1407 SERIES | 10 kVDC | 70,000 FT | -55º TO 105ºC | 7-Pin The 1407 Series is a ruggedized 7-pin, bayonet coupled connector family. The 1407 is another one of Teledyne Reynolds’ connector series that has been used extensively in airborne Traveling Wave Tube (TWT) and TWT Amplifier (TWTA) applications. The 1407 comes in, both, shielded and non-shielded configurations. Plug kits are available for customer-fabricated cable assemblies using Teledyne Reynolds’ wire. PLUG KIT (Dimensions shown as in/mm) Shielded (shown) Non-shielded 167-9454 Uses Wire 167-8726 167-9571 Uses Wire 167-9609 • While plug kits are available for customer-fabricated cable assemblies, Teledyne Reynolds highly recommends purchasing cable assemblies because of difficulties customers may experience in assembly and testing. • Assembly instructions can be found at www.teledynereynolds.com or by contacting Teledyne Reynolds’ Engineering. Ø 1.14” 29.0 1.52” 38.5 RECEPTACLE Front, Box Flange Mount Sealed, Rear, Jam Nut Mount 178-8996 MOUNTING HOLE (Box Flange) • Plastic Insulator • Mounting: See optional Box Flange mounting 1.13” Square 28.7 Flange Note: Area must be suitably encapsulated for altitude operation Ø .120” 3.05 TYP. Ø .930” 23.6 .79” Ø 20.0 See Note .53” 13.4 O-Ring 167-8625 .52” 13.4 • Silicone Insulator .872” Ø 1.39” • Mounting: See optional Jam Nut 35.2 Ø 22.2 mounting hole • Panel Mounting Torque: 48 ± 4 in-lbs 1.29” • Pressure: Sealed for 1 ATM differential 32.9 pressure • Max. Leak Rate: 1x10-6 cc/s He @1 ATM MOUNTING HOLE differential pressure (Jam Nut) .906” TYP. 23.0 Silicone rubber sleeve (7 per assembly kit) Note: Area must be suitably encapsulated for altitude operation 1.01” 25.7 • Note: Contacts to be soldered to cable, inserted and bonded into insulator. Assembly instructions can be found at www.teledynereynolds.com or by contacting Teledyne Reynolds’ Engineering. .655” 16.7 PLUG CABLE ASSEMBLIES SHIELDED NON-SHIELDED SINGLE-ENDED DOUBLE-ENDED WIRE P/N 167-9586 167-9603 167-9618 167-9607 167-8726 167-9609 ** RECEPTACLE CABLE ASSEMBLIES ** Front, Box Flange Mount Sealed, Rear, Jam Nut Mount 178-8956 Uses Wire 167-9543 167-8729 Uses Wire 167-9543 • Plastic Insulator • Mounting: See optional Box Flange mounting hole • Silicone Insulator • Mounting: See optional Jam Nut mounting hole • Panel Mounting Torque: 48 ± 4 in-lbs • Pressure: Sealed for 1 ATM differential pressure • Max. Leak Rate: 1x10-6 cc/s He @1 ATM differential pressure MOUNTING HOLE (Box Flange) Ø .120” 3.05 TYP. Ø .930” 23.6 1.13” Square 28.7 Flange .58” 14.8 .89” 22.5 MOUNTING HOLE (Jam Nut) 1.01” 25.7 O-Ring .976” 24.8 .93” Ø 23.5 .906“ TYP. 23.0 SERIES SPECIFICATIONS Approx. .500” 12.7 Tin Dip 1.48” 37.6 Series Voltage Rating (kVDC) Altitude Rating (ft) Operating Temp. (ºC) Current Rating (Amp) Receptacle Insulator Material 1407 10 70,000 -55 to 125 6 or 8† Silicone Plug Insulator Material Coupling Style Silicone Bayonet or Plastic Coupling Nut Material/ Finish Al/Ni Plug Contact Recept. Contact Material/Finish Material/Finish (Pin) (Socket) Brass/Au Wire Type Shielded or Nonshielded BeCu/Au (• = Same value as above) Test Voltage Test Voltage Wire Braid @ 70,000 ft @ Sea Level Insulation Termination (kVDC) (kVDC) FEP Band 15 N/A WIRE SPECIFICATIONS Conductor Insulation Shielding Operating Voltage (kVDC) AWG Strands Plating Material ø in./mm 167-8726 26 22 19/34 SPC FEP 167-9609 30 20 19/32 TPC • Part # Jacket AWG Plating ø in./mm 0.100 / 2.54 36 SPC • N/A N/A Impedance Ω Attenuation dB/100 ft @ 400 MHz Capacitance pF/ft (Nom.) @ 1 kHz Material ø in./mm 0.12 / 3.05 FEP 0.145 / 3.68 50 TBD 30 N/A N/A N/A N/A N/A N/A Current Rating value depending on the wire that is selected. **Cable Assembly Ordering Information: All cable assembly cable lengths are to be specified in inches only. For example, to order part number 178-6027 with a cable length of 10 feet 8 inches the cable assembly part number would be specified as 178-6027-128N. • Note: Product numbers and specs subject to change without notice. • Products listed represent only a small selection of Teledyne Reynolds’ products please visit www.teledynereynolds.com for the most up to date product information. • Contact Teledyne Reynolds’ Engineering to discuss custom designs. WARNING: Connectors should NEVER be handled mated or unmated when voltage is applied. † Rev. 100913 Approved for Public Release: AA-008/13 5 4
© Copyright 2024 Paperzz