SCENARIOS S2S MANUAL
SCENARIOS EXECUTIVE
SCENARIOS S2S MANUAL SCENARIOS EXECUTIVE
L E G S + PA N E L
1
2
a.
Cap Screw
M6 x 8mm
Allen Key
5mm
x2
Side view - Slot in end leg from side of the panel,
attach connection plate at the side of the endleg.
b.
Self Tap
Screw
c.
x6
Bottom view - Attach end leg into panel, fix self tap
screws by following a to c.
3
Attach the removable cover to close the panel.
4
Complete look for panel leg.
LEG + CABINET
1
2
a.
b.
x2
M6 x 8mm
Cap Screw
Side view - Slot in end leg from side of the cabinet,
attach connection plate at the side of the endleg.
c.
Self Tap
Screw
x6
Bottom view - Attach end leg into cabinet,
fix self tap screws by following a to c.
1
SCENARIOS S2S MANUAL SCENARIOS EXECUTIVE
LEG + CABINET
3
Attach the removable cover to close the panel.
4
Complete look for cabinet leg.
FRAME
1
x-beam - Mount x-beam to the end leg.
2
x-beam - Mount x-beam to the another end leg.
3
4
a.
x-beam - Complete look for x-beam
b.
Hexagon rod - Slot in a.hexagon outside to the
middle top of end leg, b. slot in hexagon stopper for
both end legs
2
SCENARIOS S2S MANUAL SCENARIOS EXECUTIVE
FRAME
6
5
Hexagon rod - Slot in hexagon inside to hexagon
outside with the same distance for another end leg.
Top view of hexagon rod
Hexagon rod - Hexagon inside should be stop at
hexagon stopper for both end leg.
7
Hexagon rod - Slot in hexagon inside to hexagon
outside with the same distance for another end leg.
8
Complete look for hexagon rod.
CABLE MANAGEMENT
1
Hexagon rod - Hook cable tray on x-beam.
2
Complete look for cable tray.
3
SCENARIOS S2S MANUAL SCENARIOS EXECUTIVE
WORKTOP
1
2
JCBC Screw
x8
M8 x 16mm
Allen Key
5mm
Side view - Attach worktop with JCBC screws from
bottom of top support for both end legs.
Place worktop on frame.
FIXING
1
2
Allen Key
2mm
Allen Key
4mm
Tighten x-beam with set screws for both side of top
supports.
Tighten hexagon stoppers on both side.
4
SCENARIOS S2S MANUAL SCENARIOS EXECUTIVE
S TA B I L I Z AT I O N B A R
1
Allen Key
5mm
x2
M6 x 10mm
Cap Screw
2
Attach stabilization bar on side of the leg.
Place in plastic cap cover on both side of it.
M O D E S T Y PA N E L
1
2
Allen Key
4mm
Attach L-bracket with JCBC screws on the holes
for left & right side of melamine modesty panel.
Allen Key
5mm
JCBC Screw
x8
M8 x 16mm
x 12
M6 x 16mm
JCBC Screw
Attach melamine modesty panel to worktop.
3
Complete look for Scenarios Executive desk.
5
SCENARIOS S2S MANUAL SCENARIOS EXECUTIVE
CONTROL BOX
Attention:
Before starting the system, please make sure, that the operating voltage of the
system conforms with the local power supply. The mains plug of the control has
to be connected to a free accessible power supply.
* PLUG IN - FOLLOW THE INSTRUCTION BELOW.
FRONT VIEW
BACK VIEW
HS
MI
M2
DRIVE 1
DRIVE 2
D I S P L AY
1
x4
M3 x 13mm
S/D Screw
2
Bottom view - Attach control panel with S/D screws
at the bottom of the worktop.
Place control box in cabletray, tidy up all the cables into
the cabletray.
6
SCENARIOS S2S MANUAL SCENARIOS EXECUTIVE
SETTING
1
Memory 1,2,3,4
1
2
3
Display
4
S
2
Up Down
Up
1
--000
2
4
068
Handset = 68 - 118cmH
Handset
Store memory
3
S
Start up - Turn on the main power supply before
setting. Once the power is on, display flashes show
000 or ---.
Press and hold the down button until the lowest position
068 is reached (show in display, stop flashing), system is
ready for further programming,the maximum reachable
height is 118.
3
4
Up Down
1
2
3
4
S
Display
Memory 1,2,3,4
1
070
2
3
4
S
Up Down
068
Store memory
Normal operation - Press and hold up or down
until the desired height of the desk has been
reached, the display always shows the actual height.
Saving preferred height - 4 preferred heights can
be saved.
5
1
2
S
3
4
S000-
Memory 1,2,3,4
1
S
2
3
Display
4
6
S0001
Store memory
Move to the desired desk height. Press the store
memory ‘S’. You will see the display shows ‘S - ‘.
Press one of the memory keys, 1,2,3,4, and the number of the position height is displayed, a double click is
heard at the end of memory saved. Repeat the same
step of this for other preferred heights.
7
SCENARIOS S2S MANUAL SCENARIOS EXECUTIVE
SETTING
7
Memory 1,2,3,4
1
S
2
3
PLEASE REFER TO MARKANT
4
068
MOTOR CONNECTOR SET
USER MANUAL FOR
HEIGHT ADJUSTABLE DESK
FOR FURTHER HELP
Moving to a saved preferred height - Press and
hold one of the keys, 1, 2, 3, 4, the desk will moves
towards to the preferred height.
8