LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
1
Product name
Description
Version
AW-0707
Datasheet of AW-0707 WLAN SiP module
1.0
Introduction
LOCOSYS AW-0707 is a System-in-Package (SiP) Module that integrates Atheros AR6003G
802.11b/g/n WiFi solution. This embedded module is optimized for the size, performance and power
consumption needed for mobile and embedded devices. With its tiny footprint and energy-saving qualities, the
AW-0707 rounds out Atheros’ comprehensive Align® ecosystem of 1-stream 802.11n solutions, targeting
tablet PC, mobile gaming and portable consumer electronic devices.
The new ROCm® AR6003 enhances its rate-over-range performance above the coverage improvements
inherent in the 802.11n MAC and PHY, by leveraging advanced optional 11n features such as Space Time
Block Coding (STBC) and low density parity check (LDPC). In addition, the AR6003 features Atheros
Universal Wireless Cooperation™, a suite of advanced wireless coexistence techniques to significantly
enhance the simultaneous operation of WLAN and Bluetooth on a mobile device.
2
Features
3
IEEE Standard 802.11 b/g/n compliant
Advanced 1x1 802.11n features
Frequency Band: 2.4GHz
Host Interface: SDIO 2.0
Lowest power consumption with near zero in idle/standby modes.
Small form factor 7 x 7 x 1.1 mm
RoHS compliant
Application
Mobile WLAN/AP
WiFi positioning with Atheros GPS
APC Hero
01480 226600
[email protected]
Page 1/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
Fig 3-1 System block diagram.
APC Hero
01480 226600
[email protected]
Page 2/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
Fig 3-2 Typical application circuit (WiFi only)
APC Hero
01480 226600
[email protected]
Page 3/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
4
RF Specification
4.1 Wireless specification
The AW-0707 module complies with the following features and standards;
Features
Description
WLAN Standards
IEEE 802 Part 11b/g/n (802.11b/g/n single stream n)
Antenna Port
Support Single Antenna for WiFi
Frequency Band
2.400 – 2.484 GHz
The RF performance of AW-0707 is given as follows. The default voltage is 3.3V.
Features
Description
Frequency Band
2.4000 – 2.497 GHz (2.4 GHz ISM Band)
Number of selectable Sub
channels
Modulation
Supported rates
Maximum receive input level
14 channels
OFDM, DSSS (Direct Sequence Spread Spectrum), DBPSK, DQPSK,
CCK , 16QAM, 64QAM
1,2, 5.5,11,6,9,12,24,36,48,54 Mbps
- 10dBm (with PER < 8%@11 Mbps)
- 20dBm (with PER < 10%@54 Mbps)
16 dBm +2.0/-2.0 dB for 802.11b ( @ 1,2,5.5,11 M bps)
14 dBm +2.0/-2.0 dB for 802.11g ( @ 6~54M bps)
Output Power
15 dBm +2.0/-2.0 dB for 11n ( @MCS0~3,HT20)
14 dBm +2.0/-2.0 dB for 11n ( @MCS4~5,HT20)
13 dBm +2.0/-2.0 dB for 11n ( @MCS6,HT20)
12 dBm +2.0/-2.0 dB for 11n ( @MCS7,HT20)
Carrier Frequency Accuracy
+/- 20ppm
(crystal: 26MHz +/-10ppm in 250C)
Condition: VBATT =VBATT2= DVDD_SDIO=VDD33=DVDD_SOC1= DVDD_SOC2= HMODE0=
HMODE1=3.3V, VDD18=1.8V.
APC Hero
01480 226600
[email protected]
Page 4/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
4.2 WiFi RF Transmitter Specification
802.11b Transmit
Item
Condition
Min.
Typ.
Max.
Unit
Transmit
11M/5.5M/2M/1M
14
16
18
dBm
20
ppm
-40
-30*
dBr
-55
-50*
dBr
10% ~ 90 %
0.3
2*
us
90% ~ 10 %
1.5
2*
us
1/2/5.5/11 Mbps
-17
-10
dB
output power
11M Mask compliant
level
19
Transmit
center
-20
frequency
tolerance
Fc-22MHz<F<Fc-11MHz &
Fc+11MHz<F<Fc+22MHz(1/2/5.5/11Mbps;
Transmit
channel 1~13)
spectrum mask
F<Fc-22MHz & F>Fc+22MHz(1/2/5.5/11Mbps;
channel 1~13)
Transmit
power-on
Transmit
power -down
Transmit
modulation
accuracy
“*” indicates IEEE802.11 specification
APC Hero
01480 226600
[email protected]
Page 5/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
802.11g Transmit
Item
Condition
Min.
Typ.
Max.
Unit
Transmit output
6~54Mbps
12
14
16
dBm
power level
54M EVM compliant
0
20
ppm
54Mbps
-28
-25*
dB
48Mbps
-28
-22*
dB
36Mbps
-23
-19*
dB
24Mbps
-23
-16*
dB
18Mbps
-15
-13*
dB
12Mbps
-15
-10*
dB
9Mbps
-10
-8*
dB
6Mbps
-10
-5*
dB
@ 11MHz
-27
-20*
dBr
@ 20MHz
-40
-28*
dBr
@ 30MHz
-54
-40*
dBr
16
Transmit center
-20
frequency
tolerance
Transmit
modulation
accuracy
Transmit spectral
mask
802.11n Transmit
Item
Transmit output
power level
Condition
Min.
Typ.
Max.
Unit
HT20 MCS 0~3
13
15
17
dBm
HT20 MCS 4~5
12
14
16
HT20 MCS 6
11
13
15
HT20 MCS 7
10
12
14
HT20 EVM Compliant
15
Transmit center
frequency
-20
0
20
ppm
HT20, MCS0
-10
-5*
dB
HT20, MCS7
-28
-28*
dB
@ 11MHz
-27
-20*
dBr
@ 20MHz
-40
-28*
dBr
@ 30MHz
-54
-40*
dBr
tolerance
Transmit
modulation
accuracy
Transmit
Spectrum mask
“*” indicates IEEE802.11 specification
APC Hero
01480 226600
[email protected]
Page 6/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
4.3 WiFi RF Receiver Specification
802.11 b Receiver
Item
Condition
Min.
Typ.
Max.
Unit
-86
-81
-77
dBm
5Mbps
-84
-80
dBm
2Mbps
-86
-82
dBm
1Mbps
-90
-86
dBm
-10
dBm
11Mbps
Receiver minimum input
level sensitivity
(PER< 8 % )
Receiver maximum input
level sensitivity
1/2/5.5/11 Mbps
(PER< 8 % )
802.11g Receiver
Item
Condition
Min.
Typ.
Max.
Unit
54Mbps
-73
-70
-66
dBm
48Mbps
-69
-67
dBm
36Mbps
-76
-72
dBm
24Mbps
-76
-72
dBm
18Mbps
-82
-78
dBm
12Mbps
-84
-80
dBm
9Mbps
-86
-82
dBm
6Mbps
-86
-82
dBm
-20
dBm
Receiver minimum input
level sensitivity (PER<10
%)
Receiver maximum input
level (PER<10%)
6/9/12/18/24/36/48/54
“*” indicates IEEE802.11 specification
APC Hero
01480 226600
[email protected]
Page 7/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
802.11n Receiver
Item
Condition
Receiver minimum input
level sensitivity (PER<10
%)
Min.
Unit
-85
dBm
HT20, MCS1
-82
dBm
HT20, MCS2
-80
dBm
HT20, MCS3
-75
dBm
HT20, MCS4
-73
dBm
HT20, MCS5
-68
dBm
HT20, MCS6
-66
dBm
-65
dBm
-70
6/9/12/18/24/36/48/54
level (PER<10%)
Max.
HT20, MCS0
HT20, MCS7
Receiver maximum input
Typ.
-20
dBm
“*” indicates IEEE802.11 specification
5
Pin assignment and descriptions
Table 5-1 Pin descriptions
Connection to IC
Terminal
Pin #
Pin Name
type
Power
1
DVDD_SDIO
P
-
DVDD_SDIO
Host interface I/O supply
2
PAREG_CAP
-
-
-
-
3
VDD33
P
-
-
Power supply input to AR6003
4
BT_PRIORITY
-
DVDD_SOC1 GPIO3
BT_PRIORITY signal from BT
chip
5
BT_ACTIVE
-
DVDD_SOC1 GPIO2
BT_ACTIVE signal from BT
chip
6
BT_FREQUENCY
-
DVDD_SOC1 GPIO0
BT FREQUENCY signal from
BT chip
7
BT_CLK_REQ
I
DVDD_SOC1 GPIO24
Clock request signal from BT
chip
8
BT_CLK_OUT
O
DVDD_SOC1 GPIO23
Reference clock output to BT
chip
DVDD_SOC1 GPIO25
CLK_REQ signal indicating
when a reference clock is
needed.
9
CLK_REQ_OUT
APC Hero
01480 226600
[email protected]
O
Description
Page 8/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
10
WLAN_ACTIVE
-
11
GND
-
12
XTALI
O
DVDD_SOC1 GPIO1
-
-
WLAN ACTIVE signal to BT
chip
-
Ground
XTALI
Can support
19.2/24/26/38.4/40/52 MHz,
characterized with 26 and 19.2
MHz
13
XTALO
I
-
XTALO
Can support
19.2/24/26/38.4/40/52 MHz,
characterized with 26 and 19.2
MHz
14
GND
-
-
-
Ground
15
DVDD_SOC1
P
-
DVDD_SOC1
SOC1 GPIO I/O supply
16
GND
-
-
-
Ground
Power supply input to digital
core and analog circuit
17
VDD18
P
-
VREG
VDD18_SYNTH
VDD18_RF
VDD18_BB
18
GND
-
-
-
Ground
19
ANT
I/O
-
-
RF transmitter output and RF
receiver input
20
GND
-
-
-
Ground
21
BT_RF
I/O
-
-
Connect to Bluetooth RF trace
22
GND
-
-
-
Ground
23
GND
-
-
-
Ground
24
GND
-
-
-
Ground
25
TDO
O
DVDD_SOC2
GPIO8
JTAG TDO output
26
HMODE1
I
DVDD_SOC2
GPIO20
Connect to DVDD_SOC2
27
WOW
O
DVDD_SOC2
GPIO22
Wake on wireless output
28
GND
-
-
Ground
29
UART_RX
I
30
HMODE0
I
31
UART_TX
O
APC Hero
01480 226600
[email protected]
-
DVDD_SOC2 GPIO17
DVDD_SOC2
GPIO19
DVDD_SOC2 GPIO15
For debug
Connect to DVDD_SOC2,
WLAN host interface setting:
0 : GSPI mode
1 : SDIO mode
For debug
Page 9/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
32
NC
-
-
-
NC
33
GND
-
-
-
Ground
34
CLK32K
I
35
VDD33
P
36
DVDD_SOC2
P
37
SDIO_D1
I/O
38
SDIO_CLK
39
DVDD_SOC2 GPIO21
-
Optional external input sleep
clock. Connect to ground when
using internal clock.
VDD33_ANT
VDD33_PA
Antenna control I/O Supply ,and
Internal EPA(Efficient PA)
Supply
DVDD_SOC2
SOC2 GPIO I/O supply
DVDD_SDIO SDIO_D1
SDIO data pin bit 1 (also GSPI
host interrupt)
I
DVDD_SDIO SDIO_CLK
SDIO clock (also GSPI clock)
SDIO_CMD
I
DVDD_SDIO SDIO_CMD
SDIO command (also GSPI
MOSI)
40
SDIO_D0
I/O
DVDD_SDIO SDIO_D0
SDIO data pin bit 0 (also GSPI
MISO)
41
SDIO_D2
I/O
DVDD_SDIO SDIO_D2
SDIO data pin bit 2
42
SDIO_D3
I/O
DVDD_SDIO SDIO_D3
SDIO data pin bit 3 (also GSPI
CS)
43
CHIP_PWD_L
I
DVDD_SDIO CHIP_PWD
Chip power down input
44
GND
-
-
-
Ground
"type" Column: I=Input, O=Output, IO=Bi-directional
APC Hero
01480 226600
[email protected]
Page 10/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
6
Addition information
6.1 Power on/off Sequences
The following two figures show the recommended power up/down and reset sequences for
the AW-0707 using external 3.3V and 1.8V supplies.
Figure 6-1 Power-Up/-Down Timing
Figure 6-2 Reset and Power Cycle timing
Table 6-1 Timing Diagram Definitions
Symbol
Ta
Description
Min(us)
Time between VBAT, VDD33, and I/O supplies valid and 1.8V supply valid.
[1]
0
Tb
Time between 1.8V supply valid and CHIP_PWD_L deassertion.
5
Tc
Time between CHIP_PWD_L assertion and 1.8V supply invalid.
0
Td
Te
Time between 1.8V supply invalid and VBAT, VDD33, and I/O supplies
invalid.
Length of CHIP_PWD_L pulse.
N/A[2]
5
[1] Supply valid represents the voltage level has reached 90% level.
[2] No strict requirement. This parameter can also be negative.
APC Hero
01480 226600
[email protected]
Page 11/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
6.2 Low-Frequency/SLEEP/32 KHz Clock for WLAN
The 32KHz clock is used in low-power modes such as IEEE power-save and sleep. It
serves as a timer to determine when to wake up to receive beacons in various power-save
schemes and to maintain basic logic operations when in sleep:
If the end application has a more accurate 32.768KHz clock, then it can be supplied
externally via the pin34 CLK32K.
If an external 32kHz clock is used, the requirements are as follows:
Figure 6-2 and below table show the pin34 optional external 32.768 KHz input clock
timing requirements.
Figure 6-3 pin 34 CLK32K input clock timing
6.3 Reference Clock for WLAN
The AW-0707 requires an external reference clock input. Supported frequencies for this
clock are 19.2, 24, 26, 38.4, 40, and 52MHz. The default frequency supported by software is
26MHz. When using a TCXO, the clock signal is input at the XTALO pin and must be
AC-coupled using a 0.01uF capacitor. The XTALI pin must be tied to GND when using a
TCXO.
Figure 6-4 and Table show the external 19.2/24/26/38.4/40/52 MHz reference input clock
timing requirements. The reference clock requirements are as follows:
The external reference clock option or host reference drive option voltage requirements are
shown as Fig 6-3
APC Hero
01480 226600
[email protected]
Page 12/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
Figure 6-4 External 19.2/24/26/38.4/40/52 MHz
Symbol
Description
Min.
Nom.
Max.
Unit
CK2
Fall Time
-
-
0.1*Period
ns
CK3
Rise Time
-
-
0.1*Period
ns
40
60
%
20
ppm
3.46
V
Duty Cycle
CK4
(High-to-Low Ratio)
CK5
Frequency Stability
-20
CK6
Input High Voltage
0.75
CK7
Input Low Voltage
-
V
6.4 Pin Settings for Mode Configuration
GPIO19
GPIO20
Description
0
1
GSPI Mode. Do not use because the software driver
is not ready.
1
1
SDIO Mode
6.5 SDIO/GSPI Interface Timing
Figure 6-5 GSPI Timing
APC Hero
01480 226600
[email protected]
Page 13/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
Figure 6-6 SDIO 2.0 Timing
SDIO Timing Constraints
Parameter
Description
Min.
Max
Unit
fPP
Clock frequency data transfer mode
0
50
MHz
tWL
Clock low time
7
ns
tWH
Clock high time
7
ns
tTLH
Clock rise time
10
ns
tTHL
Clock fall time
10
ns
tISU
Input setup time
6
-
ns
tIH
Input hold time
2
-
ns
tOH
Output hold time
2.5
-
ns
tO_DLY (min)
Output delay time during data transfer
mode
0
14
ns
Min.
Max
Unit
0
48
MHz
GSPI Timing Constraints
Parameter
Description
fPP
Clock frequency data transfer mode
tWL
Clock low time
8.3
ns
tWH
Clock high time
8.3
ns
tTLH
Clock rise time
2
ns
tTHL
Clock fall time
2
ns
tISU
Input setup time
5
-
ns
tIH
Input hold time
5
-
ns
APC Hero
01480 226600
[email protected]
Page 14/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
tO_DLY
7
Output delay
0
5
ns
DC & Temperature characteristics
7.1 Absolute maximum ratings
Supply Power
Max
Non Operating Temperature
- 40° to 85° Celsius
Voltage ripple
+/- 2%
Power Supply Absolute
Maximum Ratings
+4.35 Volt
Max. Values not exceeding Operating
voltage
Power
min
Max
VBATT
-0.3
4
VBATT2
-0.3
4
DVDD33
-0.3
4
DVDD_SDIO
-0.3
4
VDD18
-0.3
2.5
DVDD_SOC1
-0.3
4
DVDD_SOC2
-0.3
4
HMODE0
-0.3
4
HMODE1
-0.3
4
7.2 Recommendable Operation Condition
7.2.1 Temperature, Humidity
The AW-0707 module has to withstand the operational requirements as listed in the table
below.
Operating Temperature
-20° to 70° Celsius
Humidity range
Max
95%
Non condensing, relative humidity
7.2.2 Voltage
Power supply for the AW-0707 module will be provided by the host via the power pins
Symbol
Parameter
Min
Typ
Max
Unit
VBATT
VBAT Voltage
3.14
3.3
3.46
V
VBATT2
PA Voltage
3.2
3.3
4.2
V
DVDD_SOC1
GPIO I/O Supply
1.71
1.8
3.46
V
DVDD_SOC2
GPIO I/O Supply
1.71
1.8
3.46
V
DVDD_SDIO
DVDD I/O Supply
1.71
3.3
3.46
V
VDD33
I/O Supply
3.14
3.3
3.46
V
VDD18
1.8V I/O supply
1.71
1.8
1.89
V
APC Hero
01480 226600
[email protected]
Page 15/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
7.3 Current Consumption
Condition: VBATT =VBATT2= DVDD_SDIO=VDD33=DVDD_SOC1= DVDD_SOC2=
Hmode0= Hmode1=3.3V, VDD18=1.8V.
Item
Condition
Tx mode 11b
Tx 99% @11Mbps Tx 16dBm
1.8V
60
mA
VBATT
205
mA
1.8V
71
mA
VBATT
120
mA
1.8V
71
mA
VBATT
110
mA
1.8V
75
mA
VBATT
0.1
mA
1.8V
0.01
mA
VBATT
0.02
mA
Tx mode11g
Tx 99% @54Mbps Tx 14dBm
Tx mode 11n
Tx 99% @MCS7 Tx 12dBm
Rx mode(Rx @Max gain)
Sleep mode
APC Hero
01480 226600
[email protected]
Min
Nom
Max
Unit
Page 16/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
8
Mechanical specification
8.1 Weight
Min
Module’s Weight
Typ
Max
Unit
0.2
gram
8.2 Dimension
APC Hero
01480 226600
[email protected]
Page 17/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
8.3 Recommended land pattern dimensions
APC Hero
01480 226600
[email protected]
Page 18/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
Recommended Reflow profile
245+0/-5’c
Temperature
9
217’c
200’c
150’c
Time
APC Hero
01480 226600
[email protected]
Pre-heating
Soldering
90~120 sec
60~90 sec
Page 19/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
10 Reel Packing information
Reel(13”)*1, Carrier tape*25.5m, Cover tape*25.5m
APC Hero
01480 226600
[email protected]
Page 20/21
© 2010 LOCOSYS Technology Inc.
LOCOSYS Technology Inc.
20F.-13, No.79, Sec. 1, Xintai 5th Rd.,
Xizhi City, Taipei County 221, Taiwan
℡ 886-2-8698-3698
886-2-8698-3699
www.locosystech.com/
Document change list
Revision 1.0
First release on November 16, 2011.
APC Hero
01480 226600
[email protected]
Page 21/21
© 2010 LOCOSYS Technology Inc.