EN – PROMETHEUS
FIND YOUR OWN BEAM LIGHT SOLUTION
WARNING: READ THE INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP IT WITH THE PRODUCT.
3.
A LED red located near the USB port on the
charging base indicates that the torch is charging.
4.
When the charging is complete, the green LED
switches on. Disconnect the USB cable first from the
network adapter (or from your computer) and then
from the charging base.
TECHNICAL FEATURES: refer to the table
WARNINGS
Remove the batteries if the torch will not be used for
long periods or during transports.
Make sure that the torch is turned OFF correctly after
every use and before storing.
SWITCH SPORT MODEL
EXTREME AND ICE MODELS
If you plan extended period of disuse, we recommend you
to recharge the battery every 4 months.
To switch on the torch simply screw the frontal part on
with respect to the torch body (see fig.1).
Follow the same procedure above, but be sure to turn ON
the torch after pluging in the micro USB, to start the charging process. If you don’t switch the torch ON, the LED indicator will remain green with battery uncharged.
If water leaks occur or in the event of a malfunction,
contact the iWave Ocean Dealer where you purchased the
product.
SWITCH EXTREME AND ICE MODELS
Be sure the frontal head is completed screwed and turn the
main switch (bottom part of the body).
The torch can operate in two modes: 100% and 50%. It is
possible to switch from mode 100% to mode 50% just
switching on and off more than 1 time.
WARNING: NEVER DIRECT THE BEAM LIGHT DIRECTLY
INTO YOUR EYES.
RECHEARGEABLE BATTERIES
The torch have a “Low battery alert” system. When the
battery voltage became too low the electronic control keeps
the level of the LED current at minimum level and the light
starts to blink. This is the signal to charge the battery.
The burn-time of the battery is reported in the following table. Burn-time can be influenced by different factors,
such as: operating temperature, period for which the torch
was not used, number of charging and discharging cycles,
storage method of the product.
RECHARGING THE BATTERY
WARNING: DO NOT CHARGE THE BATTERY NEAR FLAMMABLE ITEMS AND / OR PRODUCTS.
1.
Unscrew the frontal part from the torch body (See
fig. 2)
2.
Plug the Micro USB connector into the port on the
charging base (Fig.3) and connect it to the network
adapter (5V recommended) or to your computer
(500mA).
WARNING: TO PREVENT DAMAGE TO THE TORCH,
THINGS OR PEOPLE, IWAVE DESIGN RECOMMENDS YOU
NEVER LEAVE THE TORCH CONNECTED TO THE BATTERY CHARGER FOR MORE THEN 3-5 HOURS FROM
THE EXPECTED TIME FOR A FULL CHARGE.
REPLACING THE RECHARGEABLE BATTERY (FIG. 4)
WARNINGS: DON’T USE OTHER BATTERY WHICH IS NOT
DESIGNED FOR THE PRODUCT AND/OR IF IT IS SERIOUSLY IMPACTED OR DAMAGED. ANY REPLACEMENT BATTERY USED IN THIS PRODUCT MUST BE ORIGINAL IWAVE
OCEAN. ORIGINAL BATTERY INCLUDE OVER / UNDER
VOLTAGE PROTECTION, OVER CURRENT PROTECTION
AND SHORT CIRCUIT PROTECTION. THE USE OF NOT
ORIGINAL BATTERIES CAN CAUSE SERIOUS DAMAGES TO
THE PRODUCT AND TO THE USERS.
1.
Unscrew frontal part of the torch
2.
Unscrew the charging (see fig.4)
3.
Insert the new rechargeable battery into the torch
body.
WARNING: MAKE SURE THE BATTERY IS INSERTED FOLLOWING THE CORRECT POLARITY (FIG.4)
4.
PERIODICAL MAINTENANCE
Rinse the outside of the torch in fresh water after every
dive, without disassembling it.
Store the torch in fresh and dry places, never leave the
product in places where the temperature can reach 50°
C.
WARNING: TO PREVENT ANY POSSIBLE OCCURENCE
OF GALVANIC CORROSION, DO NOT USE AND / OR
STORE THE TORCH IN CONTACT WITH METAL OBJECTS.
Periodically check the integrity of the O-rings.
WARRENTY
This product carries a two years warranty against manufacturing or material defects. All warranty claims must
be returned with date proof-of-purchase to an authorized iWave Ocean dealer. Visit www.iwaveocean.com
for the dealer nearest to you.
Water leaks are not covered by warranty. 100% iWave
Ocean products are tested in pressure at 20 bar before
leaving the Factory. This special test is done to verify the
product in extreme conditions before deliver it to the customer.
Fully screw down the charging cap and screw the
frontal part on.
WARNING: BE EXTREMELY CAREFUL WHEN SCREWING
THE FRONTAL PART ON THE TORCH BODY TO AVOID TO
DAMAGE THE O-RINGS.
For any further information please contact
[email protected]
Fig. 1
Prometheus Technical features
Super Spot
Light source
Color temperature
Light Beam angle
Fig. 2
USB port
LED
Fig. 3
Fig. 4
Lumen [Tj 25°C] 100%, 50%
Lumen [Tj 85°C] 100%, 50%
Lux at 1 mt
Burn time [100%; 50%]
Switch
Low voltage protection
Colors available
Operating mode
Working temperature
Battery
Charging system
Battery charging cycles
Prometheus SPORT
Dimensions: diameter [mm]
Weight (out / in water) [gr]
Prometheus EXTREME
Dimensions: diameter [mm]
Weight (out / in water) [gr]
Prometheus ICE
Dimensions: diameter [mm]
Weight (out / in water) [gr]
6° central spot;
15° secondary
emitting angle
1145
1010
24000
3 h; 6 h
Super Spot
54 x 150
335/ 150
Super Spot
54 x 158
335/ 150
Spot
Wide
10W LED
6800 K
7° central spot;
11° central spot;
37° secondary
44° secondary
emitting angle
emitting angle
1145
1400
1010
1250
16500
5300
3 h; 6 h
1,5 h; 3 h
Mechanic
Yes, light blinking system
Black, Red and Blue
2 sequential modes, 100% and 50%
-10°C to 60°C
Li Ion 3,7 V 5000 mAh with protection
By mini-USB (5V power supply needed)
500
Spot
Wide
45 x 150
45 x 140
330/150
300/140
Spot
Wide
45 x 158
45 x 148
330/150
300/140
Spot
45 x 158
300 / 120
Super Wide
120°
1400
1250
130
1,5 h; 3 h
Super Wide
45 x 127
275/135
Super Wide
45 x 135
275/135