ROME BINDING
3
Adjust Your Toe Strap Position
Rome ConFormist toe straps have two mounting positions: forward and back. Prior to
mounting your bindings, press down on the ladder strap, slide it to the desired position,
and then pull into place. Repeat the same process on the strap’s mounting tab on the
inside of the binding.
5
MOUNTING YOUR
ARSENAL AND
STRUT BINDINGS
Set Your Canting with the Yes, I Cant System
Your 390 Boss, Madison and Targas come with canting options (3.5 degrees for the
Boss/Madison, and 2 and 3.5 for the Targa). Canting gives both more leverage over
the nose and tail, while making wider stances feel more comfortable. If you want
canting, simply switch out the 0-degree InBase pad with the canted options.
3.5 DEGREES
TECHNOLOGIES DIVISION
1
2 DEGREES
SETTING UP AND CUSTOMIZING YOUR
UNDERWRAP™ BINDINGS
Getting your boot centered on the midline of your binding and the midline of your
board is super important—with an UnderWrap binding you do it with heel hoop
adjustment, not disc adjustment. Loosen the screws that attach the heel section
(but don’t remove), slide the heel hoop to the proper sizing, and tighten all four
screws. See sizing below, which is imprinted on the inside of your UnderWrap
heel hoop:
S/M BINDING MODEL
BOOT SIZE
MOUNTING YOUR
4
1
Unscrew your InBase pad, lift the heel and slide it out towards the toe.
Mount Your Bindings—Pick Your Stance Width
and Stance Angles
Rome boards provide suggested Default Stances on all models, but many riders like
to pick their own. A good rule of thumb if you don’t know your preference is a little
wider than shoulder width apart. For freestyle boards, most riders mount their bindings
centered on the board, whereas a lot of freeriders mount 20 mm back from center. Next
come the angles of your stance. Again, if you don’t know your preference a standard
“duck” stance is a good starting point: positive 15-degrees on your front foot and a
negative 9-degrees on your back foot. Once your position and angles are determined,
mount each binding with four disc screws.
New Channel Adjust for Centering Your Boot
0 DEGREES
Remove Your InBase Pad
3
Mount Your Bindings—Pick Your Stance Width
and Stance Angles
Rome boards provide suggested Default Stances on all models, but many riders like
to pick their own. A good rule of thumb if you don’t know your preference is a little
wider than shoulder width apart. For freestyle boards, most riders mount their bindings
centered on the board, whereas a lot of freeriders mount 20 mm back from center. Next
come the angles of your stance. Again, if you don’t know your preference a standard
“duck” stance is a good starting point: positive 15-degrees on your front foot and a
negative 9-degrees on your back foot. Once your position and angles are determined,
mount each binding with four disc screws.
6
MENS SIZING
4-9
WMNS SIZING
5.5-10.5
Mounting Your InBase pad
Slide in your InBase pad from the toe, line up the set screw and half tighten it.
L/XL BINDING MODEL
Slide your InBase pad toe-to-heel to center it on your board.
BOOT SIZE
MENS SIZING
9-12+
4
5
Tighten your set screw.
2
Adjust Your Toe Ramp to Your Boot
Put your boot in your binding and make sure your toe ramp matches the curve in the
toe area of your boot’s sole. Adjust if necessary.
Attach Your Disc Cover Set Screw
mounting disc.
New Channel Adjust for Centering Your Boot
Getting your boot centered on the midline of your binding and the midline of your board is super important—with an UnderWrap binding you do it with heel hoop adjustment, not disc adjustment.
Loosen the screws that attach the heel section (but don’t remove), slide the heel hoop to the proper sizing, and tighten all four screws. See sizing below, which is imprinted on the inside of your
UnderWrap heel hoop:
S/M BINDING MODEL
L/XL BINDING MODEL
BOOT SIZE
MENS SIZING
4-9
WMNS SIZING
5.5-10.5
BOOT SIZE
MENS SIZING
9-12+
2
Adjust Your Toe Strap Position
Rome ConFormist toe straps have two mounting positions: forward and back. Prior to
mounting your bindings, press down on the ladder strap, slide it to the desired position,
and then pull into place. Repeat the same process on the strap’s mounting tab on the
inside of the binding.
#3: All screw adjustments on Rome SDS UnderWrap bindings
are made with a #3 Phillips screwdriver.
ROME BINDING
TECHNOLOGIES DIVISION
2
Highback Rotation
3
Ankle Strap Flex Adjustment (only on Targa)
On the Targa’s PF Adjust Ankle Strap, if you want customize your instep support and
5
of rotation: 0°, 4°, 8°, and 12°. Rotation adjustments are made by using the two
mounting holes in each wing of the highback, and the three highback mounting holes
on the heel hoop. To rotate your highback, remove the highback mounting screws and
re-position using the combinations of the mounting holes in the highbacks and the
mounting holes in the heel hoop.
ConFormist Toe Strap Positioning
Rome ConFormist toe straps let riders locate their toe strap in multiple positions on their
boots: anywhere from over-the-boot to over-the-toe. In the over-the-toe position, Rome
market.
RIGHT FOOT EXAMPLE
HEELHOOP LEFT SIDE
POSITION - MIDDLE
HEELHOOP RIGH SIDE
POSITION - MIDDLE
HEELHOOP LEFT SIDE
POSITION = MIDDLE
CUSTOMIZING YOUR UNDERWRAP™ BINDINGS
1
Ankle Strap Position
Rome bindings provide three ankle strap mounting positions on both sides of the heel
position for a medium level of support, or mount in the rear position for the maximum
amount of support.
0
FORWARD - SOFTEST FLEX
HIGHBACK LEFT SIDE
POSITION = FRONT
HIGHBACK RIGHT SIDE
POSITION - FRONT
HIGHBACK LEFT SIDE
POSITION - BACK
0
6
4
HEELHOOP LEFT SIDE
POSITION - MIDDLE
HEELHOOP RIGH SIDE
POSITION - MIDDLE
HIGHBACK LEFT SIDE
POSITION - FRONT
MIDDLE - MEDIUM SUPPORT
QuickStrap Ankle and Toe Strap Length Adjustment
Rome’s QuickStrap.2 technology gives riders tool-free power to precisely place their ankle
Zero-to-24 Forward Lean Adjustment
Having a zero-degree forward lean option is critical in a binding—many freestyle riders
like their highbacks straight up and down for balance. A high range up to 24-degrees is
critical as well—many other riders like immediate support for laying into heelside turns.
Rome bindings deliver the best of both worlds and leave the choice up to you. Tool free.
HEELHOOP LEFT SIDE
POSITION = MIDDLE
the quick lever. Position strap so that it sits centered on your boot and close the quick
lever. Bang.
HIGHBACK LEFT SIDE
POSITION = BACK
HIGHBACK RIGHT SIDE
POSITION - BACK
4
0
HEELHOOP LEFT SIDE
POSITION - BACK
HEELHOOP RIGH SIDE
POSITION - FRONT
HEELHOOP LEFT SIDE
POSITION = FRONT
7
Using the NEW Convert Disc
Rome’s new Super Disc is designed to mount to both 4-hole boards and single-channel
boards. For the single-channel mode, use the two individual holes on the disc, not the
elongated holes for 4-hole boards.
HIGHBACK LEFT SIDE
POSITION - BACK
SINGLE-CHANNEL MODE
HIGHBACK RIGHT SIDE
POSITION - FRONT
4-HOLE MODE
HIGHBACK LEFT SIDE
POSITION = FRONT
REAR - MAXIMUM SUPPORT
80
HEELHOOP LEFT SIDE
POSITION - BACK
HEELHOOP RIGH SIDE
POSITION - FRONT
HIGHBACK LEFT SIDE
POSITION - FRONT
*FOR LEFT FOOT HIGHBACK ROTATION,
SIMPLY MIRROR THESE INSTRUCTIONS
HIGHBACK RIGHT SIDE
POSITION - BACK
HEELHOOP LEFT SIDE
POSITION = FRONT
If you still use a 3-hole board, the included disc won’t mount your bindings. Simply contact [email protected] and we’ll get you set up with a free set of the original Convert Disc.
HIGHBACK LEFT SIDE
POSITION = BACK