Filename: tfs433k.doc
Version 2.0
Vectron International
23.11.2016
Filter specification
TFS433K
1/5
Measurement condition
Ambient temperature TA:
Input power level:
Terminating impedance: *
Input:
Output:
23
0
°C
dBm
370 Ω || -0.9 pF
370 Ω || -0.9 pF
Characteristics
Remark:
The reference level for the relative attenuation arel of the TFS433K is the minimum of the pass band attenuation amin. The minimum of the pass band
attenuation amin is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB
filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed at 433.42 MHz without any tolerance. The given values for both the
relative attenuation arel and the group delay ripple have to be achieved at the frequencies given below even if the centre frequency fc is shifted due to the
temperature coefficient of frequency TCf within the operating temperature range and due to a production tolerance for the centre frequency fc.
Data
typ. value
Insertion loss
ae
4
Nominal frequency
fN
-
3 dB bandwidth
BW
260
Relative attenuation
arel
dB
tolerance / limit
max.
5
dB
433.42
MHz
Passband
fN
fN
fN
fN
fN
+
+
10
1.2
75
500
1.2
MHz
MHz
kHz
kHz
MHz
…
…
…
…
…
fN
fN
fN
fN
fN
- 1.2
- 500
+ 75
+ 1.2
+ 10
Operating temperature range
MHz
kHz
kHz
MHz
MHz
OTR
Storage temperature range
Frequency inversion temperature
T0
Temperature coefficient of frequency
TCf **)
kHz
min.
150
kHz
dB
dB
dB
dB
dB
min.
min.
max.
min.
min.
45
30
3
30
45
dB
dB
dB
dB
dB
-
-30 °C ... +70 °C
-
-55 °C ... +125 °C
25
°C
-0.032 ppm/K²
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values
only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
**) ∆ =
−
Generated:
Checked / Approved:
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs433k.doc
Version 2.0
Vectron International
23.11.2016
Filter specification
TFS433K
2/5
Filter characteristic
referenced to minimum attenuation in passband
0
-10
-30
S21 in dB
S21 in dB
-20
-40
-50
-60
-70
431.9
432.3
432.7
433.1
433.5
433.9
frequency in MHz
434.3
434.7
435.1
Construction and pin connection
(All dimensions in mm)
S433K
●
H48
3
Date code
2 Max.
1
Ground
Input
Ground
Ground
Ground
Ground
Ground
Output
Ground
Ground
Ground
Ground
Date code:
H
J
K
...
Year + week
2016
2017
2018
1
5,2 Max.
2,54 ± 0,2
7,2 Max.
2,54 ± 0,2
1
1
2
3
4
5
6
7
8
9
10
11
12
0,80
50 Ω Test circuit
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs433k.doc
Version 2.0
Vectron International
23.11.2016
Filter specification
TFS433K
3/5
Stability characteristics, reliability
After the following tests the filter shall meet the whole specification:
1. Shock:
500 g, 1 ms, half sine wave, 3 shocks each plane;
DIN IEC 60068 T2 - 27
2. Vibration:
10 Hz to 2000 Hz, 0.35 mm or 5 g respectively, 1 octave per min, 10 cycles per
plane, 3 planes; DIN IEC 60068 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
-55 °C to 125 °C / 15 min. each / 100 cycles
DIN IEC 60068 part 2 – 14 Test N
reflow possible: three times max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
5. SAW devices are Electrostatic Discharge (ESD) sensitive devices.
This filter is RoHS compliant (2011/65/EU)
Packing
Tape & Reel:
IEC 286 – 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
3000
min. 300 mm
min. 500 mm
min. 300 mm
Pull Off Direc tion
Tape (all dimensions in mm)
W
: 16.00 +0.3/-0.1
Po
: 4.00 ±0.1
Do
: 1.50 +0.1/-0
E
: 1.75 ±0.1
F
: 7.50 ±0.1
G(min)
: 0.75
P2
: 2.00 ±0.1
P1
: 8.00 ±0.1
D1(min)
: 1.50
Ao
: 5.40 ±0.1
Bo
: 7.60 ±0.1
Ct
: 13.30 ±0.1
Ko
: 2.00 ±0.1
t
: 0.30 ±0.05
Reel (all dimensions in mm)
A
: 330
or 180
W1
: 16.4 +2/-0
W2(max) : 22.40
N(min)
: 50.00
C
: 13.0 +0.5/-0.2
P1
t
PIN Marker
Po
P2
W
G
Ct
Bo
F
G
E
Do
Ko
Date Code
Typ
D1
Ao
W 2
C
A
N
W 1
The minimum bending radius is 45 mm.
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs433k.doc
Version 2.0
Vectron International
23.11.2016
Filter specification
TFS433K
4/5
Air reflow temperature conditions
Conditions
Average ramp-up rate (30 °C to 217 °C)
> 100 °C
> 150 °C
> 217 °C
Peak temperature
Time within 5 °C of actual peak temperature
Cool-down rate (Peak to 50 °C)
Time from 30 °C to Peak temperature
Exposure
less than 3 °C / second
between 300 and 600 seconds
between 240 and 500 seconds
between 30 and 150 seconds
max. 260 °C
between 10 and 30 seconds
less than 6 °C / second
no greater than 300 seconds
Chip-mount air reflow profile
Temperature / °C
max. 260 °C
217 °C
max. 300 s
10 ... 30 s
Time / s
30 ... 150 s
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs433k.doc
Vectron International
Version 2.0
Filter specification
23.11.2016
TFS433K
5/5
History
Version
Reason of Changes
Name
Date
1.0
- Generation of development specification
Steiner
01.01.1998
1.1
- Generation of filter specification
Steiner
01.05.1998
2.0
- Update all
Bonnen
23.11.2016
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.