1407 SERIES
| 10 kVDC
|
70,000 FT
|
-55º TO 105ºC
|
7-Pin
The 1407 Series is a ruggedized 7-pin, bayonet coupled connector family. The 1407 is another one of Teledyne Reynolds’ connector series that has been
used extensively in airborne Traveling Wave Tube (TWT) and TWT Amplifier (TWTA) applications.
The 1407 comes in, both, shielded and non-shielded configurations. Plug kits are available for customer-fabricated cable assemblies using Teledyne
Reynolds’ wire.
PLUG KIT
(Dimensions shown as in/mm)
Shielded (shown)
Non-shielded
167-9454 Uses Wire 167-8726
167-9571 Uses Wire 167-9609
• While plug kits are available for customer-fabricated cable assemblies, Teledyne Reynolds
highly recommends purchasing cable assemblies because of difficulties customers may
experience in assembly and testing.
• Assembly instructions can be found at www.teledynereynolds.com or by contacting Teledyne
Reynolds’ Engineering.
Ø 1.14”
29.0
1.52”
38.5
RECEPTACLE
Front, Box Flange Mount
Sealed, Rear, Jam Nut Mount
178-8996
MOUNTING HOLE
(Box Flange)
• Plastic Insulator
• Mounting: See optional Box
Flange mounting
1.13” Square
28.7 Flange
Note: Area must
be suitably
encapsulated for
altitude operation
Ø .120”
3.05 TYP.
Ø .930”
23.6
.79”
Ø 20.0
See Note
.53”
13.4
O-Ring
167-8625
.52”
13.4
• Silicone Insulator
.872”
Ø 1.39”
• Mounting: See optional Jam Nut
35.2 Ø 22.2
mounting hole
• Panel Mounting Torque: 48 ± 4 in-lbs
1.29”
• Pressure: Sealed for 1 ATM differential
32.9
pressure
• Max. Leak Rate: 1x10-6 cc/s He @1 ATM
MOUNTING HOLE
differential pressure
(Jam Nut)
.906” TYP.
23.0
Silicone rubber sleeve
(7 per assembly kit)
Note: Area
must be
suitably
encapsulated
for altitude
operation
1.01”
25.7
• Note: Contacts to be soldered to cable, inserted and bonded into insulator. Assembly
instructions can be found at www.teledynereynolds.com or by contacting Teledyne Reynolds’
Engineering.
.655”
16.7
PLUG CABLE ASSEMBLIES
SHIELDED
NON-SHIELDED
SINGLE-ENDED
DOUBLE-ENDED
WIRE P/N
167-9586
167-9603
167-9618
167-9607
167-8726
167-9609
**
RECEPTACLE CABLE ASSEMBLIES
**
Front, Box Flange Mount
Sealed, Rear, Jam Nut Mount
178-8956 Uses Wire 167-9543
167-8729 Uses Wire 167-9543
• Plastic Insulator
• Mounting: See optional Box Flange mounting hole
• Silicone Insulator
• Mounting: See optional Jam Nut mounting hole
• Panel Mounting Torque: 48 ± 4 in-lbs
• Pressure: Sealed for 1 ATM differential pressure
• Max. Leak Rate: 1x10-6 cc/s He @1 ATM differential pressure
MOUNTING HOLE
(Box Flange)
Ø .120”
3.05 TYP.
Ø .930”
23.6
1.13” Square
28.7 Flange
.58”
14.8
.89”
22.5
MOUNTING HOLE
(Jam Nut)
1.01”
25.7
O-Ring
.976”
24.8
.93”
Ø 23.5
.906“ TYP.
23.0
SERIES SPECIFICATIONS
Approx.
.500”
12.7
Tin Dip
1.48”
37.6
Series
Voltage
Rating
(kVDC)
Altitude
Rating (ft)
Operating
Temp. (ºC)
Current
Rating
(Amp)
Receptacle
Insulator
Material
1407
10
70,000
-55 to 125
6 or 8†
Silicone
Plug
Insulator
Material
Coupling
Style
Silicone
Bayonet
or Plastic
Coupling Nut
Material/
Finish
Al/Ni
Plug Contact Recept. Contact
Material/Finish Material/Finish
(Pin)
(Socket)
Brass/Au
Wire Type
Shielded
or Nonshielded
BeCu/Au
(• = Same value as above)
Test Voltage Test Voltage
Wire
Braid
@ 70,000 ft @ Sea Level
Insulation Termination
(kVDC)
(kVDC)
FEP
Band
15
N/A
WIRE SPECIFICATIONS
Conductor
Insulation
Shielding
Operating
Voltage
(kVDC)
AWG
Strands
Plating
Material
ø in./mm
167-8726
26
22
19/34
SPC
FEP
167-9609
30
20
19/32
TPC
•
Part #
Jacket
AWG
Plating
ø in./mm
0.100 / 2.54
36
SPC
•
N/A
N/A
Impedance
Ω
Attenuation
dB/100 ft @
400 MHz
Capacitance
pF/ft (Nom.)
@ 1 kHz
Material
ø in./mm
0.12 / 3.05
FEP
0.145 / 3.68
50
TBD
30
N/A
N/A
N/A
N/A
N/A
N/A
Current Rating value depending on the wire that is selected.
**Cable Assembly Ordering Information: All cable assembly cable lengths are to be specified in inches only. For example, to order part number 178-6027 with a cable length of 10 feet 8 inches the cable
assembly part number would be specified as 178-6027-128N.
• Note: Product numbers and specs subject to change without notice. • Products listed represent only a small selection of Teledyne Reynolds’ products please visit www.teledynereynolds.com for the
most up to date product information. • Contact Teledyne Reynolds’ Engineering to discuss custom designs. WARNING: Connectors should NEVER be handled mated or unmated when voltage is applied.
†
Rev. 100913
Approved for Public Release: AA-008/13
5
4