Surface Mining and Reclamation Application

Butte County
Mining Permit &
Reclamation Plan
Application Packet
Butte County Department of Development Services
TIM SNELLINGS, DIRECTOR | PETE CALARCO, ASSISTANT DIRECTOR
7 County Center Drive
Oroville, CA 95965
(530) 538-7601 Telephone
(530) 538-7785 Facsimile
TABLE OF CONTENTS
1. INTRODUCTION …….……..………………….…………….……..…….… 3
2. APPLICATION PACKET CHECKLIST…………………….……..……... 4
3. BUTTE COUNTY MINING PERMIT APPLICATION ….…..…..…..….. 6
4. AGENT AUTHORIZATION FORM…………………………….……….… 9
5. NORTHEAST INFORMATION CENTER FORM……………….…….... 10
6. REQUIREMENTS FOR PROJECT REPORT ….…..……………..….…. 11
7. REQUIREMENTS FOR EXHIBITS….…………..……………..…..….…. 14
8. STEPS IN PERMIT PROCESSING ….…..….……………….…….….….. 17
_____________________________________________________________
Page 2
Butte County Mining Permit & Reclamation Plan Application Packet
Introduction to the Butte County Mining Permit Application
A mining permit is a complex undertaking that involves a variety of professional disciplines. The
Department of Development Services recommends that you discuss your proposal with a planner
prior to submittal and that you seek professional representation with a firm (or firms) with a
background in Mine Reclamation, Biology, Revegetation, Botany, Engineering, Grading, Geology,
Seismic and Landslide Hazards, Erosion and Sediment Control, Drainage, Noise Impacts,
Hazardous Materials Handling, Traffic Impacts, Aesthetic Impacts and other Environmental
Impacts pursuant to the California Environmental Quality Act (CEQA).
The Butte County Mining Permit Application encompasses two permit applications:
1) A Use Permit that allows for the proposed surface mining activity, and
2) A Reclamation Plan that describes how the mine will be reclaimed into a useful land use after
mining is completed in a given phase, area, or on the entire project site.
Mining Permit applications will be considered for completeness through a County interdepartmental review, by the Butte County Surface Aggregate Operation Committee, and by the
Office of Mine Reclamation, Department of Conservation. Proposals are subject to the California
Environmental Quality Act; therefore, a determination will be made as to whether a Mitigated
Negative Declaration or Environmental Impact Report will be prepared after the application is
considered complete.
When preparing the appropriate environmental document, Butte County staff will assess the land
use compatibility of mining projects with their surrounding areas and neighbors, such as: the
influence of noise, air pollution, dust and lighting from the mine, the influence of truck traffic to
and from the mine on circulation patterns, intersections and County roads, the visibility of the
mine during operation from surrounding properties, the mine’s influence upon off-site drainage
patterns and floodplains, and how potential blasting operations will influence surrounding
neighbors. This list is not meant to be exhaustive and other considerations may arise during the
review process. Additional environmental studies may be required to determine the level of
significance of impacts generated by the proposal.
Mining in Butte County is regulated under Chapter 13 of the Butte County Code and under the
California Surface Mining and Reclamation Act (SMARA). County Code and State Law indicate
that a Mining Permit and Reclamation Plan are required for the extraction of minerals for
commercial purposes and the removal of overburden in total amounts equal to more than one
thousand (1,000) cubic yards or more than 1-acre. Some exceptions apply under the law, and you
should review any proposed exception with a Butte County planner prior to any mining activity.
SMARA also requires the posting of Financial Assurances in an amount necessary to pay for
reclamation of the mine in accordance with the Reclamation Plan. This security can be submitted
in the form of a bond, certificate of deposit or other approved instrument.
_____________________________________________________________
Page 3
Butte County Mining Permit & Reclamation Plan Application Packet
APPLICATION PACKET CHECKLIST
Prior to preparing this application, the applicant should discuss the application requirements with
Department of Development Services, Public Works and Environmental Health staff. Please note
that acceptance of your application is not an indication of approval. Application packets with
missing components cannot be accepted.
Items required for Application Submittal
Applicant Planner
1.

A completed, signed Butte County Mining Permit Application
2.

If the application is signed by an agent for the owner, an agent authorization
form must be submitted.
Payment of the currently required Application Fees and Deposits. Make
checks payable to “Butte County Treasurer”. Public Fee Schedule is
available under “Fees” at: http://www.buttecounty.net/dds/Planning/
Additional fees for publication notices will be required prior to issuance of
the mining permit. Application fees are non-refundable. __________
Applicant’s Initials
4.

Evidence all owners of a possessory interest in the land to be mined have been
notified of the end land use
If the applicant is not the property owner, a copy of the lease agreement for
the proposed site
A creation document for the project parcel and evidence of current property
ownership
Copy of the approved financial assurance cost estimate. For guidelines visit,
http://www.consrv.ca.gov/OMR/financial_assurances/ .
If applicable, list numbers for associated or previous Butte County Planning
projects: ______________________________________________
Consult the Cortese list of hazardous materials sites compiled pursuant to
Government Code Section 65962.5, and determine whether the project is
located on or near an identified site. California’s hazardous sites are listed
and mapped at: http://www.envirostor.dtsc.ca.gov/public/
The project site is on or near an identified hazardous waste site.
Exhibits
10.
11.
12.
13.
14.
15.

(Detailed requirements listed on page 8)
Detailed Project Report (I)
Thirty-five copies of a topographic pre-mining site plan (II)
Thirty-five copies of the mining site plan (III)
At least three cross-sections of the mined area (IV)
Detailed map of the equipment area during mining operations (V)
Thirty-five copies of a topographic post-reclamation site plan (VI)
_____________________________________________________________
Page 4
Butte County Mining Permit & Reclamation Plan Application Packet
17.

18.

19.

16.
A detailed geologic report (VII)
Digital photos (in printed and digital format) of the project site showing:
access roads, location of proposed uses, panoramic views from surrounding
vantage points, panoramic views of surroundings and uses, particularly
nearby residences. Include a map index showing the points from which the
photos were taken, the approximate area of coverage for each photograph,
and a brief narrative of the features shown.
An aerial photo of the project site and immediate surroundings, recent
enough to depict current conditions, and showing an outline of the site
Other reports or documents
(Describe:_____________________________________________________)
_____________________________________________________________
Page 5
Butte County Mining Permit & Reclamation Plan Application Packet
Butte County Department of Development Services
TIM SNELLINGS, DIRECTOR | PETE CALARCO, ASSISTANT DIRECTOR
7 County Center Drive
Oroville, CA 95965
(530) 538-7601 Telephone
(530) 538-7785 Facsimile
BUTTE COUNTY MINING PERMIT APPLICATION
Project #_________
GENERAL OWNERSHIP/OPERATOR INFORMATION
Mine Name:
California Mine ID# [if one has been assigned]:
-
-
Location of Mine [Include Street Address]:
Section________________ Township________________ Range________________
Assessor’s Parcel Number(s):
Size: ___________Acres
Applicant’s Name:
Mine Operator(s)’ Name:
Telephone Number(s):
E-Mail Address:
Mailing Address:
Property Owner(s)’ Name :
Telephone Number:
E-Mail:
Mailing Address:
Mineral Rights Owner(s)’ Name:
Telephone Number:
E-Mail:
Mailing Address:
_____________________________________________________________
Page 6
Butte County Mining Permit & Reclamation Plan Application Packet
GENERAL MINING OPERATION INFORMATION
Type of operation:
Days and hours of operation:
Number of employees:
Number of daily vehicle trips:
Mined Mineral Commodity(ies):
Estimated Annual Production: (tons or yds.3/yr.)
Estimated Total Production: (tons or yds.3/yr.)
Waste off-site: ______________
Mineral_____________ Waste on site: ___________
Topsoil to be retained on-site: _____________
Total Number of Acres to be Disturbed by the Surface Mining Operation: _______________
Total Number of Acres to be Reclaimed: _______________
Maximum Anticipated Depth of Mining: __________Feet at _________Elevation (Mean Sea Level)
Start Date [Indicate Whether Actual Or Proposed]:
Estimated Life of Operation: (phases and total)
Describe the type of mining to be employed [e.g., quarry/truck and shovel operation]:
RECLAMATION ACTIVITIES
Revegetation
Check the revegetation scenario that best describes the project site:
Revegetation, in conformance with CCR Section 3705, will be a part of my approved
reclamation plan.

End use precludes revegetation or the cultivation of disturbed lands.

Revegetation is not consistent with the approved end use.
_____________________________________________________________
Page 7
Butte County Mining Permit & Reclamation Plan Application Packet
Agriculture
Check the relationship to agriculture that best describes the project site:
Mining operation will not be conducted on prime agricultural lands, and the site's end use will
not be agriculture.

Mining operation will be conducted on prime agricultural lands, but the site's end use will not
be agriculture.

Prime agricultural land reclamation - The mining operation will be conducted on prime
agricultural lands, and the site's end use will be agricultural. Thus, I agree to reclaim prime
agricultural lands in conformance with CCR Section 3707. Explain the reclamation
procedures you will use to meet the standard cited above in your reclamation plan.

The mining operation will be conducted on non-prime agricultural lands where the site's end
use will be agriculture. Thus, I agree to reclaim non-prime agricultural lands in conformance
with CCR Section 3708. Explain the reclamation procedures you will use to meet the standard
cited above in your reclamation plan. Note: Performance standard should be based on
productivity [e.g., bushels per acre, tons per acre].

Mining operation will be conducted on non-prime agricultural lands, but the site's end use will
not be agriculture.

Check if the property is subject to a Williamson Act Contract
MONITORING
Pursuant to CCR Section 2773(a), the success of reclamation will be monitored for three years, or
until performance standards are met, provided that, during the last two years, there has been no human
intervention, including, for example, irrigation, fertilization, or weeding. Remedial measures will be
implemented as necessary to achieve the performance standards.
STATEMENT OF RESPONSIBILITIES
I, the undersigned, hereby agree to accept full responsibility for reclamation of all mined lands as
described and submitted herein and in conformance with the applicable requirements of Articles 1
and 9 (commencing with Sections 3500 et seq. and 3700 et seq., respectively) of Chapter 8 of
Division 2 of Title 14 of the California Code of Regulations, the Surface Mining and Reclamation Act
commencing with Section 2710 et seq., and with any modifications requested by the administering
agency as conditions of approval.
Signed this
day of
, 20____
Mine Operator or Operator's Agent ________________________________________________
_____________________________________________________________
Page 8
Butte County Mining Permit & Reclamation Plan Application Packet
AGENT AUTHORIZATION
To Butte County, Department of Development Services:
(
)
Phone Number
Print Name of Agent
Mailing Address
is hereby authorized to process this application on my/our property, identified as Butte County
Assessors Parcel Number(s):
This authorization allows representation for all applications, hearings, appeals, etc. and to sign all
documents necessary for said processing, but not including document (s) relating to record title interest.
Owner(s) of Record (sign and print name)
______________________________________
Print Name
_______________________________________
Print Name
______________________________________
Signature
_______________________________________
Signature
______________________________________
Print Name
_______________________________________
Print Name
______________________________________
Signature
_______________________________________
Signature
______________________________________
Print Name of Applicant (if other than owner)
_______________________________________
Signature of Applicant (if other than owner)
Print Name of California Civil Engineer/Land Surveyor
Mailing Address
( )
Phone Number
Email Address
_____________________________________________________________
Page 9
Butte County Mining Permit & Reclamation Plan Application Packet
Agreement For
Butte County Archaeological Resources Project Review By
The Northeast Information Center (NEIC)
The California Environmental Quality Act (CEQA) is the California State statute that requires the Butte County Department
of Development Services to perform an environmental review on all discretionary land use projects, to identify the
significant environmental impacts of the project and to avoid or mitigate those impacts, if feasible.
Every development project which requires a discretionary governmental approval will require at least some environmental
review pursuant to CEQA, unless an exemption applies. The environmental review required imposes both procedural and
substantive requirements. At a minimum, an initial review of the project and its environmental effects must be conducted.
Depending upon the potential effects, a further and more substantial review may be conducted in the form of an
environmental impact report (EIR). A project may not be approved if feasible alternatives or mitigation measures cannot
substantially lessen the significant environmental effects of the project. At the state level, CEQA requires that public
agencies consider the effects of their actions on historical resources eligible for listing on the California Register of
Historical Resources. “Historical resource” refers to buildings, structures, sites (prehistoric and historic), objects, districts,
and all manner of properties containing material remains of past human life or activity.
The Department of Development Services utilizes the Northeast Information Center (NEIC) of the California Historical
Resources Information System (CHRIS) to identify projects that may have archaeological significance. The CHRIS is a
statewide system for managing information on the full range of historical resources identified in California. This system is
under the authority and direction of the Office of Historic Preservation (OHP), the State Historic Preservation Officer
(SHPO), and the State Historical Resources Commission (SHRC). The Northeast Center of the CHRIS system, located at
California State University, Chico, manages the historical resource records for 11 counties, including Butte County.
The Northeast Information Center will furnish a Record Search to Development Services indicating the
archaeological/historical significance and sensitivity of the applicant’s project area and additionally providing a
recommendation as to whether further archaeological survey is warranted. If further archaeological survey is required, the
application would be considered incomplete until the appropriate archaeological survey is completed and reviewed.
The Department of Development Services will forward applicant’s payment (by check) of $75.00 and relevant project
application information required for the Records Search to NEIC. NEIC will provide the results of the Records Search to
Development Services. Development Services will notify the applicant if further archaeological survey is warranted. The
$75.00 fee does not cover the cost of further archaeological survey work.
If further archaeological survey work is required, Development Services will work with the applicant to see that it is
accomplished, according to set standards, by a qualified archaeologist. The applicant shall bear all costs associated with
further archaeological survey work required to continue processing of the planning project application.
THIS FORM MUST BE ACCOMPANIED BY A COPY OF A 7.5’ TOPO MAP, WITH THE PROJECT AREA
OUTLINED. THIS IS USED DURING THE REVIEW TO RESEARCH CULTURAL SITES.
The undersigned applicant for the project as identified below has read and understood the Butte County Archaeological
Resources Project Review process and agrees to fund the required Record Search to be provided by NEIC.
Attached is a check for $75.00 made payable to the Northeast Information Center for NEIC to perform the Records Search.
Applicant Signature
Date
Applicant PRINTED Name
Check Number
Planner; File Number
_____________________________________________________________
Page 10
Butte County Mining Permit & Reclamation Plan Application Packet
Exhibit Requirements
I. Detailed Project Report
Site Description
1. Describe access to the site
2. Describe the site’s environmental setting, including the following: a general description of the
area’s land use (including the nearest residential development), vegetation, soil, ground water
elevation, surface water characteristics, average annual rainfall, and a list of plants currently on
site that may be suitable for reclamation. Describe any baseline monitoring that has been done
to document present environment.
3. List any sensitive species, sensitive habitats (wetlands, vernal pools, etc.) on site.
4. Describe the visibility of the proposed operation from the surrounding area (considering
highways, residences, commercial development, and recreation areas). Discuss proposed
mitigation (e.g. landscaping, berms, fences, modification of operation, etc.).
5. Describe surface water characteristics of the site (drainage patterns, size of the area that drains
into site, proposed alteration of drainage patterns, etc.). Describe the methods to insure positive
drainage of site and to minimize adverse effects on adjacent property.
6. If site is within a recognized floodway, 100-year floodplain, or an area subject to flashflooding,
then describe methods to protect project from flood damage and to insure that the project will not
intensify flooding effects on surrounding property.
7. If site is within or upstream of a groundwater recharge area, then discuss potential for project to
increase siltation of recharge area or to otherwise decrease its absorptive qualities. Describe
methods to protect recharge from these effects.
8. If the operation will introduce any to toxic substance, contaminate, or otherwise degrade the
quality of stream run-off from the site, then describe methods to minimize those effects.
9. If there are any stream gauging stations within the site, then describe methods to preserve or
relocate the stations.
10. Describe groundwater, subsurface geology, permeability, fault barriers, structural constrictions
in the basins, quantity, quality, and direction of flow. If groundwater is pumped by wells for use
on, around, or downstream of the site, then describe any adverse effects that may occur to the
quantity, quality, or depth of groundwater and describe methods to minimize these effects.
11. Describe the various soils on the site, including their physical and chemical characteristics,
average thickness, erodibility, and land use capability.
12. Describe the types of vegetation that grow on and around the site using both common and
scientific names. List Federal and/or State-designated Rare, Threatened or Endangered Species
on or near the site, and discuss proposed mitigation.
13. List any wildlife species occurring on and around the site using both common and scientific
names. List Federal- and/or State-designated Rare, Threatened, or Endangered Species on or
near the site. Discuss proposed mitigation in compliance with CCR Section 3703.
_____________________________________________________________
Page 11
Butte County Mining Permit & Reclamation Plan Application Packet
Mining Operations
1. Briefly describe the proposed mining operation including removal of vegetation and overburden,
how the mineral commodity will be extracted (open pit, dredging, drill and blast, etc.), the
equipment that will be used, and any proposed phasing of the operation (including dates).
2. Describe the overall design slope, including benches, distance between benches, and maximum
slope angle of walls. Provide verification by an Engineering Geologist or Soils Engineer that
finished cut slopes will be stable under static and dynamic conditions.
3. Provide estimates of the volume and weight per year in cubic yards and tons and total
commodity to be produced during the life of the permit, including waste material.
4. Describe any planned on-site (or adjacent) ore processing methods such as: dry screening,
flotation, amalgamation, wet screening, crushing/grinding, washing, mechanical separation,
smelting, leaching, or batch plant, and explain the disposal method for the tailings or waste from
processing. (Note: If cyanide is used for on-site processing, PRC Section 21151.7 requires the
preparation of an environmental impact report under the California Environmental Quality Act.)
5. State the maximum and average quantity of water used in gallons per minute and acre-feet per
year. Indicate the proposed or existing sources of water such as reservoirs, wells, ponds,
diversions, municipal water supply, etc. and the method of its conveyance to this property
6. Estimate the amount of wastewater disposed of in gallons per minute and acre-feet per year.
Indicate the volume of excess processing water, mine drainage, storm runoff from disturbed or
utilized areas and any other water which will be handled on the site. Describe anticipated or
possible contaminants including processing chemicals, detergents, acid drainage, turbid (muddy)
water, fuel oil or gasoline, and runoff water which may contain fertilizer or other soil
amendments and methods for their disposal.
7. Describe the type(s) of waste to be produced (e.g., topsoil, overburden, tailings, and sediment)
List the amount of each type of waste to be produced during the life of the mine and the disposal
method for each type of waste, whether to be retained on or off-site.
8. If any imported materials, such as domestic garbage, chemicals, oil or other material will be
disposed of on the project site, then describe what types, in what expected amounts, and the
method of their disposal.
9. Describe methods to prevent erosion and/or sedimentation of adjacent property due to waters
discharged from the site. Also, describe methods to protect stockpiles of mined materials and
topsoil from water and wind erosion.
10. Describe procedures for storage and detonation of explosives, including notification of
authorities, and methods to reduce effects on offsite structures and residents.
11. List and describe the number of daily truck trips (include truck size), haul routes and any known
destinations.
Reclamation Activities
1. Describe the proposed use of the site once mining ceases and reclamation is completed,
considering the site’s zoning and General Plan land use designation.
2. Provide a time schedule for the reclamation of each area disturbed by mining. If applicable,
indicate dates for each reclamation phase, including concurrent reclamation. Explain any time
gaps between finishing a mining phase and beginning land reclamation.
3. Describe how the proposed reclamation of the mine site will affect public health and safety,
_____________________________________________________________
Page 12
Butte County Mining Permit & Reclamation Plan Application Packet
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
giving consideration to the degree and type of existing and probable future public exposure to
the site. Describe future measures to ensure public safety (fences, signs, hazard removal, etc.).
Describe in detail what the mined site will look like after it has been reclaimed.
Describe the method (in conformance with CCR SECTION 3711) of removal, storage, and
replacement of topsoil; the mean thickness of topsoil or fines on the site after reclamation;
testing to determine whether soil or mine wastes need to be modified to encourage plant growth.
If the final reclaimed fill slope ratio will be greater than 2:1, attach a site-specific geologic and
engineering analysis that demonstrates that the proposed final slope will have a minimum slopestability factor of safety that is suitable for the proposed end use, and that the proposed final
slopes can be successfully revegetated. Also provide a geologic cross section of cut and fill
slopes at locations of maximum slope height.
Discuss how cut and fill slopes, waste piles, and tailings will be stabilized to prevent landslides,
earth flows, rock falls, and erosion (revegetation, benching, scaling, slope reduction, etc.).
Describe how pit areas or excavations will be reclaimed (backfilled, regraded, topsoiled,
revegetated, etc.) in conformance with CCR SECTION 3704.
Describe how ponds, tailing, and/or mine wastes will be reclaimed (regraded, dewatered, capped,
revegetated, removed, etc.). If any dams or embankments are to remain after reclamation,
describe type of dam, construction material, permeability, foundation characteristics, storage
volume and design criteria (including design criteria for seismic hazards), and prepare a cross
section through dams or embankments showing design characteristics.
Describe methods and timing for removal, disposal or utilization of residual equipment,
structures, refuse, etc. in conformance with CCR SECTION 3709. Explain the reclamation
procedures for closure of surface openings in accordance with CCR SECTION 3712.
Describe the revegetation plan, including:
a. A list of at least four native species that occur on site or in the vicinity of the project
that will be used for revegetation, unless non-native species such as forage grasses or
ornamentals will be used.
b. Proposed Revegetation Mix, including quantified vegetative cover, density, and
number of species of the reclaimed mined lands as compared to local areas of
naturally occurring vegetation or pre-mining conditions (baseline).
c. Explain the method, timing and rate of planting (including fertilizers and soil
preparation) and the irrigation system.
Explain the reclamation procedures for stream protection, including surface and groundwater, in
accordance with CCR SECTION 3710. If mining operation is conducted in a stream or other
waterway, attach cross sections identifying baseline streambed elevations. (Note - Changes in
channel elevations and bank erosion shall be evaluated annually. Extraction quantities and
annual cross sections should be submitted with the annual report required by PRC Section 2207.)
Describe maintenance program to ensure that revegetation is successful, and that public safety
measures, water quality erosion control treatments, etc. are maintained. Indicate who will be
responsible for carrying out the maintenance and monitoring program.
For reclamation to habitat, include information on the type of habitat proposed and the specific
measures that will be implemented to create the habitat.
Describe assurance mechanism(s) to guarantee reclamation of the site (e.g., bonding, letter of
credit).
_____________________________________________________________
Page 13
Butte County Mining Permit & Reclamation Plan Application Packet
The Following Apply to all Exhibit Maps:
1. Must be clear and legible
2. Must be drawn to standard engineering scale (e.g., 1" = 50')
3. Must indicate scale and include a north arrow oriented to the top of the sheet
4. Must indicate the name, business address and phone number of the applicant and the
person who prepared the map and the date prepared
5. Must indicate Assessor Parcel Number(s); street address (if available); and Township,
Range and Section
6. Must include a vicinity map indicating the location of the land in relation to the nearest
major roads and/or significant topographic features in the region
7. Provide thirty-five (35) copies on uniform size sheets no less than 11”x17” and no
greater than 24" X 36", folded to 8 ½" x 11".
8. Provide one reduced 11”x17” copy.
9. Provide one digital copy.
II. Requirements for the Detailed Topographic Site Plan Prior to Mining Operations
Applicant Planner
a.
b.

Existing and proposed zoning and General Plan land use designation
Dimensioned locations of existing public or private improvements on the property (including,
but not limited to, buildings, driveways, roads, railroads, parking areas, drill holes, water wells,
septic tanks, sewer lines, leach fields, utilities, signage, storm drainage systems and lighting.)
d.

Indicate at least one route from the property to a publicly-maintained road.
e.

Location, width and direction of flow of all water features including, but not limited to, natural
and human-made drainage courses, irrigation canals, ponds, creeks, sloughs
Maximum groundwater elevations
g.

Elevation contours, at an appropriate vertical scale and topographic features including, but not
limited to, buttes and slopes, or rock out-croppings
h.

Any existing faults or fractures and geologic hazards
i.

Approximate location of all FEMA identified 100-year floodplain areas
j.

Existing vegetation, such as oak trees greater than 5” in diameter and agricultural crops
Distances between the property lines and any significant natural or constructed features of the
property, such as streets, access roads, streams, rock outcroppings, major tree stands, storm
drains, bodies of water, railroads
Approximate location of all buildings, wells, septic tanks and leach fields within 300 feet, on
adjacent properties
m.

Property lines, lot dimensions, acreage and any applicable easements of record or proposed
Any areas of previously reclaimed land
_____________________________________________________________
Page 14
Butte County Mining Permit & Reclamation Plan Application Packet
III. Requirements for the Detailed Mining Site Plan
Applicant Planner
a.
b.

Property lines, lot dimensions and any applicable easements of record or proposed
c.

Dimensioned locations and boundaries of areas to be mined (labeled by phase), waste dumps,
stockpiles, tailing ponds, retarding basins, and settling ponds, erosion control facilities, settling
ponds, temporary stream diversions
d.

Volume of topsoil stockpiles, crest, toe, and volume of overburden stockpiles, crest and toe of
pit(s)
e.

Depict separate mining phases where applicable, including phasing dates and volumes to be
mined.
Identify all surface openings.
h.

Acreage of area to be mined and maximum depth of excavation
i.

Elevation contours, at an appropriate vertical scale showing the maximum anticipated depth
Location and details of facilities to control on- and off-site storm runoff, erosion, and
sedimentation (such as water courses, culverts, drainpipes, settling ponds, retarding basins,
ditches, and dikes). Include data on amount of runoff and gradients of facilities.
If applicable, exact legal boundaries of area(s) leased by the applicant
Proposed access roads, setbacks, location of processing facilities and equipment storage areas
IV. Cross sections
At least three cross sections for each stage: pre-mining and post-mining. The elevation cross sections
should show the progression of stripping, excavating and reclaiming through cuts, fills, and drainages.
Cross sections should include phase designations and should show the extent of overburden, mineral
deposits, groundwater level, and details of the working face of the operation.
V. Map of Equipment Area
Location and description of operating equipment and structures, including:
•
Proposed and existing buildings (offices, break
rooms, etc.)
•
Parking areas
•
Processing plant equipment
•
Lighting
•
Truck wash area
•
Signs
•
Fuel and material storage areas
•
Scale station
•
Sanitary facilities, including septic system and
leach lines
•
Stockpile areas for topsoil
•
Areas to be devoted for test-plots to test the
performance of plants used in reclamation
while mining is taking place.
•
Stockpile areas for mined material
•
Wash/settling ponds
_____________________________________________________________
Page 15
Butte County Mining Permit & Reclamation Plan Application Packet
VI. Requirements Shown on the Post-Reclamation Site Plan
Applicant Planner
a.
b.

Property lines, lot dimensions and any applicable easements of record or proposed
c.

Boundaries of areas to be reclaimed, including acreage
d.

Post-reclamation drainage, including critical areas within or near the project area such as lakes,
streams, or wetlands. Show direction of flows with arrows. Erosion and sediment control
structures or treatment such as water bars, berms, siltation ponds, diversions, etc.
e.

Reclaimed ground surface elevation contours, at an appropriate vertical scale
g.

All surface openings closed through reclamation
Buildings, structures and equipment to be either dismantled and removed from the site or to
remain on site and be consistent with the end use
Illustrate the ultimate physical condition of the site and specify proposed uses or potential uses
of the land, as reclaimed.
Indicate post-mining safety features (e.g. fences, gates, signs).
If applicable, exact legal boundaries of area(s) leased by the applicant
Revegetation plan including names of plant species, size, area and spacing of plants
VII. Requirements for Geologic Report
1. Describe the geology of the area surrounding the mine site, considering principal rock formations,
overburden materials, principal ore and gangue minerals. Describe the geometric interrelationships
of earth materials, including estimates of thickness, aerial extent, volume and tonnage of materials to
be mined.
2. Describe the geologic conditions which could adversely affect the project, considering earthquake
faults, Special Studies Zones, groundshaking, landslides, mudflows, liquefaction hazards,
differential settlement, hydroconsolidation, collapsible or expansive soils, wind erosion, water
erosion, sedimentation, and inundation due to earthquake-induced dam failure. Discuss proposed
mitigation.
_____________________________________________________________
Page 16
Butte County Mining Permit & Reclamation Plan Application Packet
Surface Mining Permit Application Process
Pre-application Meeting with Butte County Agencies
Submittal of Application
Review by Surface Mining Aggregate Operations Committee
Review by Butte County Inter-Departmental Committee
Review by Office of Mine Reclamation, Department of Conservation
Comprehensive Project Review / Initial Study
Negative Declaration or EIR Required
Preparation of Public Hearing Staff Report
Public Hearing at Planning Commission
(Appeal)
Board of Supervisors
_____________________________________________________________
Page 17
Butte County Mining Permit & Reclamation Plan Application Packet

Download Report

Surface Mining and Reclamation Application

Paperzz.com

Your Paperzz