6” HYDRAULIC SUBMERSIBLE
VORTEX FLOW TRASH PUMP
MODEL S6T (Aluminum Body)
MODEL S6TDI (Ductile Iron Body)
6” (150 mm) Discharge
The S6T is our most popular 6" Pump. It
is lightweight, compact and able to pass
large solids, stringy materials and slurries
with entrained gases. This versatile top
discharge pump is designed for sewer
by-pass jobs, digester cleaning, plant
intake de-silting and inline pumping.
FEATURES
•
•
•
•
•
•
•
•
SPECIFICATIONS
Fully Recessed Vortex Impeller
(will pass 5" semi-solids)
WEIGHT: (Aluminum).................................... 202 lbs. (92 kg)
Variable Speed hydraulic drive provides a
wide range of performance
(Ductile Iron)............................... 330 lbs. (150 kg)
HEIGHT:.............................................................. 38" (96 cm)
WIDTH (@ widest point):.................................... 25" (63 cm)
Dependable gear type hydraulic motor
DISCHARGE:........................................................ 6" NPT(F)
INLET FLANGE:............................................ 6", 125# ASA
SOLIDS HANDLING:......................................... 5" (125 mm)
HOSE PORTS:................................................. 1" (-16) SAE
Can be bolted directly into a pipeline or
used as a booster pump
PUMP BODY: (S6T)...................... Heat Treated Aluminum
(S6TDI)...................................... Ductile Iron
IMPELLER:................................................... Stainless Steel
Safe Hydraulic Drive can be used where
electric power is hazardous or impractical
WEAR RING and WEAR PLATE.................. Stainless Steel
SHAFT:......................................................... Stainless Steel
SHAFT SEAL:.................................... Carbon/Ceramic (Std)
Oil Lubricated Seals (can run dry)
Optional silt jetting ring is available for
agitating solids into suspension
Operates with our HT50 to HT75 power
units or other hydraulic power sources
capable of flows of 15 - 30 GPM
G0413
Silicon Carbide (Optional)
ELASTOMERS:................................................ Buna N (Std)
HYDRAULIC OIL:................ 214-320 s.s.u. @ 100°F (64°C)
INPUT FLOW:................................ Max 30 GPM (114 LPM)
OPERATING PRESSURE:............ Max 3000 PSI (204 Bar)
POWER SOURCE:....... Any Open Center Hydraulic System
Specifications are subject to change without notice
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website: www.hydra-tech.com
E-Mail: [email protected]
Model S6T Overall Dimensions
18"
(46cm)
38"
(96cm)
6" NPT (FEMALE)
25"
(63cm)
25"
(63cm)
S6T Typical Performance
40
35
135
120
105
30
HYDRAULIC INPUT:
A) 17 GPM @ 900 - 2800 PSI
B) 20 GPM @ 1200 - 2900 PSI
C) 23 GPM @ 1500 - 2900 PSI
D) 26 GPM @ 1800 - 2900 PSI*
E) 28 GPM @ 2000 - 2900 PSI
E
D
* Typical performance with HT60 Power Unit
25
75
C
60
B
20
15
45
30
5
15
A
Feet
10
Meters
TOTAL HEAD
90
0
200
U.S.G.P.M.
400
1200
Liters/Minute
600
800
1000 1200 1400 1600 1800 2000
2400
3600
CAPACITY
4800
6000
7200
Curves are based on pumping water at 60°F. For performance curves other than shown above, consult factory.
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website: www.hydra-tech.com
E-Mail: [email protected]