Assembly Instructions
GEO
BOOKCASE 9 CUBE
STOP!
Before you start...
2
1
Read Instructions carefully.
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
3
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
location before fastening.
5
6
DO NOT over-tighten screws
DO NOT set glue until you are certain that the
parts belong together.
Page 2
What You Need
Top Panel
(P1)
(Tools not provided)
Phillips Head Srewdriver
Mallet
Mid Panel
(P4)
Shelf
(P5)
Left Side
Panel
(P3)
Shelf
(P5)
Mid Panel
(P4)
Shelf
(P5)
Shelf
(P5)
Shelf
(P5)
Rihgt Side
Panel
(P2)
Shelf
(P5)
Bottom Panel
(P6)
1 x allen key
16 x Long
Dowels
(H1)
6 x Allen
Bolts
(H5)
24 x Short
Dowels
(H2)
16 x Screws
(H6)
6 x Cam
Bolts
(H3)
2 x Brake
Wheels
(H7)
6 x Cam
Nuts
(H4)
2 x Wheels
(H8)
Page 3
Step 1
(P4)
You will need:
8 x Long
Dowels
(H1)
(P5)
(P5)
(P5)
(H1)
(P5)
(H1)
Insert the long dowels (H1) into the dowel holes of the mid panel (P4), connect the shelves (P5) to the
douwels which attached to the mid panel.
Step 2
(P4)
(P4)
You will need:
4 x Long
Dowels
(H1)
(H1)
Use the long dowels (H1) to conect the other mid panel (P4) to the step 1 shelves.
(H1)
Page 4
Step 3
(P4)
(P4)
You will need:
4 x Short
Dowels
(H2)
(H2)
(P5)
(P5)
(P5)
(P5)
(H2)
Connect the shelves (P5) to the long dowels that in the mid panel on Setp 2, Iisert the short dowels (H2)
into the Shelves (P5).
Step 4
(H2)
(H2)
(P3)
(P4)
(H2)
(H2)
You will need:
16 x Short
Dowels
(H2)
(P5)
(P4)
(P5)
(P5)
(H2)
(P2)
(P5)
(H2)
(H2)
Conect the left side panel (P3) and the right side panel (P2) to the shelves
(P5), then insert the short dowels (H2) into the dowel holes which on the top
and bottom of panels (P2) and (P3). .
(H2)
Page 5
Step 5
You will need:
6 x Cam
Bolts
(H3)
(H3)
(H3)
(P1)
Screw the cam bolts (H3) into the top panel (P1).
(P1)
Step 6
You will need:
6 x Cam
Nuts
(H4)
(H4)
(H4)
(P3)
(P4)
(H4)
(P4)
(P2)
Insert the cam nuts (H4) into the panels (P2),(P3) and (P4), cover the top panel (P1) to the those
panels. Rotate the cam nuts so the arrows point towards the incoming cam bolts.Push the top
panel (P1) into place and tighten the cam nuts.
Page 6
Step 7
(P3)
(P4)
(P4)
(P2)
You will need:
6 x Allen
Bolts
(H5)
(P6)
(H5)
(H5)
(H5)
Screw the bottom panel (P6) to the panels (P2),(P3),(P4) using the allen bolts (H5).
Step 8
(H6)
You will need:
16 x Screws
(H6)
(H8)
(H8)
(H7)
(P6)
(H7)
2 x Brake
Wheel
(H7)
2 X Wheel
(H8)
(P1)
Align each wheel with the 4 pilot holes in the bottom panel (P6). Place the two brake wheels
nearest to the front of the unit. Screw the castors into place with the screws (H6) .
Page 7
Step 9
The job is now complete!
In the interest of our environment
Please dispose of all packaging thoughtfully.
Page 8