a minimum these should include: a. the satisfactory completion and certification of all work required by contracted CAMOs, in accordance with the work specification. b. ensuring that the organisation's procedures and standards are complied with when carrying out maintenance c. ensuring, through the workforce under his/her control, that the quality of workmanship in the final product is to a standard acceptable to the organisation and DGTA-ADF. d. ensuring the competence of all personnel engaged in maintenance by establishing a programme of training and continuation training using Internal and external sources; On-the-job instruction and evaluation, and Examination/testing as necessary. e. keeping a record of all training and experience of maintenance-related personnel. f. ensuring that all sub-contract orders are correctly detailed and that the requirements of the contract/order are fulfilled in respect of inspection and quality control. Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 11 of 52 g. responding to quality deficiencies in the area of activity for which he/she is responsible, which arise from independent quality audits. If there is more than one responsible manager then their responsibilities and obligations shall be framed to ensure no overlapping of responsibilities, with reference to the appropriate regulation. The size of the AMO and the complexity of its scope of approval and the capability of individuals nominated will determine the number of Responsible Managers required. NOTES: (not for inclusion in the Exposition) 1. Additional duties and responsibilities may be added provided they do not conflict with those of other management personnel 2. The combined Duties and Responsibilities of managers should illustrate the composition of the Quality System in the particular organisation by making it clear how quality standards are set and quality is controlled 1.4.3 Quality Manager (DASR 145.A.30(c), 65(a), (c), 70(a)4) This section should identify and set out the duties and responsibilities of the quality manager, and shall demonstrate that he/she reports directly to the accountable manager for all quality related matters. The Quality Manager is responsible for establishing an independent quality system to monitor compliance with DASR 145.A requirements. He/she is responsible for implementing a quality audit programme in which conformance with all maintenance procedures is reviewed at regular intervals, in relation to each type of aircraft (or component) maintained, and any observed noncompliances or poor standards are brought to the attention of the person concerned via his/her manager. With specific reference to the DASR 145 approval, the Quality Manager is responsible for: assessing sub-contractors for extension of the quality system, and maintaining the expertise necessary to be able to do so, to the satisfaction of DGTA-ADF assessing external specialist services required to be used by the company in the performance of maintenance assessing suppliers of new and used components, and materials, for satisfactory product quality in relation to the needs of the organisation preparing standard practices and procedures for use within the organisation, derived from approved sources, and keeping them up to date NOTE: (not for inclusion in the Exposition) 1. The functions defined above are typical for a medium to small sized organisation. The actual division of duties will vary with the particular organisation so that some tasks may be accomplished by, for example, Planning, Production or Technical Services etc 2. The quality system is required to be "independent" which will normally mean that the Quality Manager and the Quality Monitoring Staff are not directly involved in the maintenance process or with maintenance certification Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 12 of 52 1.4.4 Safety Manager (DASR 145.A.65(a), (e)) This section should identify and set out the duties and responsibilities of the Safety Manager, and should demonstrate that he/she reports directly to the accountable manager for all safety related matters. 1.4.5 Other Relevant Personnel (DASR 145.A.30(f)) NOTES: (not for inclusion in the Exposition) 1. This section can be continued with the terms of reference of additional management personnel, who report to the upper level of management, as necessary to fully describe the organisation. 2. These personnel would not normally be required to complete a DASR Form 4. (to be agreed with the relevant DGTA-ADF section representative. 3. This section should include the nominated level 3 for NDT who does require nomination on a DASR Form 4. AMC 145.A.30 states “Form 4 not required when a member of the NMAA”. Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 13 of 52 1.5 MANAGEMENT ORGANISATION CHART (DASR 145.A.70(a)5) This section sets out the organisational chart depicting reporting lines and chains of responsibility of managers. Independence of Quality and Safety Managers from the maintenance organisation structure as required by DASR 145.A.30(c) should be shown. The following charts show examples of acceptable organisational structures for DASR 145 AMO. DASR Form 4 post holders must be clearly identified in the chart. Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 14 of 52 1.6 CERTIFYING STAFF (DASR 145.A.30 (g), (h), 70(a)6) This section should contain a list of all certifying staff authorised within the AMO. This paragraph may be cross referenced from another record (including a computer record) where the list of the names is kept. If the organisation's individual staff authorisation records are referred to as the "list", they should be preceded by a summary listing all of the staff names included, thereby meeting the intent of DASR requirement The intention of this paragraph is that the AMO maintain a complete up-to-date record of all certifying staff and that it be provided to DGTA-ADF with the MOE when requesting initial or amended approval or on request by DGTA-ADF staff. AMOs Intending to use the Defence Technical Equivalent Qualification (DTEQ) as the National Equivalent qualification in accordance with DASR 145.A.30(g-j) should provide a list of all authorised maintenance personnel here. Where this list is cross referenced from a separate record the source of the record should be identified/referenced herein. The list should include all personnel authorised for any of the following roles: Trades persons Self Certifying Technicians Trades Supervisors Independent Inspectors Maintenance Managers AMOs intending to use DASR 66 or equivalent NMAA approved qualifications for their certifying personnel should list all of their certifying personnel as detailed in the following paragraphs. 1.6.1 CAT C Certifying Staff 1.6.2 Base Certifying Staff Line Certifying Staff (Mechanical/Avionic) Cat B1 Technicians Cat B2 Technicians Cat A Mechanics 1.6.3 Component Certifying Staff (DASR Form 1) 1.6.4 Base Maintenance (Category B1 And B2 Qualified Support) Staff Cat B1 Technicians Cat B2 Technicians Where this list is cross referenced from a separate record the source of the record should be identified/referenced herein. The list should include at least the following information: Name DASR certification category Identification of the support staff category Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 15 of 52 Function Authorisation Identification number Date of first issue of the authorisation Expiry date of the authorisation Scope/ limitation of the authorisation For aircraft certifying staff and support staff only, their aircraft maintenance licence number. List the standards of personnel qualifications that the AMO will recognise and require for each type of certifying employee to be authorised by the organisation as described under section 145.A.30. Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 16 of 52 1.7 MANPOWER RESOURCES (DASR 145.A.30(d), 70(a)7) This section should demonstrate how the organisation ensures the AMO has sufficient employees to plan, perform, supervise, inspect and certify for maintenance and audit the AMO for compliance and safety in accordance with the Quality and Safety Management Systems required by DASR 145.A.65(c) and (e) for each maintenance function and location. The AMO’s policies relating to the number of employees required under various types of maintenance and the levels of supervision required between individual maintainers and Certification Authorisation holders should be shown here consistent with the maintenance management system. 1.7.1 Base Maintenance / Component Maintenance Maintenance - Aircraft / Workshops Engineering Technical Services Planning Administration Quality Dept. Quality Audit etc 1.7.2 Line Maintenance Maintenance Engineering Technical Services 1.7.3 Specialised Activities Technical Services 1.7.4 Sub-Contracted Services Full Time Part Time NOTES: (not for inclusion in the Exposition) 1 The resources described must justify the grant of approval as defined in paragraphs 1.8 (facilities to be approved) and 1.9 (scope of work) in sufficient detail to explain the support at each site and for each function as required by 145.A.30(d). 2. Numbers of personnel should be given in general terms so that a clear picture is given without the need for amendment as a result of routine staff fluctuations, but able to highlight any significant re-deployment or loss of staff. 3. Where the approval is sub-divided into sites or different major functions the resources should be related to each site and function. Resources do not only mean numbers, it also means qualifications and competence. Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 17 of 52 1.8 FACILITIES (DASR 145.A.25, 70(a)8, 15) This section should describe, in some detail, each of the facilities at which the organisation intends to carry out maintenance, thereby building up a picture of what the DGTA-ADF is being asked to approve. All main locations should be included; however a different emphasis can be placed on locations of different importance. For example, the main locations, which are listed in the approval document, will need a detailed description. Other significant locations such as frequently used detachment/deployment locations should be clearly described while transit locations occasionally used for minor line maintenance tasks may be briefly covered. 1.8.1 Base Maintenance This section should demonstrate specific requirements for Base Maintenance facilities in accordance with the DASR 145.A.25. These include: hangar accommodation; specialist workshops; environmental provisions; office accommodation; and storage and supply of aircraft components, materials, tools and equipment. 1.8.2 Line Maintenance This section should describe facilities utilised at each main location, to provide evidence that the facilities are appropriate for the maintenance services to be provided at that location and are appropriate for the scope of Line Maintenance as approved for the organisation. Note: Refer to 1.8.4 below for temporary maintenance locations 1.8.3 Component Maintenance This section should describe facilities in adequate detail to show that: workshops are large enough to accommodate the product to be maintained; serviceable and unserviceable components, equipment and tools are segregated; facilities for the accommodation of tools and equipment comply with manufacturers instructions; and provide for adequate security of storage facilities. 1.8.4 Locations other than those listed in the Exposition (DASR145.A.75(c)) This section will contain procedures for assessment of existing facilities, tooling, equipment, data and personnel at locations where the AMO is required to carry out unscheduled and unforeseen maintenance. Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 18 of 52 1.9 SCOPE OF WORK (DASR 145.A.20, 42(c), 70(a)9, 75, 80) An AMOs approved scope of maintenance will be defined by the Approval Certificate and exposition approved by DGTA-ADF. The Approval Certificate may list the main locations, Classes, Ratings and their limitations for the Maintenance Services that the AMO is approved to provide. This paragraph must show the range of work carried out at each approved site within the scope of each approval rating shown in the "Schedule of Approval". This section should also relate to paragraph 1.8 in such a way that it can be clearly seen what tasks are performed at which locations. 1.9.1 Aircraft Maintenance Location Class Rating Amberley Aircraft A1 Williamtown 1.9.2 A1 Base Yes Yes Line Yes Yes No Yes No No No Yes Yes Yes Engine Maintenance Location Sydney 1.9.3 Aircraft Limitation B737-200 A330200/CFM56 A320200/V2500 B737-200 B737-200 A320200/V2500 Class Engine Rating B1 Limitation CFM 56-7B (Overhaul) Component Maintenance Location Class Rating Sydney Component C3 Melbourne Component C3 S1000D Chapter Limitation Reference 23 – 34 Raytheon Sikorsky 23 – 34 Raytheon Sikorsky Rockwell Collins 1.9.4 Specialist Maintenance (DASR 145.A.30(f)) If the AMO carries out Specialist Maintenance as part of the provision of maintenance it provides under an A, B or C rating, and does not hold a D rating for the Specialist Maintenance, this section of the exposition will fully describe the procedures, facilities, equipment and tooling, data used and employee qualifications used for that Specialist Maintenance. If the AMO has a D rating for the Specialist Maintenance that it carries out, this section of the exposition may be set out in tabular form as laid out above for maintenance within the scope of the AMOs approval certificate at various locations. 1.9.5 Additional Significant Activities This should include any NDT activities or special processes such as welding, electroplating, surface finishing, structural repairs and life support maintenance that are carried out internally and not necessarily included on Approval Certificate. Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 19 of 52 1.9.6 Fabrication in the Course of Maintenance (DASR 145.A.42(c)) If an AMO has been approved to maintain aircraft or aircraft components under DASR 145, it may only fabricate a part for an aircraft or component covered by its certificate of approval, and only if it has the capability to fabricate the particular part with respect to appropriate facilities, tools and trained and competent employees. If the AMO fabricates parts in the course of maintenance, this section of the exposition will specify procedures to be used to ensure all requirements of DASR 145.A.42(c) are complied with. 1.10 CHANGES TO THE ORGANISATION (DASR 145.A.70(b), 70(a)10) 1.10.1 Significant Changes (DASR 145.A.85) This section should set out the procedure that the AMO must follow for making changes to the organisation. In particular, it should set out how the changes are initiated and assessed, how applications are made, how the organisation ensures that the change is fully incorporated and who within the organisation is responsible for managing these changes. NOTES: (not for inclusion in the Exposition) 1 DGTA-ADF approval is based on the management, organisation, resources, facilities and scope of work described in this Part 1 of the Exposition. Any significant change therefore affects the conditions under which the approval was granted and has been allowed to continue. This part of the Exposition must show how the AMO would go about notifying DGTA-ADF of the following changes: 2 Changes to the Accountable Manager or Senior nominated management personnel – along with a completed DASR Form 4 and supporting Exposition amendment proposal in time to allow DGTA-ADF to "accept" the nominated person (see DASR Form 4) and approve the proposed Exposition amendment prior to the commencement of their appointment. 3. Changes affecting the Schedule of Approval (DASR Form 3) -- By application to DGTA-ADF using the DASR Form 2 4. Changes affecting the approved facilities (addresses) and Scope of Work -- By notification to DGTA-ADF, enclosing the draft Exposition change. 1.10.2 Minor Changes (DASR 145.A.70(c)) Minor Changes to the organisation and its exposition may be approved by the AMO in accordance with DASR 145.A.70(c) without prior approval by DGTA-ADF. This section should set out the procedure that the AMO must follow for making changes to the organisation that are considered minor changes. In particular, it should set out how the changes are initiated and assessed, how applications are made, how approvals are given, how the organisation ensures that the change is fully incorporated, how the organisation notifies DGTA-ADF and who within the organisation is responsible Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 20 of 52 1.11 EXPOSITION AMENDMENT PROCEDURES (DASR 145.A.70(a)11, 70(b), (c)) 1.11.1 Exposition Management This section should identify how the AMO ensures that the exposition and associated procedures and manuals is kept up to date and it complies with DASR 145.A.70 in relation to its content and who is responsible for this. 1.11.2 Changes to AMO Exposition This section should set out the how any proposed changes to the exposition are initiated, who is responsible for assessing the proposed change to determine whether the change needs to be approved by DGTA-ADF, or whether it may be approved inhouse. The section should set out the procedures for making applications for changes to DGTA-ADF or if applicable, the procedures for in-house approval by the AMO. It should also identify the individual who is responsible for incorporating the change in the exposition once it is approved. This part of the document should clearly show how the Exposition is "managed" and the distinction between those parts under the control of the company and those parts for which amendments are required to receive prior DGTA-ADF approval. Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 21 of 52 PART 2 MAINTENANCE PROCEDURES This part should set out, in detail, how the AMO provides the maintenance services it is approved and required to provide in order to ensure that it meets its obligation under DASR145. It is acceptable to refer to other documents and manuals of the AMO in order to prevent the exposition from becoming unmanageably large. However, if this is done, then the other documents and manuals become subject to the same requirements and controls as the exposition e.g. DGTA-ADF approval and change management. In this specimen Exposition the paragraph titles of AMC 145.A.70(a)6 are utilised to provide an acceptable path to compliance with the DASR 145 requirements. In each case subject headings are suggested in which the particular nature of the organisation's actual procedures could be defined. Subject headings should be deleted if they do not apply and others may be included if that is the most suitable method of describing the particular organisation. 2.1 SUPPLIER EVALUATION AND SUBCONTRACT CONTROL PROCEDURE (DASR 145.A. 65(c), 70(a)14, 75(b)) Suggested subject headings Company Policy — (sources of supplies) Records of utilisation List of Approved Suppliers Monitoring of Suppliers Quality systems Findings, corrective and preventative actions System for placing orders Pre Contract Audit procedures Control of Subcontractors Documentation to be used 2.2 ACCEPTANCE / INSPECTION OF AIRCRAFT COMPONENTS AND MATERIALS FROM OUTSIDE CONTRACTORS ((DASR 145.A.42, 43, 50(f)) Suggested subject headings Component/Standard Part/Material acceptance procedures — (sources, conformity, eligibility acceptability to company requirements, records) Incoming inspection — (required documentation, compliance with order, condition, "Quarantine" procedure) Acceptance of components from internal sources Components removed serviceable from aircraft Control of components received from customers for Repair and/or Overhaul etc. Acceptance of components with other than approved release certificates IAW DASR 145.A.50(f) Procedures for dealing with suspected unapproved parts. Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 22 of 52 2.3 STORAGE, TAGGING AND RELEASE OF COMPONENTS AND MATERIALS (DASR 145.A.25(d),42, 43, 50(d)) Suggested subject headings Procedures for maintaining satisfactory storage conditions — (rotables, perishables, flammable fluids, engines, bulky assemblies and special storage requirements) System for control of shelf life and modification standard Tagging/Labelling system (serviceable, unserviceable, robbery, scrap etc.) Segregation of Serviceable/Unserviceable parts Procedures for dealing with Unsalvageable components, suspected unapproved parts and quarantine.) Issue of components and materials to maintenance The storage condition and the storage limitation must be based upon security requirements and manufacturer specifications. 2.4 ACCEPTANCE OF TOOLS AND EQUIPMENT (DASR 145.A.40(a) Suggested subject headings Procedure for receiving tools and equipment Method for tracking service life Method of labelling tooling serviceable or otherwise Method of storing the paperwork specific to each item including manufacturers instructions and calibration reports Process for acceptance — (identification, certification, control, calibration) Procedure for the control of Alternate tools Procedure for identification and approval of Instructions for Continuing Airworthiness (ICA) / Maintenance data for the use of alternative tools and equipment. Aircraft access equipment and inspection platforms/docking 2.5 CALIBRATION OF TOOLS AND EQUIPMENT (DASR145.A.40(b)) Suggested subject headings Inspection, servicing and calibration programme/equipment register Establishment of inspection, servicing and calibration time periods and frequencies Identification of servicing/calibration due dates List of Standards being used Calibration procedures for serviceability and accuracy Recording and storage of the calibrated item and the standard it was calibrated against Procedure for quarantine and investigation of tools and components or aircraft affected by the discovery of out of tolerance tooling 2.6 USE OF TOOLING AND EQUIPMENT BY STAFF (DASR 145.A.40(a), 48(d), (j)) Suggested subject headings Issue of tools — (record of user and location) Determining tool serviceability prior to issue Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 23 of 52 Training and certification of employees in the use of tools and equipment Personal (own) instrument/tool control Loan tool control and audit Alternative tool identification, data approval and use as per DASR 145.A.40(a)1 and 45(d) 2.7 CLEANLINESS STANDARDS OF MAINTENANCE FACILITIES (DASR 145.A.25(a), 48(b), (j), AMC 145.A48(j) AMC2) Suggested subject headings "Foreign Object" exclusion programme IAW AMC 145.A48(j) AMC2 Cleaning programme — individual responsibilities — Timescales Waste material disposal Segregation of working spaces Dust suppression in the workspace 2.8 MAINTENANCE INSTRUCTIONS AND RELATIONSHIP TO AIRCRAFT/ AIRCRAFT COMPONENT MANUFACTURERS’ INSTRUCTION INCLUDING UPDATING AND AVAILABILITY TO STAFF (DASR 145.A.45, 48(c)) Suggested subject headings Control of information — Technical library (information held, control, issue) Technical information amendment procedures — Manuals — Service Information — Uncontrolled copies of manuals Company Technical Procedures / Instructions Awareness of Technical Publications, Instructions and Service Information Maintenance documentation — (preparation from approved sources — amendment control) DGTA-ADF acceptance of organisation's transfer of ICA/Maintenance Data Review and identification of amendment status of ICA/Maintenance Data Distribution of ICA/Maintenance Data — access by maintenance personnel The verification and validation of new procedures where practicable Incorporation of best practice and human factors principles Control of customer supplied ICA/Maintenance Data Control of CAMO supplied ICA/Maintenance Data Modification of Maintenance Data 2.9 REPAIR PROCEDURES (DASR 145.A.42(f), 45, 48(c), (i)) Suggested subject headings Company policy — (internal/external — sources of repair approval) Company approvals — scope of work — limitations and conditions Control system for fabrication of parts in the course of maintenance, processing and inspection in accordance with 145.A.42(c) Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 24 of 52 2.10 AIRCRAFT MAINTENANCE PROGRAMME COMPLIANCE (DASR 145.A.45, 47,70) Suggested subject headings Maintenance programme variations if applicable Control of programme and amendments Reliability monitoring and reporting Corrosion control programme reporting Maintenance Programme Inspection Standards 2.11 AIRWORTHINESS DIRECTIVES PROCEDURE (DASR 145.A.45) Suggested subject headings Airworthiness Directive (AD) response procedure — (terminating action/ inspection) Records of AD compliance and certification Repetitive AD requirements — (inspection control) 2.12 OPTIONAL MODIFICATION PROCEDURE (DASR 145.A.45, 42(c), 47) Suggested subject headings Continued Airworthiness information — (assessment procedure and methods of response) Modification control — (requirements and approval) 2.13 MAINTENANCE DOCUMENTATION (DASR 145.A.45(e), (f), 50(a), (b), 55) Suggested subject headings Worksheets for non-routine tasks Assembly of work packages for issue to maintenance activity Work sheet/card completion — Maintenance sign-off and the performance of Maintenance Certification Assembly of completed work package for coordination and CRS issue Recording of test results and dimensions Control and use of customer/CAMO supplied work card/sheets 2.14 TECHNICAL RECORDS CONTROL (DASR 145.A.45(e), 55) Suggested subject headings System for control, storage and retrieval (paper or computer based) Control of access to records — (paper and/or computer based records) Record-keeping systems — (essential records) Turbine engines — module records Disposal of records — transfer of aircraft Lost or destroyed records (reconstruction and DGTA-ADF acceptance) Provision of maintenance records (CRS) to the CAMO Retention of records (periods — methods and security) Control of access to records of aircraft involved in accidents/incidents Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 25 of 52 2.15 RECTIFICATION OF DEFECTS ARISING DURING BASE MAINTENANCE (DASR 145.A.50(c & e), 55) New defects or incomplete maintenance work orders identified during maintenance shall be brought to the attention of the customer Operating Organisation for the specific purpose of obtaining agreement to rectify such defects or completing the missing elements of the maintenance work order. In the case where the customer declines to have such maintenance carried out, 145.A.50(e) is applicable in order to issue the release to service (with deferred maintenance), as addressed in MOE chapter 2.16 Suggested subject headings Recording and sign-off of base maintenance defects Carrying forward defects to future maintenance Inputs — (control and accountability) Analysis of defects and rectification — human factors — maintenance programme implications — reliability Notification process (when necessary) 2.16 CERTIFICATION OF MAINTENANCE AND CERTIFICATE OF RELEASE TO SERVICE PROCEDURES (DASR145.A.30(g-j),45(e), 50) Suggested subject headings Company procedures — (CRS statement) Issue of CRS after Base Maintenance Issue of CRS after Line Maintenance Issue of a CRS with incomplete work Issue of a certification authorisation after defect rectification – Base/Line Sign-off after maintenance task completion (DASR AMC 145.A.65(b)(3)) Issue of DASR Form 1 Certification — identity — qualified employees Cross-reference to work packs Re-release of components removed serviceable from aircraft (DASR AMC 145.A42(g)4 and AMC50(d)AMC1) 2.17 RECORDS FOR THE CAMO (DASR 145.A.55(a), (b)) Suggested subject headings Contractor record keeping — specific CAMOs Arrangements for processing and retention of maintenance records 2.18 OCCURRENCE REPORTING TO DGTA-ADF/CAMO/MTCH/STC HOLDER (DASR 145.A.50(a), 60, 70(a)12) Suggested subject headings Methods of Reporting to: º DGTA-ADF º Manufacturer º CAMO Persons Responsible for Reporting Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 26 of 52 Reports must contain pertinent and evaluation results (where known) Defects Reported by Subcontractors and lessees Permitted Reporting Periods and Retention of Data Reportable Defects Investigation procedure and follow-up system Reporting timescale Process for follow-up of report for action Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 27 of 52 2.19 RETURN OF DEFECTIVE AIRCRAFT COMPONENTS TO STORE (DASR 145.A.43) Suggested subject headings Labelling and identification — (required information) Handling and movement of aircraft components Storage and segregation of defective aircraft components Aircraft components "on hold" (pending determination of serviceability status) 2.20 DEFECTIVE AIRCRAFT COMPONENTS TO OUTSIDE CONTRACTORS (DASR 145.A.43) Suggested subject headings Dispatch of aircraft components for repair/overhaul/calibration Control of dispatch, location and return Identification of required work Return of unserviceable components Reporting requirements. 2.21 CONTROL OF COMPUTER MAINTENANCE RECORDS SYSTEM (DASR 145.A.45(e), 55(c), AMC50(b)5) Suggested subject headings Information retrieval Back-up systems and second site storage Security and safeguards to unauthorised access 2.22 MAN-HOURS PLANNING (DASR145.A.30(d) and 145.A.47) Suggested subject headings Company planning v time available procedure Actions where deviation from man-hour plan exceeds 25% Complexity of work Organisation of shifts Account of human performance limitations 2.23 CONTROL OF CRITICAL TASKS (DASR 145.A.65(b), 48(g), (h)) Suggested subject headings Independent verification — inspection procedures Critical task procedures and control Critical task list EROPs 2.24 SPECIFIC PROCEDURES (DASR 145.A.48, 65(b)) Suggested subject headings Engine running Aircraft post maintenance check flights Aircraft pressure run Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 28 of 52 Aircraft towing Aircraft marshalling Aircraft Weighing Aircraft wash Scrapping of unsalvageable parts Working away from main base/workshop Handling and control of hazardous and waste materials GSE maintenance procedures Aircraft de-icing 2.25 PROCEDURES TO DETECT AND RECTIFY MAINTENANCE ERRORS (DASR145.A.48(g), (h), 60, 65(b)) Suggested subject headings Aims and objectives of error management system The encouragement of reporting A code of practice Description of process that reports occurrences Description of process that investigates occurrences Description of process that records occurrences The analysis of occurrence data Management actions in response to occurrence findings Feedback to employees Sharing information from investigations Just culture Link to safety management system 2.26 SHIFT/TASK HANDOVER PROCEDURES (DASR145.A.47(c), 65(b)) Suggested subject headings: Aims and objectives of the shift handover Training of personnel in shift/task handover processes Recording of shift/task handover Description of shift handover process º Facility status º Work status º Manning status º Outstanding issues º Other Information 2.27 PROCEDURES FOR NOTIFICATION OF MAINTENANCE DATA INACCURACIES, INCOMPLETENESS AND AMBIGUITIES TO DGTA-ADF/CAMO/MTCH/STC HOLDER (DASR 145.A.45(c), 65(b)) Suggested subject headings: Definitions of ICA / maintenance data ambiguities Responsible person for coordination of reporting and remedial actions Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 29 of 52 2.28 Method of internal reporting of ICA / maintenance data ambiguities Method of external reporting of ICA / maintenance data ambiguities to the appropriate CAMO and authors of that data Procedures for alteration and generation of ICA/ maintenance data paragraphs 145.A.45(b) Feedback to employees and implementation of TC Holder/Manufacturers corrections PRODUCTION PLANNING PROCEDURES (DASR145.A.47) Suggested subject headings: Establishment of a clear work order or contract Procedures for establishing all necessary resources are available before commencement of work Procedures for organising maintenance personnel and providing all necessary support during maintenance Consideration of human performance limitations Planning of critical tasks Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 30 of 52 PART L2 ADDITIONAL LINE MAINTENANCE PROCEDURES (DASR 145.A.65(b)) NOTE:(not for inclusion in the Exposition) This part need not be included in the Exposition if the organisation's Schedule of Approval does not include the performance of Line Maintenance in Ratings "A1", "A2" or "A3". MOE Part L2 is intended to provide additional procedures which are specific for the line maintenance environment, which have been not been covered in the MOE Part 2. Where a procedure, was already covered in the MOE part 2 and there is no need of further detail to be added, a direct reference to the MOE (part 2) chapter may be used in the relevant MOE (part L2) chapter. L2.1 LINE MAINTENANCE CONTROL OF AIRCRAFT COMPONENTS, TOOLS, EQUIPMENT, ETC. (DASR 145.A.40, 42, 43, 45, 48(j), 50(d), 75) Suggested subject heading Components/Material acceptance — required, documentation, condition, "Quarantine" procedure Components removed serviceable from aircraft (DASR 145.A.20 Appendix II 4 and 5, AMC 145.A.42(g)) Procedures for maintaining satisfactory storage conditions — (perishables, flammable fluids, engines, bulky assemblies, special storage requirements) System for control of shelf life and modification standard Tagging/labelling system (serviceable; serviceable removed from aircraft; unserviceable; scrap; suspected unapproved parts; quarantine etc.) Issue of components and materials to the maintenance process Free-issue dispensing of standard parts (control, identification, segregation) Tools and Test Equipment, servicing and calibration program / equipment register / tool control after maintenance with regards to DASR 145.48(d)) Identification of servicing/calibration due dates L2.2 LINE MAINTENANCE PROCEDURES RELATED TO SERVICING / FUELLING / DE-ICING ETC. (DASR 145.A.40, 42, 45, 48) Suggested subject headings Maintenance documentation —(control and amendment) Airworthiness data — (control and amendment) Fuel supply quality monitoring: º bulk storage º aircraft re-fuelling Ground de-icing: º Procedures (including inspection for/ removal of de-icing/anti-icing fluid residues, etc.) º Monitoring of sub-contractors Maintenance carried out in the open — (limitations, Human Factors/maintenance error management) Maintenance of ground support equipment Monitoring of contracted ground handling and servicing Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 31 of 52 Care and maintenance of cargo loading systems / retention equipment L2.3 LINE MAINTENANCE CONTROL OF DEFECTS AND REPETITIVE DEFECTS (DASR 145.A.50) Suggested subject headings Reportable defects — Engineering entries — Cabin Deferred defect classification system Rules for deferring (periods — review — permitted personnel — conformity with MEL/CDL provisions) Certification of defect rectification —- Transfer of defects to worksheets / cards Awareness of deferred defects carried by aircraft — monitoring of repetitive defects Communication with main base L2.4 LINE PROCEDURE FOR COMPLETION OF TECHNICAL LOG (DASR 145.A.50(a), (b), (e), (f), 55(a), (b), 65(b)) Suggested subject headings Explanation of Technical Log system — completion of Sector Record Page — Distribution of copies Certification/Sign-off — Maintenance, Pre-flight/Transit, EDTO — Independent Inspections Maintenance control systems — Special Inspections, Out-of-Phase maintenance Retention of records - Control Maintenance Statements L2.5 LINE PROCEDURE FOR POOLED PARTS AND LOAN PARTS (DASR 145.A.42, 43, 50(f), 65(b)) Suggested subject headings Verification of approved sources of parts — Modification Standard and AD compliance Compliance with loan and contract requirements — Tracking and control Required documentation Processing removed loan parts for return to source — service record Cannibalisation system — control procedures, authority Use parts released by an alternate/unrecognised release certificate iaw DASR 145.A.50(f) derogation L2.6 LINE PROCEDURE FOR RETURN OF DEFECTIVE PARTS (DASR 145.A.42, 43) Suggested subject headings Required documentation — service record Processing advice of removal and dispatch to Technical Records Dispatch to rectification L2.7 LINE PROCEDURE FOR CONTROL OF CRITICAL TASKS (DASR 145.A.48,(g), (h), 65(b)) Suggested subject headings Allocation of employees Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 32 of 52 Assignment of secondary inspections Establish procedures as required by DASR AMC 145.A.65(b)3 Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 33 of 52 PART 3 QUALITY AND SAFETY MANAGEMENT PROCEDURES 3.1 QUALITY MANAGEMENT SYSTEMS (DASR 145.A.30(c), 65(a) - (d), 70(a)12) Suggested subject heading Audit procedures for regulatory compliance and maintenance standards Systems for remedial corrective and preventative action and feedback Identification, legibility, storage, protection, archiving, retrieval and retention of records Regular review of Quality Management System procedures Staff access to QMS 3.2 QUALITY AUDIT OF ORGANISATION PROCEDURES (DASR 145.A.65(c), 70(a)12) Suggested subject headings Company Audit Policy/Plan/Schedule (DASR 145.A.65(c)1) Definition of the Quality System Independence access to Accountable Manager Composition and functions of quality management group paragraph 145.A.35(i) of the DASR 145 Annual Review of Maintenance Procedures (Sample) Audit programme — Adequate and satisfactory facilities Compliance with approved procedures Dates and timescales Audit of suppliers and Subcontractors 3.3 QUALITY AUDIT OF AIRCRAFT AND COMPONENTS (DASR145.A.65(c)1) Suggested subject headings Scope of Maintenance System description Audit programme Auditing of standards Product samples (aircraft and/or components) Dates and timescales Auditing methods Sampling. Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 34 of 52 3.4 QUALITY AUDIT REMEDIAL ACTION PROCEDURE (DASR 145.A.30(a), (c), 65(c)2) Suggested subject headings Quality audit finding and risk assessments Quality audit report feedback system Accountable Manager/senior management review meeting Corrective action and timescale including remedial and disciplinary action and/or penalties. Management responsibilities for corrective action and follow-up Quality audit and feedback records 3.5 CERTIFYING STAFF – QUALIFICATIONS AND TRAINING (DASR 145.A.30(c), (e), (g), (j), 35(a) to (g), (m)) Suggested subject headings Experience, training and competence requirements Examination, test or assess procedure Continuation training program Continuation training procedures Qualifying subcontractor's personnel (if applicable) Authorisations issue and renewal procedures iaw DASR145.A.35(a), (b), (c) and (f) º currency º licence validity º age requirements iaw DASR 145.A.35(m) One off certification authorisation iaw DASR 145.A.30(j)5. Any Flight Crew limited certification authorisation iaw DASR 145.A.30(j)3. 3.6 CERTIFYING STAFF RECORDS (DASR145.A.35(j) to (l), 70(a)6) Suggested subject headings List of certifying personnel and B1/B2 support staff, Minimum information list of employee particulars Control of certifying employee records paragraphs iaw DASR 145.A.35(j) and (l) Access to employee records iaw DASR 145.A.35(g), (j), (k) and (l) for authorised persons, authorised managers and DGTA-ADF personnel Retention of records iaw DASR 145.A.35(j) Format of authorisation document and authorisation codes 3.7 QUALIFICATION OF QUALITY AUDIT PERSONNEL (DASR 145.A.30(e), 65(d)) Suggested subject headings Nominated personnel Experience (duration and technical), training and competence requirements Independence of quality audit personnel Assessment procedures (Examination and Testing) Continuation training (Programme and Procedures) Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 35 of 52 3.8 QUALIFICATION OF MAINTENANCE SUPERVISORS (DASR 145.A.30(e), 65(d)) Suggested subject headings Experience (duration and technical), training and competence requirements Assessment procedures (Examination and Testing) Continuation training (Programme) Continuation training (Procedures) 3.9 QUALIFICATION OF MAINTENANCE PERSONNEL (DASR 145.A.30(e), 35(a) to (g), (m), 65(d)) Suggested subject headings Experience (duration and technical), training and competence requirements Assessment procedures (Examination and Testing) Continuation training (Programme) Continuation training (Procedures) 3.10 AIRCRAFT OR COMPONENT MAINTENANCE TASKS, DEVIATION PROCESS CONTROL (DASR 145.A.45(c), (d), 48(i), 65(b)) Suggested subject headings: System for control and processing 3.11 CONCESSION CONTROL FOR DEVIATION FROM THE ORGANISATION'S PROCEDURES (DASR 145.A.65(b)) Suggested subject headings: System for approval and control of concession Concession criteria Request procedure Evaluation, response and approval 3.12 QUALIFICATION PROCEDURE FOR SPECIALISED ACTIVITIES SUCH AS NDT, WELDING ETC. (DASR 145.A.30(f) and 65(b)) Suggested subject headings: Experience, Training and Examination Continuation training and testing Auditing of staff and system 3.13 CONTROL OF MANUFACTURER'S AND OTHER MAINTENANCE WORKING TEAMS (DASR 145.A.30, 35, 40, 42, 43, 45, 48, 50, 55, 65) Suggested subject headings Sources of work Authorisation of personnel System for control of materials, Working instructions and procedures Control of documentation, drawings, modifications and repair instructions Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 36 of 52 Environmental conditions Certification: of repair, replacement, modification, overhaul and/or inspection Final certification by the AMO 3.14 HUMAN FACTORS TRAINING PROCEDURE (DASR 145.A.30(e), 35(d), (e), 65(e)) Suggested subject headings Aims and objectives Categories of employees to be trained Duration Requirements for trainers Training methods and syllabus Continuation training 3.15 COMPETENCE ASSESSMENT OF PERSONNEL (DASR 145.A.30(e), (f), 35(f), (g), (i), 65(b), (e)) Suggested subject headings Employees assessment standard Assessment procedures (training, qualifications, supervision and assessors) Management of competence assessments Assessment records Drug and Alcohol Management Plan 3.16 SAFETY MANAGEMENT SYSTEM (SMS) (DASR 145.A.65(b), (e)) Suggested subject headings Management commitment to, and responsibility for, safety risk management Safety accountabilities of managers Key personnel SMS implementation plan Third party relationships and interactions Emergency response plan Hazard identification — Risk management Monitoring, investigation, review and amendment of procedures Safety Promotion in the workforce Internal recording and analysis of safety data Safety assurance - Management of change - (Managing organisational changes should be considered with — Part 1, items 1.9 and 1.10) Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 37 of 52 PART 4 OPERATIONS This Part links the DASR 145 AMO to the Continuing Airworthiness Management Organisations for whom maintenance services are provided and should complement the CAMO’s own Continuing Airworthiness Management procedures, ensuring complete and accurate compliance to requirements for: recording of maintenance carried out; maintenance Certification, CRS and other records in the Continuing Airworthiness Records for aircraft; provision of Maintenance Records to the CAMO; communication with CAMO or person responsible for continuing airworthiness where appropriate; and retention of copies of Maintenance Records and CRS. Together, the two documents will define how the CAMO achieves safe operation by airworthy aircraft. Notes: 1. This Part need not be included if the organisation is not directly contracted to provide maintenance support for an CAMO. Such contracts are only likely to be found for the provision of aircraft or engine / APU maintenance. 2. Where this Part is not used it should be shown in the Exposition as Not Applicable 4.1 CONTRACTING/TASKING CAMO (DASR 145.A.70(a)13) Suggested subject headings List of CAMOs for whom maintenance is provided, with details of the types of aircraft (engines/APU) Scope of work undertaken, e.g. Base maintenance, Line maintenance, Defect rectification etc. with any limitations Details should show whether the contract is solely for carrying out maintenance or also for performing the CAMO maintenance management tasks. 4.2 CAMO PROCEDURES AND DOCUMENTATION (DASR 145.A.50(c), (e), 55(b)) This chapter must describe for each contracting Operating Organisation, the special mode of operation (procedures/ documents/ exchange of information, planning meetings, technical, quality, reliability) between the organisation and its customer. Suggested subject headings All tasks should be described, that are performed by the maintenance organisation to support the CAMO: º spares management procedures; º engine management programme; º reliability monitoring and data input to the CAMO Reliability program; º control of maintenance between Base maintenance inputs º daily technical log management º deferred and repetitive defect monitoring and reporting to the CAMO; Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 38 of 52 º º 4.3 aircraft external damage control — identification and control; and reporting of un-airworthy conditions etc CAMO RECORDS COMPLETION (DASR 145.A.55) Suggested subject headings Completing CAMO's log books Keeping the CAMO's technical records Retention of copy of CAMO records Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 39 of 52 PART 5 TRAINING AND ASSESSMENT This section should set out the procedures that the DASR 145 AMO must follow for the training and assessment of Certifying staff including: Note: 1. removing exclusions; utilising manufactures training for ratings; type and Task training for Category ‘A’ licence holders; and pilot and flight engineer training for maintenance permitted by the DASR M approved CAMO. AMO’s that deliver training for certifying employees should also refer to the relevant sections of DASR 66 and 147 related to the training and assessment to be conducted. 5.1 FACILITIES (DASR 145.A.25) Suggested contents Training facilities Instructional equipment Maintenance training material 5.2 PERSONNEL (DASR 145.A.30) Suggested contents Quality managers role Personnel responsible for training management Instructors Assessors Records of instructors and assessors 5.3 TRAINING AND ASSESSMENT PROCEDURES (DASR 145.a.30(e), (f), (g), 35(a), (d), (e), (f), (g), 65(b) Suggested contents Course plans Course material Conduct of training Exclusion training Aircraft system training Aircraft type training Conduct of assessment Aircraft type assessment Security of assessment material Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 40 of 52 5.4 TRAINING SOURCING AND QUALITY CONTROL (DASR 145.A.35(a), (b), (j), 65(b)) Suggested contents Sourcing manufacturers training Procedures to ensure training meets the standards required by DASRs 66 and 147 Aircraft type training Aircraft type assessment AMO Quality system interface with training 5.5 AUTHORISATION AND REPORTING (DASR 145.A.35 & 65(b)) Suggested contents Authorisation issue procedures Reporting procedures to DGTA-ADF 5.6 RECORDS (DASR 145.A.35(j), (k), (l), 65(b)) Suggested contents Student records Retention periods Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 41 of 52 PART 6 APPENDICES The lists shown may be kept as separate documents from the exposition as long as an adequate cross-reference is included in the exposition. 6.1 SAMPLE OF DOCUMENTS Suggested contents Goods Inwards Inspection Record (GRN) Serviceable, Unserviceable labels Register (or Card) of Precision Equipment and Tools Test Equipment "Calibration Due" Tag Controlled Manual / Service Information Identification AD control card / record Continued Airworthiness information (SB etc.) assessment record Maintenance Task Card (Scheduled Maintenance) Maintenance Task Card (Additional Defects) Life-limited parts/Out-of-Phase Work or Inspection-record Card Base Maintenance CRS Line Maintenance CRS DASR Form 1 or approved In-House Release form Un-airworthy Conditions Report Form Quality Audit Report Form Quality Audit Remedial Action Report Form Personnel Training Records Certifying Employees Authorisation Record Certifying Employees Personal Authority Training records and forms Concession Application and Approval Note: This is a typical list of company forms and is not intended to be exhaustive or to 1. represent the forms required for any particular organisation. The approved organisation must include those forms with which it controls and records its maintenance work and procedures. Alternatively, if the Forms are contained with the respective procedure, to which cross-reference is made in the Exposition it may be possible, by agreement with DGTA-ADF, to include here only the minimum of Forms needed to define the Approval conditions and limitations 6.2 LIST OF SUBCONTRACTORS (DASR 145.A.70(a)14, 75(b)) (If approval for the control of subcontractors is held by the organisation - see Part 1, items 1.8, 1.9, 1.10 and Parts 2.1 and 3.2) 6.3 LIST OF LINE MAINTENANCE LOCATIONS (DASR 145.A.75(d), 70(a)15) (If line maintenance locations are established by the organisation — see Part 1, items 1.7.2 and 1.8.1) Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 42 of 52 6.4 LIST OF CONTRACTED DASR 145 ORGANISATIONS (DASR145.A.70(a)16, 75(b)) (NDT contractors etc) Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 43 of 52 6.5 COMPLIANCE MATRIX This section may include a compliance matrix (example provided below) for the organisation to demonstrate how its exposition meets the requirements of DASR 145 DASR 145.A.10 145.A.10 145.A.15 145.A.15 145.A.20 145.A.20 145.A.25 145.A.25 145.A.25 (a) 145.A.25 (a) 1 145.A.25 (a) 2 145.A.25 (b) 145.A.25 (c) 145.A.25 (c) 1 145.A.25 (c) 2 145.A.25 (c) 3 145.A.25 (c) 4 145.A.25 (c) 5 145.A.25 (c) 6 145.A.25 (d) 145.A.30 145.A.30 (a) 145.A.30 (a) 1 145.A.30 (a) 2 145.A.30 (a) 3 145.A.30 (b) 145.A.30 (b) 1 145.A.30 (b) 2 145.A.30 (b) 3 145.A.30 (b) 4 145.A.30 (c) 145.A.30 (d) 145.A.30 (e) 145.A.30 (e) 145.A.30 (f) 145.A.30 (g) 145.A.30 (g) 145.A.30 (h) 145.A.30 (h) 1 145.A.30 (h) 1 (i) 145.A.30 (h) 1 (ii) 145.A.30 (h) 1 (iii) 145.A.30 (h) 2 145.A.30 (i) 145.A.30 (j) 145.A.30 (j) 1 145.A.30 (j) 2 145.A.30 (j) 3 145.A.30 (j) 4 Reference Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 44 of 52 145.A.30 (j) 5 145.A.30 (j) 5 (i) 145.A.30 (j) 5 (ii) 145.A.30 (j) 5 145.A.35 145.A.35 (a) 145.A.35 (a) 145.A.35 (b) 145.A.35 (c) 145.A.35 (c) 145.A.35 (d) 145.A.35 (e) 145.A.35 (f) 145.A.35 (g) 145.A.35 (h) 145.A.35 (h) 145.A.35 (i) 145.A.35 (j) 145.A.35 (j) 1 145.A.35 (j) 2 145.A.35 (j) 3 145.A.35 (j) 4 145.A.35 (j) 145.A.35 (k) 145.A.35 (l) 145.A.35 (m) 145.A.40 145.A.40 (a) 145.A.40 (a) 1 145.A.40 (a) 2 145.A.40 (a) 3 145.A.40 (b) 145.A.42 145.A.42 (a) 145.A.42 (a) 1 145.A.42 (a) 2 145.A.42 (a) 3 145.A.42 (a) 4 145.A.42 (a) 5 145.A.42 (b) 145.A.42 (c) 145.A.42 (d) 145.A.42 (e) 145.A.42 (f) 145.A.42 (g) 145.A.43 145.A.43 (a) 145.A.43 (a) 1 145.A.43 (a) 2 145.A.43 (a) 3 145.A.43 (a) 4 145.A.43 (a) 5 145.A.43 (b) 145.A.43 (c) Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 45 of 52 145.A.43 (d) 145.A.43 (d) 1 145.A.43 (d) 2 145.A.43 (e) 145.A.45 145.A.45 (a) 145.A.45 (a) 145.A.45 (b) 145.A.45 (b) 1 145.A.45 (b) 2 145.A.45 (b) 3 145.A.45 (b) 4 145.A.45 (b) 5 145.A.45 (c) 145.A.45 (d) 145.A.45 (e) 145.A.45 (e) 145.A.45 (f) 145.A.45 (g) 145.A.47 145.A.47 (a) 145.A.47 (b) 145.A.47 (c) 145.A.48 145.A.48 (a) 145.A.48 (b) 145.A.48 (c) 145.A.48 (d) 145.A.48 (e) 145.A.48 (f) 145.A.48 (g) 145.A.48 (h) 145.A.48 (i) 145.A.48 (j) 145.A.50 145.A.50 (a) 145.A.50 (b) 145.A.50 (c) 145.A.50 (d) 145.A.50 (e) 145.A.50 (f) 145.A.55 145.A.55 (a) 145.A.55 (b) 145.A.55 (c) 145.A.55 (c) 1 145.A.55 (c) 2 145.A.55 (c) 3 145.A.60 145.A.60 (a) 145.A.60 (b) 145.A.60 (c) 145.A.60 (d) 145.A.60 (e) Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 46 of 52 145.A.65 145.A.65 (a) 145.A.65 (b) 145.A.65 (b) 1 145.A.65 (b) 2 145.A.65 (b) 3 145.A.65 (b) 4 145.A.65 (c) 145.A.65 (c) 1 145.A.65 (c) 2 145.A.65 (d) 145.A.65 (e) 145.A.70 145.A.70 (a) 145.A.70 (a) 1 145.A.70 (a) 2 145.A.70 (a) 3 145.A.70 (a) 4 145.A.70 (a) 5 145.A.70 (a) 6 145.A.70 (a) 7 145.A.70 (a) 8 145.A.70 (a) 9 145.A.70 (a) 10 145.A.70 (a) 11 145.A.70 (a) 12 145.A.70 (a) 13 145.A.70 (a) 14 145.A.70 (a) 15 145.A.70 (a) 16 145.A.70 (b) 145.A.70 (c) 145.A.70 (d) 145.A.70 (e) 145.A.75 145.A.75 145.A.75 (a) 145.A.75 (b) 145.A.75 (c) 145.A.75 (d) 145.A.75 (e) 145.A.80 145.A.80 (a) 145.A.85 145.A.85 (a) 145.A.85 (a) 1 145.A.85 (a) 2 145.A.85 (a) 3 145.A.85 (a) 4 145.A.85 (a) 5 145.A.85 (a) 6 145.A.85 (a) 7 145.A.90 145.A.90 (a) Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 47 of 52 145.A.90 (a) 1 145.A.90 (a) 2 145.A.90 (a) 3 145.A.90 (b) 145.A.95 145.A.95 (a) 145.A.95 (b) 145.A.95 (c) 145.A.95 (c) 1 145.A.95 (c) 2 145.A.95 (c) 3 DASR SMS.A.25 SMS.A.25 (a) SMS.A.25 (b) SMS.A.25 (b).1 SMS.A.25 (b).2 SMS.A.25 (b).3 SMS.A.25 (b).4 Reference Issue: ................. Issue Date:…………. Version:………... Version Date:..……… Page 48 of 52
© Copyright 2026 Paperzz