REPLACEMENT PARTS LISTS
IDENT. PART
NO.
NO.
1
3045-00
2
1039-02
3
1064-30
80250400
4
1101-20
5
8
9
10
3043-20
3052-00
2570-21
1023-10
1034-00
1247-00
1008-05
1035-03
3134-02
11
3135-21
12
9704-00
6
7
DESCRIPTION
Scale Plate
SST - 6" dia.
Scale Pan
6" dia. x 3/4"
Cross
Scoop, SST
12" x 6
2-3/4" deep
Scoop,
Polypropylene
12" x 6" x 2-3/4" deep
Specimen Pan
Cover
Cross
Balance Cup
Friction Plate
Friction Plate w/Tab
Bearing
Bearing Cover
500g Poise
Assembly
100g Poise
Assembly
225g Tare
REQD
1
1
MODELS
750-S0
750-SW
760-00
710-00
710-T0
1
1
720-S0
1
730-00
1
1
1
1
3
1
4
4
1
730-00
1
All
1
760-00
710-T0
LIMITED WARRANTY
Ohaus products are warranted against defects in, materials and workmanship
from the date of delivery through the duration of the warranty period. During
the warranty period Ohaus will repair, or, at its option, replace any
component(s) that proves to be defective at no charge, provided that the
product is returned, freight prepaid, to Ohaus.
Triple Beam
Balance
This warranty does not apply if the product has been damaged by accident or
misuse, exposed to radioactive or corrosive materials, has foreign material
penetrating to the inside of the product or as a resuft of service or modification
by other than Ohaus. In lieu of a properly returned warranty registration card,
the warranty period shall begin on the date of shipment to the authorized
dealer. No other express or implied warranty is given by Ohaus Corporation.
Ohaus Corporation shall not be liable for any consequential damages.
As warranty legislation differs from state to state and country to country,
please contact Ohaus or your local Ohaus dealer for further details.
All
All
All
All
All
Instuction Manual
Please read this manual before you use your
Ohaus Triple Beam Balance.
Accessories
183-00
703-00
703-S0
706-00
707-00
Specific Gravity Rod and Clamp
Footed Polypropylene Scoop, 12" x 6" x 2-3/4" and Counterweight
Footed Stainless Steel Scoop,12" x 6" x 2-3/4" and Counterweight
Vinyl Dust Cover
Metric Attachment Weight Set: two 1000g, one 500g
1 / 2 / 3 / 4 / 5
11
METRIC MODEL
METRICA MODELOS
10
6
30
0
8
0
100
1
2
40
50
200
3
4
60
300
5
6
70
80
400
7
90
100 g
0
500 g
8
9
10 g
7
*3258-00*
9
NOTE: Item 12 not shown on illustration is
loacated at rear of balance.
P/N 3258-00 A © Ohaus Corporation 2005, all rights reserved / todos los
derechos reservados.
Printed in Poland / Impreso en Polonia
99 Washington Street
Melrose, MA 02176
Phone 781-665-1400
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com
Unpacking:
Carefully remove the balance and the separate poise (sliding weight) from the
protective carton. You will find a slit rubber washer lodged underneath the
platform, and one rubber washer located above the pointer. The washers are to
be removed from the scale.
Attachment weights:
Total capacity is either 2610 grams or 5 pounds, 2 ounces when attachment
weights are suspended from the pivots (14). Without the weights, the capacity is
either 610 grams or 1 pound, 2 ounces.
Solids - (denser than water): To determine specific gravity of solids denser than
water, the specimen should be first weighed in air and then weighed immersed in
water.
Weight in air
Weight in air minus weight in water
Solids - (less dense than water): To determine the specific gravity of solids less
dense than water, it is necessary to attach a sinker and then make the following
weighings:
a. Weight of body in air.
b. Combined weight of body in air plus sinker in water.
c. Weight of both body and sinker in water.
a
b-c
Set-up:
After placing the balance on a smooth, flat surface, slide the separate poise up
into the slot on the back of the center beam. Tilt poise over into place on the
beam. With all poises in zero position, the pointer should be near zero. On
applicable models, the tare poise (13) shall be at the extreme left of its bar.
Formulas:
Use of the tare:
Certain models are equipped with a patented tare poise (13). The poise will
counterbalance empty containers no heavier than 225 grams or 8 ounces, by
sliding it to the approximate balance, then rotating in either direction for precise
positioning. Net weight of the contents of the container may then be read directly
in the usual manner.
Zeroing:
Features:
For exact zero, adjust the knurled knob which is located at the left end of the
beam. It is advisable to check the zero adjustment periodically.
• A low cost, maintenance-free balance which provides all the convenience of a
top loader, yet retains the ruggedness needed for a wide range of lab work.
• Tiered beam visibility and zero adjust combine to give high speed performance
and reduce error.
Care and maintenance:
Weighing:
Place the specimen on the center of the platform and proceed as follows:
1. Starting with the largest capacity beam (500 g), move the 500 g poise to the
right to the first notch which causes the pointer to drop, then, move it back one
notch, causing the pointer to rise.
2. Repeat procedure with the 100 g poise.
3. Slide the 10 g poise to the position which brings the pointer to rest at zero.
The weight of the specimen is the sum of the values of all poise positions, read
directly from the graduated beams.
Keep balance clean at all times. In general, most foreign matter may be easily
removed by an air syringe, but a piece of adhesive-backed tape pressed against
the magnet faces will keep them free from dirt. Never apply lubricants to knives
or bearings, nor allow foreign matter to accumulate.
Specific gravity determination:
The Model 183 Clamp and Rod Support is an accessory for elevating the
balance for suspending specimens in water. The rod is inserted into the 1/2 inch
(12.7 mm) recess on the underside of the
base. By means of a fine wire or thread,
the specimen is attached to the check
pin which connects the check rod
assembly to the platform loop under the
base.
• Magnetic damping speeds up weighing by causing the beam to come to rest
quickly without affecting sensitivity or accuracy. It operates on the principle of
a permanent magnetic field resisting the motion of a non-magnetic, aluminum
damper vane attached to the beam.
The pole faces of the damping magnets are positioned on both sides of the
damper vane. Damping force is proportional to vane velocity and reduces to zero
when the beam stops, thereby turning itself off.
The system is permanent, self-regulating, maintenance-free, frictionless and
effective at all loads.
• Tare beam and poise (13) (on specific models) make repetitive weighings and
chemical formulations easy by eliminating container weight from calculations.
• Attachment weights store conveniently in the base when not in use.
Specifications
Capacity
w/attachment weights
w/o attachment weights
Readability
Calibrations
Front Beam
Center Beam
Rear Beam
700
Metric
Series
2610g
610g
0.lg
10g x 0.1g
500g x 100g
100g x 10g