SMT-multifunction manifold
SITEK - MULTIFUNCTION MANIFOLD
WITH 41mm SPACING
Assembly and supply manifold for
solenoid valves, rotameters and other
pneumatic devices.
Individual shut-off in each output
facilitates safe on-line service or
modification with pressure on.
Suitable for the most manufacturers’
solenoid valves.
Manifold can also have laser marked
position marks.
TECHNICAL DATA
Suitable fluids
Input
Outputs
Number of outputs
Temperature range
Operating pressure
Material
Outputs can be equipped with ball valves.
Dry or lubricated air or gas
1/2" R/G or NPT
1/8”, 1/4", 3/8”, R/G or NPT
4, 6, 8, 10, 12, 15 available for 41mm spacing
- 20 ... + 90 º C
Vacuum ... 16 bar (232 psi)
Anodised aluminium and nickel plated brass
Standard construction: individual shut-off valves, brackets, double nibble and end cap. End thread is always 1/2".
Manifold with NPT-thread: the character R to be replaced with N.
TYPE CODE
SMT R 12/41N - 1/4 - 65
140
© 2014 Sitek-Service Ltd.
G/R R
NPT N
Number of outputs
4 6 8 10 12 15
Example: Multifunction Manifold SMT…/41 41mm spacing, R-thread, 12 outputs/hand knob N, 1/4” output thread,
bracket height 65 mm.
Patented product.
Sitek-Service Ltd
Laukaantie 4
Hatanpäänvaltatie 34 A
E-mail: [email protected]
40320 Jyväskylä
33100 Tampere
www.sitek.fi
Finland
Finland
Tel. +358 14 337 2300
Tel. +358 3 265 4069
All rights reserved.
Thread
Thread
Bracket height
65 50
120
Output
1/8” 1/4” 3/8”
SMT41-EN-0414
Series
Dimensions
Shut-off valve 1/2" ( SPV- )
( Optional )
Pressure gauge Ø 50 mm ( SPM- )
( Optional )
E
30
10
140
40
46
Shut-off valve 1/4" ( SPV- )
( Optional )
1/8"
1/4"
3/8"
94
89
2
L1
35
1/2"
L2
20
13
20
60
Adapter 1/2" ( SKP- )
( Optional )
L
100
DIMENSIONS
Outputs
Length L/mm
Spacing E/mm
2
95
41
4
177
41
6
259
41
8
341
41
10
423
41
12
505
41
15
628
41
Attn. Adapter ½” only available for standard SMT Manifold with 33mm spacing.
120
65
SAJ - 65
60
SAJ - 120
L1
L2
FITTING MOUNTING
1. The Shut-Off Stem must be closed (lower position) when
connecting or removing equipment.
3
Locking
2. Turn the Assembly Bolt to install or remove equipment.
Elbow
17 mm
Fitting
1
2
3
3. The Locking Ring will lock the Assembly Bolt. No extra
plugs needed.
4. The Fitting must be tightened slightly towards the elbow.
This allows free rotation of the assembly and prevents
the tube from being bent.
Seal the Fitting with glue (O-ring does not work as
sealing in this case).
Do not tighten too heavy, the Fitting will not tighten itself
against the manifold body (elbow damage).
Device
Warning: Maximum tightening torque for assembly bolt 30 Nm (3 kpm)
www.sitek.fi
All rights reserved.
Closed
© 2014 Sitek-Service Ltd.
USING THE OUTPUT PORT
SMT41-EN-0414
DEVICE MOUNTING
Open
* Example
with Asco Numatics
L1...L2 - series valves
160 (L1)*
168 (L2)*
215 (L1)*
223 (L2)*