TECHNICAL DATA SHEET
SICO 232-XXX
EXTERIOR SOLID-COLOUR WOOD STAIN
Water-based product, satin finish
Product Description
Exterior water-base solid stain specially recommended for pressure-treated wood,
pine and even weathered for more than a year composite woods. Ideal for decks,
stairs, railings, sidings, fences and outdoor furniture. Excellent adhesion on old
well-prepared finishes: paint, solid and semi-transparent stains (except for waterrepellent stains containing wax).
Quality
Satisfactory performance standards
Advantages
• Satin matte finish when viewed straight on and soft lustre finish when viewed at
a grazing angle.
• Contains penetrating natural oils providing optimum protection against flaking.
• Acrylic formula that preserves the beauty of the wood.
• Water-based microporous product allowing wood to breathe.
• Dries rapidly, odour free
• Ready for use and easy to apply.
• Withstands the effects of weather without fading, halking, blistering, peeling or
cracking.
• Excellent resistance to mildew.
• A water-based product which allows an easy tool clean-up with water.
• Low VOC content complies with the Canadian Volatile Organic Compound (VOC)
Concentration Limits for Architectural Coatings Regulations requirements.
Projects
Environment
Exterior only.
Use
New and maintenance work.
Residential sites.
Ideal for decks, stairs, railings, sidings, fences and outdoor furniture.
Surfaces
Pressure-treated wood, pine, cedar or even composites woods weathered for
more than a year.
Notes
The moisture content of wood must be between 12% and 18%.
This product is incompatible with preservatives and waterproof semitransparent
stains containing wax.
Not to be used on burnt wood.
This product is not to be mixed with other paints, stains or thinners.
Technical Specifications (21°C (70°F))
Appearance
Opaque
Gloss Level
Satin finish
• Gloss at 60°: 5 to 15%
• Gloss at 85°: Not available
Composition
• Diluent: Water
• Binder: Acrylic-polymer and linseed oil emulsion
Drying Time*
• Touch dry: 4 hours
• Before recoating: 24 hours
• Prior to withstanding rain: 24 hours
• Prior to light circulation: 24 hours
• Prior to normal circulation: 3 days
• Before replacing the furniture: 3 to 7 days
• Before cleaning: 7 days
When relative humidity is higher than 50%, double
the required drying time.
Spreading Rate per Coat
3.78 L: 46 to 56 sq. m (500 to 600 sq. ft.)
(Excluding losses caused by variations in application
methods or surface porosity).
Volatile Organic Compounds (VOCs)*
According to ASTM D3960-05: < 150 g/L
Canadian regulation: < 250 g/L
Solids by Volume*
37%
Flammability
Non flammable
Minimal Film Thickness*
(According to the maximum spreading rate)
• Wet: 2.7 mils (69 μm)
• Dry: 1.1 mils (28 μm)
Certifications*
Not available
Akzo Nobel Canada Inc. guarantees performance of its products to its intended use if properly applied in accordance with the label
directions and the specifications of the technical data sheet. Having no control over the application methods and conditions or the
circumstances related to its use, no other guarantee, expressed or implied, statutory or otherwise is given. We shall not be
responsible for any indirect, consequential or other damages.
*Technical data source: 232-100
Edition of 2012-12-11
Surface Preparation
Surfaces must be clean, solid, dry and free from dust, dirt, oil, soot, wax, mildew,
chalking, loose stain or all other contaminants.
► Clean surface with Polyprep® cleaner 771-135, 771-136, or the appropriate
cleaner for removing the contaminant. Rinse well.
─ Remove mildew with a solution of household bleach (1 part household bleach to
3 parts of water). Wear rubber gloves and eye protection. Rinse thoroughly with
clear water.
► New wood or bare weathered wood: Clean with exterior wood cleaner,
brightener and conditioner Sico® 771-222, 771-333 or 771-666 or an appropriate
cleaner, rinse well with clear water.
► Surfaces in poor condition: Depending on the condition; remove all stain with a
stripper, a pressure jet or by scraping. Clean with exterior wood cleaner,
brightener and conditioner. Rinse well with clear water.
► Surfaces previously treated with a waterproof product containing wax: Strip the
surface.
► Sand horizontal surfaces using No. 80-grit sandpaper and vertical surfaces
using No. 120 grit sandpaper.
► Eliminate sanding residues.
Precaution: Dry sanding, flame cutting and/or welding of dry stain film will give
rise to dust and/or hazardous fumes. Wet sanding should be used, wherever
possible. If exposure cannot be avoided by the provision of local exhaust
ventilation, suitable respiratory protective equipment should be used.
► Previously stained wood in good condition: Wash well and rinse well.
► Repair holes and cracks with a suitable filler for the surface.
─ If wood exudes resin, scrape the excess and clean surface with alcohol or paint
thinner. On bare wood, seal knots with shellac Polyprep 205-112 before applying
the primer.
► Once the surface is free of any contaminant, wait 16 hours after light rain and
24 hours after moderate or heavy rain or pressure jet washing before to apply the
product under the recommended conditions of application.
► Moisture content of the wood must be between 12% and 18%.
• Bare wood: To prevent tannin bleeding of knotty or reddish coloured wood with
natural dyes, initially apply one or two coats of GoPrime® primer 150-135. Two
coats are required for pastel shades.
• Previously stained wood in good condition: Wash well with an appropriate
cleaner. Sand lightly with #80 sandpaper.
Application
This is a ready-to-use product, do not thin. Stir thoroughly the product before and
during application.
Pour the quantity of stain needed into another container to avoid contaminating
the original container. Keep containers closed when not in use.
Apply generously, leaving no bare spots or excessively coated areas in the direction
of wood grain to ensure colour uniformity.
Comply the product's spreading rate.
To avoid lapping, only handle a few boards at a time. Generously saturate the ends
of the boards.
Observe drying time between coats. Low temperatures or high humidity will affect
drying time. Applying two finishing coats will provide better durability and
appearance.
Wait 3 to 7 days before replacing furniture on the deck.
For more information on application methods, visit the website at www.sico.ca or
call our customer service: 1-800-463-7426.
This technical data sheet, No. 232-XXX, replaces all earlier versions.
Sico, Polyprep and GoPrime are registered trademarks of AkzoNobel Canada Inc.
Recommendations
Application Conditions
Temperature: 10 to 32°C (50 to 90°F)
(ideal 20°C ± 5°C [68°F ± 9°F]).
Relative humidity: Ideal between 15 and 50%,
maximum 85%.
Do not apply when dew is imminent, under
direct sunlight, on a warm surface or during
windy conditions.
Application conditions must be maintained
during paint application and drying.
Do not apply if lower temperatures are
expected within 3 to 6 hours.
Do not apply when rain is expected within 24
hours.
High humidity or low temperatures extend
drying time.
Tools
• Paintbrush: Synthetic bristles (nylon,
polyester) 10 mm (3/8 in.).
If rolling, back brush immediately on the
surface.
Cleaning Tools
Remove as much product quantity as possible
and clean tools with lukewarm water and soap
immediately after use.
Surface Maintenance
• Let surface dry completely and wait at least
7 days before cleaning.
• High and continuous moisture content,
insufficient ventilation of wood or high traffic
areas (decks) prematurely affect the product
performance.
Storage and Transportation
Keep in a dry and ventilated area, between 10
and 30°C (50° and 86°F).
Disposal
Consult your municipality about proper
disposal procedure of residue in accordance
with the laws and respect the environment or
give leftover stain to someone who could use
it: a neighbour or friend, a recreation centre or
a non-profit organization. Do not empty into
drains.
Safety Measures
Read the Material Safety Data Sheet. Avoid
contact with eyes. Keep out of reach of
children.
FIRST AID TREATMENT: If in contact with
eyes, rinse thoroughly with clear water. If
swallowed, do not induce vomiting. Call poison
centre or physician immediately.
Edition of 2012-12-11
Page 2 of 2