DVI-7200-PS Series
Quick Start Guide
Distribution Power Supplies
Introduction
Many AV products require the use of external AC power supply units (PSU) to power their internal
electronic circuitry. These external PSUs (wall warts) can pose a major challenge to system designers as
they occupy valuable space within AV equipment racks where there are a limited number of AC outlets.
Furthermore, some external PSUs are poorly designed and ill-suited for use in high profile applications.
DVIGear’s DVI-7200-PS Series Distribution Power Supplies are engineered from the ground up for 24/7
mission critical applications. These units offer an unprecedented level of reliability with an MTBF of
greater than 100,000 hours. Even at full load these power supplies operate at less than 70% of their
rated maximum power, thus providing headroom that further enhances long-term reliability.
These units are housed in rugged 1U rack-mountable enclosures. They accept AC line voltages autoranging from 90-264 VAC and AC line frequencies from 47-63 Hz. Four models are available, with
output voltages of either +5VDC or +12VDC and a choice of either 10x or 20x outputs. All outputs
include extensive protection against overload, over-voltage and over-temperature. All outputs utilize
secure twist-lock DC power connectors. Several types of power supply extension cables are available
that support the full range of DVIGear products.
Typical Application
DVI-7235-PS
Distributed
Power
12
EO
VDC
OUT
VID
DDC
DVI
OUT
UT
INP
12
OR
D
EDI
VID
DDC
EO
RN
Y
VDC
ET
RES
MEM
D
I EDI
LEA
VGA
D
EDI
HDM
OUT
OUT
232
RS-
Note: power supply extension cable length is 5.2 ft. (1.6 m)
Distribution Power Supply
1
5
1
DVI-7235 Front View
2
6
3
4
DVI-7235 Rear View
DVI-7235 Rear View Close-up
2
7
Distribution Power Supplies
Quick Start Guide
DVI-7200-PS Series
1. Power LED
Continuously lit when unit is receiving power and switched ON.
2. AC Power Input
Connect supplied AC power cord securely to unit.
3.Power Switch
This switch turns the unit ON / OFF; lights green when turned ON.
4. DC Power Outputs (1)
+5 VDC Models
+12 VDC Models
10x Outputs
DVI-7220-PS
DVI-7230-PS
20x Outputs
DVI-7225-PS
DVI-7235-PS
5. Airflow Intake
Allows airflow into the device. (2)
6. Airflow Outlet
Two internal cooling fans output airflow here.(2)
7. Rack Mounting Ears
Rack-mountable in a standard 19-inch equipment rack.
Note 1: All DC outputs utilize locking connectors to
ensure secure connections and stable system operation.
Note 2: Warning, in order to ensure proper operation
and long term reliability, care must be taken to ensure
that the airflow is not restricted in any way.
Airflow Diagram
Installation
1.) Install the distribution power supply in a rack mount environment using mounting ears. Care
must be taken to ensure that the airflow is not restricted in any way. (2)
2.) Connect the AC power input cable to a power source and to the distribution power supply.
3.) Connect devices to be powered to the DC outputs of the unit using the appropriate power
supply extension cables, see page 4. (3)
4.) Turn the distribution power supply on using the Power Switch at the rear of the unit. Check to
make sure the power LED on the front panel is lit and the cooling fans are operating.
5.) The unit is ready for use.
Note 3: Warning: Models DVI-7230-PS and DVI-7235-PS provide +12VDC outputs. Take care to avoid
connecting any 5VDC devices to these +12VDC outputs as this may cause damage and system failure.
3
Power Supply Extension Cables
Please install the appropriate power supply extension cables to connect the DC outputs of this unit to
the devices to be powered remotely. There are several types of cables available, which support the full
range of DVIGear products. These cables are not included and must be ordered separately.
Model No:
DVI-7220-PSX
Connections
+5VDC, 5.5 x 2.5 x 9.5mm
Length
5.2 ft. (1.6 meters)
Connectors A and B
Compatible with DVI-7220-PS / DVI-7225-PS, DVI-7206-PS
Model No:
DVI-7230-PSX
Connections
+12VDC, 5.5 x 2.0 x 9.5mm
Length
5.2 ft. (1.6 meters)
Connectors A and B
Compatible with DVI-7230-PS / DVI-7235-PS, DVI-7215-PS
Model No:
DVI-7209-PSX
Connections
+5VDC, 5.5 x 2.5mm to 3.5 x 1.35 x 9.5mm
Length
5.2 ft. (1.6 meters)
Connector A
Connector B
Compatible with DVI-7220-PS / DVI-7225-PS, DVI-7210-PS
Model No:
DVI-7330-PSX
Connections
+5VDC, 5.5 x 2.5mm to USB Micro-B
Length
5.2 ft. (1.6 meters)
Connector A
Connector B
Compatible with DVI-7220-PS / DVI-7225-PS, DVI-7330-PS
Locking DC Power Plug
Twist 90° clockwise to lock
DVIGear
1059 Triad Court, Suite 8,
Marietta, GA 30062
Toll Free: 888.463.9927
Tel: 770.421.6699
Fax: 770.234.4207
4
DVI-7200-PS_Series_QSG-01 / January.2014
[email protected]
www.dvigear.com