Celebrating 21
Years
2016
Why Dynapack
The answer is simple….sensitivity; repeatability; portability & reliability!
Our team has put a lot of hard work into developing this product and maintaining its sensitivity
& repeatability. The Dynapack gives you the ultimate in control for engine mapping and
development with RPM changes from 1RPM to whatever increment the user defines.
We use hydraulics. We do not use inertia, we do not use air, we do not use eddy currents, and we
do not use friction. Hydraulics are incredibly powerful, yet precise. We have total control of the
axle… Literally. By direct coupling to the hubs we eliminate the TYRE/ROLLER interface which
means NO WHEEL SLIP and therefore NO INERTIA to mask any small changes.
simulate
Simulate track conditions with user controlled rate of RPM or LOAD changes.
modular
The Dynapack is modular and all of our 2WD’s are easily upgraded to
4WD systems.
easy to use
Our software is extremely easy to use – Windows based platform, with
easily seen displays from the vehicle.
noise factors
The Dynapack is very quiet – all you hear is the vehicle during testing –
space saving
When the Dynapack is not in use simply ROLL IT OUT OF THE WAY or
safety factors
PERFECT FOR NVH TESTING.
under your work bench as there is no in-ground installation required.
The Dynapack is safe to use – NO ROLLERS – NO TIE DOWNS - FAR
LESS NOISE AND ABSOLUTELY NO TORQUE STEER. The Dynapack
supports the weight of the vehicle.
sensitivity
Measure minuscule differences when testing with a repeatable vehicle
(as not all vehicles are that repeatable) you can see .010” in a spark plug
gap; the differences between engine or driveline fluids; the alternator
load when the headlights or hazard lights are switched on.
repeatability
The Dynapack runs are repeatable to within three-tenth’s of one
percent.
portablilty
That’s right, the Dynapack is portable! Whether you want to move
premises, operate a mobile business; take it to another shop if moving
the vehicle is impractical or even take it to the track. You can test,
diagnose and load test the vehicles right in the pit.
Single phase power, low pressure cooling water & a fan is all you need to become
operational out of the box!
Custom Solutions
The Dynapack™ range of products is constantly being developed and
we’re constantly called upon to push the envelope with new and varied products.
Although most of our products are from the automotive world, the Dynapack™ range of
products have gained such a reputation worldwide, that we have been asked to make custom
solutions in other areas, such as sports and engineering.
Team New Zealand was one of these for whom we designed a grinding simulator for training
and analysis of fitness of each team member.
Custom solutions have also been built for use within the Army, Navy and Aeronautical industries.
DAQPLUS Smart Control
software features
AUTOPLOT (F1) - LAUNCH F3/SMG
LOAD MODE (F2)
F2 - 4WD TORQUE PROPORTIONING
SPEED MODE (F3)
DATA LOGGING & SHIFT+F4
This mode is intended to produce an
AutoPlot functionality that is allowed
under F11 AutoPlot set up.
This function is intended to provide a
load that you can hold the engine at and
test for acceleration and deceleration fuel
values and any associated temperatures
and pressures.
This function is intended to allow you to
set the front to rear torque values by for
the specific vehicle. It is then saved to
that vehicles folder for the next time. This
torque distribution is only available in
LOAD mode only.
This function is intended to be used for
holding any engine speed under load
for the purpose of defining a map or
loading the set rpm at any load up to
the limit of the torque specified for your
model Dynapack.
This feature allows you to see the
full NUMERIC DATA in columns. Your
column selection’s can be saved in
CONFIGURATIONS for future access.
PROGRAMMABLE DATA LOG
Programme your own test cycle selecting
a start RPM - finish RPM and transition
type and the time frame within this
programmable log. Add as many as you
need to create your own test cycle or
track simulation.
GAS ANALYSER
Easy view user interface with all data
available in the Strip graphs real time and
the user defined screen post processed.
The Dynapack Gas Analyser is fully
integrated with the DAQPLUS software.
NEW Software
Features
GEARBOX SETUP SCREEN
This screen allows you to capture the
individual gears and diff ratios. No scaling
is used on this screen. No dyno control is
used in this setup screen.
GEARBOX SIMULATION SCREEN
This screen shows the relationship
between TORQUE and RPM for all gears
and allows you to simulate a different
gearbox under the “WHAT IF” column.
*No Scaling is used on this screen*
Quarter Mile, Terminal Velocity, Gear
Changes, Acceleration vs Engine RPM,
Acceleration vs Speed and Engine
Acceleration Profile.
USER DEFINED SETS
This allows you to configure and
save multiple “QUICK VIEW” sets of
data relevant to a specific test. All
data is saved with the Vehicle’s Files
and is available when reviewed later.
There are several factory Pre Set Data
Sets - Quarter Mile, Terminal Velocity,
Gear Changes, Clutch/Torque Converter
Slip and Weather Station
Screen Information
AXLE TORQUE & AXLE POWER
Using cursers and zoom
allows you to check DELTA’s.
4WD TORQUE SPLIT
This graph will show you 4WD front
and rear axle torque.
TEMPERATURE GRAPH
This screen allows you to check that you
have not gone outside of your desired
temperature range when using standards
correction.
ACCELERATION (g’s)
Enter vehicle weight etc. In F11 and see
acceleration throughout your RPM range.
Screen Information
Continued.....
TORQUE & LAMBDA GRAPHS
This graph shows Engine Torque vs
Lambda.
GRAPH AUTO SCALE & MANUAL SCALE
With the exception of the USER DEFINED
DATA SET,
STATUS PANEL/HOME
SCREEN, STRIP GRAPHS & GEARBOX
SIMULATION GRAPHS all other graphs
accessed using the PAGE UP/PAGE
DOWN keys have “X” & “Y” axis scaling.
The default setting it AUTO SCALE,
however the COMPARISON screen is also
different with 2 x Y axis to scale.
COMPARISON SCREEN
Allows you to analyse your data and
compare one run against another. A solid
line is the SOURCE run and a dashed line
is the COMPARISON run imported from a
previous file.
Source AP1/AP2 will change relative to
the cursor position on the screen
What do you get in a
standard package?
Dynapack Cabinet with BUILT IN Controller and
PC with DAQPLUS SMART CONTROL SOFTWARE
Pre Loaded
WITH BUILT IN:
> DUAL LAMBDA
> DUAL MAP
> DUAL EGT INPUTS
> TEMPERATURE/
HUMIDITY
> AUTOMATIC
BAROMETRIC
SENSOR
> RPM INPUT*
> TPS INPUT*
* Supplied with cable
but NO Sensor
2 X PODS IN A 2WD SYSTEM with 2 individual pod cables
4 X PODS IN A 4WD SYSTEM with 4 individual pod cables
4 STUD HUB ADAPTOR SET (2 in 2wd set; 4 in 4WD set)
5 STUD HUB ADAPTOR SET (2 in 2wd set; 4 in 4WD set)
HUB ADAPTOR WASHERS
Optional Extras
48 CHANNEL DAQ MODULE
48 CHANNELS INCLUDE:
24 x VOLTAGE INPUTS
8 x FREQUENCY INPUTS
The benefits:
~ Simple way to add these data channels to older
versions of Dynapack
~ Additional Channels are viewable & recorded with
exisitng vehicle file information
This external DAQ Module is also available in 12 &
24 Channel Modules and is compatible* with any
Dynapack dynamometer.
8 x LAMBDA INPUTS
8 x EGT INPUTS
7 x THERMISTER INPUTS
*Latest Software is required
This external DAQ Module is compatible with any
Dynapack dynamometer.
OPTIONAL HUB ADAPTORS
6 STUD HUB ADAPTORS
UNIVERSAL HUB ADAPTORS
REVERSIBLE HUB ADAPTORS
EGT SENSOR
Exhaust Gas Temperature (EGT) measurement
is available on some controllers. If equipped,
the controller will have sockets labeled EGT like
these (Figure 1).
2WD Model Range
Model
DAQ2
DAQ3
DAQ4
DAQ5
HP Capacity
402
925
1233
1390
kW Capacity
300
690
920
1036
lb/ft Torque Capacity
1474
2212
2950
3319
Nm Torque Capacity
2000
3000
4000
4500
Hub RPM/Speed
2450
2450
2450
2450
Road Speed - KPH*
350
350
350
350
Road Speed - MPH*
220
220
220
220
POWER REQUIREMENTS:
2WD Application
100, 110, 230 or 240V AC,
Single phase,
1kW maximum
COOLING WATER
REQUIREMENTS:
low pressure, 20°C (68°F).
2.6 Litres per second,
(40 US gpm) max
CONTACT DETAILS:
[email protected]
www.dynapack.com
Note: Specifications are subject to change without notice.
Note* Road Speed (KPH and MPH is dependant on final drive ratio and tyre size)
4WD Application
4WD Model Range
Model
DAQ22
DAQ32
DAQ33
DAQ42
DAQ43
HP Capacity
804
1544
1850
1743
2158
kW Capacity
600
1152
1380
1300
1610
lb/ft Torque Capacity
2950
3687
4424
4425
5162
Nm Torque Capacity
4000
6000
6000
600
7000
Hub RPM/Speed
2450
2450
2450
2450
2450
Road Speed - KPH*
350
350
350
350
350
Road Speed - MPH*
220
220
220
220
220
Model
DAQ44
DAQ52
DAQ53
DAQ54
DAQ55
HP Capacity
2466
2000
2317
2625
2779
kW Capacity
1840
1497
1728
1958
2073
lb/ft Torque Capacity
5900
4790
5531
6269
6638
Nm Torque Capacity
8000
6000
7500
8500
9000
Hub RPM/Speed
2450
2450
2450
2450
2450
Road Speed - KPH*
350
350
350
350
350
Road Speed - MPH*
220
220
220
220
220
Note: Specifications are subject to change without notice.
Note* Road Speed (KPH and MPH is dependant on final drive ratio and tyre size)
Taking vehicle
diagnosis a quantum
leap forward
Dynapack Head Office
International Dynamometers
Ltd
58 Victoria Street Alicetown
Lower Hutt 5010
New Zealand
Tel: 64 4 587 0484
Fax: 64 4 587 0485
Dynapack USA
1175 Shaw Avenue
Suite 104-368
Clovis, CA 93612
USA
Tel: +1 559 292 3800
Dynapack Greece
C/O Dimitris Ghelis
11 Chalder Street Marrickville
Sydney NSW 2204
Australia
Tel: 61 2 9557 4000
Fax: 61 2 9557 4366
Dynapack Australia
PO Box 6765GCMC
9726 Queensland Australia
Tel: 61 419 798510
Dynapack Taiwan
Power-Friend International
No1-3 Zhulin Rd
Linkao District
New Taipei City, 24443
Tel: +886 2 8601 1369
Fax: + 886 2 8601 1499
Dynapack Russia
Moscow, Russia
Tel: +7 903 153 83 33
Dynapack UK
Advanced Motorsport & Engineering
BLDG 5, The Old Depot, Harmans Way
Weedon, Northants, NN7 4PS
United Kingdom
Tel: +44 (1327) 857 577
Dynapack South
East Asia
Mommentum Djaja
Brawijaya VI No.
1 Kebayoran Baru
Jakarta 12160
Indonesia
Tel: 6221 7279 6445,
6221 7279 6481
Fax: 6221 739 6628
Dynapack Thailand
81/2 Moo 6Naklua,
Banglamung
Chonburi 20150
Thailand
Tel: 66 86 344 9032
Tel: 66 86 397 4918
Dynapack China
Suzhou UIGlory Corp Ltd
Room 201, Building No. 5,
Zhuyuan Road, SND,
Suzhou, China 215011
Toll Free: 400 680 7990
Tel: +86 512 6802 8850
Dynapack Hong Kong
Turn Three Ltd
Flat 12, G/F, Transport City Building, 1-7 Shing Wan Road Sha Tin,
New Territories
Hong Kong
Tel: +852 2727 0082
Inside YMS, Pit 100 Ota,
162-2 Nishiyajima,
Ota-shi,
Gunma-ken,
Japan 373-0823
P: + 81 276 56 4038
F: +81 276 56 4078
www.dynapack.com