SPECIAL PRODUCTS POLYVER SUPER POLYPRIMER HP WHITE STRADA POLYPRIMER HP STRADA is a high-performance, fast-drying solvent-based elastomeric bitumen primer. Guaranteed quality UNI EN ISO 9001:2008 and UNI EN ISO 14001:2004 Polyglass is a member of the Green Building Council Rev. 1-16 SPECIAL PRODUCTS TECHNICAL DESCRIPTION POLYPRIMER HP STRADA is an adhesion-promoting primer formulated with bitumen, elastomers, fast-drying select additives and pure solvents that is used to help the application of traditional and self-adhesive polymer bitumen membranes. WHERE TO APPLY POLYPRIMER HP STRADA is used as a fast adhesion-promoting primer to stop concrete dust and saturate open pores on flat and sloping concrete or metal surfaces as well as over old bitumen coverings to improve the adhesion of polymer bitumen membranes. POLYPRIMER HP STRADA can also be applied on asphalt and on slightly damp surfaces (maximum 3%) as well as on concrete bridge and viaduct decks. The elastomers used in the product’s formula help the application of polymer distilled bitumen membranes, both torch-on or self-adhesive, ensuring a more elastic dry film and excellent adhesion to the substrate. APPLICATION PROCEDURES AND TIPS POLYPRIMER HP STRADA can be applied by brush, roller or airless spray gun. All surfaces to be treated must be dry or slightly damp; they must also be clean, sound and free of oily or greasy residues. Once stirred, the product is ready for use and does not require thinning. The amount of product to be used will depend on substrate conditions and the thickness of the film you want to achieve: on concrete surfaces in a good state of repair, the amount of product will usually be approx. 200-350 g/m2; the consumption rate may drop to approx. 150 g/m2 on metal or bitumen surfaces. Subsequent waterproofing should be installed only once the film has been allowed to dry and, in any case, only when weather conditions are favourable. Following application, the film will usually take roughly 1 hour to dry, though it may take up to 2-4 hours when dealing with thick coats of material, harsh temperatures or surfaces that are not very absorbent. It is advisable to apply the first waterproof layer once the product has dried completely: usually waiting at least 12 hours. Before applying membranes, always make sure that the solvents have evaporated completely. The use of solvent-based products in populated areas where people live or work is not recommended: it is advisable to use a water-based primer “Idroprimer” for refurbishment projects or new roofs in such areas. It is also not advisable to use the product on wet or very damp surfaces, inside homes, in poorly ventilated areas, tanks or indoors in general. PRODUCT CHARACTERISTICS APPEARANCE COLOUR SPECIFIC WEIGHT AT 20 °C STANDARD EN ISO 2811-1 SOLID CONTENT - STANDARD EN ISO 3251 DUST DRY (23 °C - 50% RH) VISCOSITY DIN 53211 NOZZLE DIAMETER 4 AT 20 °C FRAASS BREAKING POINT OF BLOWN BITUMEN PENETRATION (DOW) OF BITUMEN AT 25 °C Liquid Black 0.95 (±0.04) kg/l 51-57 % 30-60 minutes 19-25 seconds -12 °C 15/20 dmm FLASH POINT (CLOSED CUP) TOUCH DRY PH AT 20 °C BOILING RANGE SOFTENING POINT (R&B) OF BITUMEN AUTOFLAMMABILITY STABILITY IN ORIGINAL SEALED TINS SURFACE TEMPERATURE FOR BEST USE <23 °C 100-140 minutes Neutral 80-190 °C 85-95 °C 245 °C 24 months >5 °C PACKAGING, STORAGE, EQUIPMENT CLEANING CONTAINERS STORAGE EQUIPMENT CLEANING PRODUCT FOR PROFESSIONAL USE The figures, information and suggestions result from the experience of POLYGLASS SPA. Anyone who uses Polyprimer HP Strada must ensure that the product is suitable for the specific use and application. In any case the installer is only person responsible for the correct application and therefore of all consequences arising from said application. Please always refer to our last version of the techncial data sheet on our site: www.polyglass.com. For any further information, please contact our technical office. POLYGLASS SPA reserves the right, without notice, to modify the technical card according to the necessity to improve the product. SAFETY REGULATIONS POLYPRIMER HP STRADA is highly flammable. You are advised to keep it away from sources of ignition, do not smoke, take precautionary measures against static discharge and work in well-ventilated areas. In addition, it is harmful by inhalation, may be fatal if swallowed and enters respiratory tract, is irritating to skin and may cause drowsiness and dizziness. You are advised to wear gloves, safety eyewear and a face mask fitted with filters during application, observing usual chemical handling precautions. In case of contact with eyes or skin, rinse immediately with plenty of water and seek medical advice. Do not use around pregnant women. For further, comprehensive information on how to use the product safely, you are advised to refer to the latest version of the Safety Data Sheet. 10/16 Rev. 1-16 20 l Shelf life of product in correctly sealed container, kept in a dry place, out of direct sunlight: 24 months Clean equipment with common solvents after use. POLYGLASS SPA Registered Office: Viale Jenner, 4 - 20159 MILANO Administrative Headquarters: Via dell’Artigianato, 34 - 31047 Ponte di Piave (TV) - Italy Tel. +39 04227547 - Fax +39 0422854118 - www.polyglass.com - [email protected]
© Copyright 2024 Paperzz