EN0H-0468GE25 R0516
Water Metering
S110
Singlejet Water Meters
DN15 and DN20 for Cold and Warm Potable Water Applications
APPLICATION
Honeywell S110 singlejet water meters are used for sub
metering of cold or warm water in residential drinking water
systems.
They are available in sizes DN15 and DN20 and have a
mechanical counter. They can be retrofitted with a clip on MBus and pulse out combimodule for integration into remote
readout networks.
APPROVALS
•
MID 2014/32/EU (based on OIML R49, EN14154)
•
ACS, UBA, KTW
SPECIAL FEATURES
•
Retrofittable with wired M-Bus / pulse out
communication
TECHNICAL DATA
Media
Standard medium:
Connections
Nominal sizes:
Nominal flow Q3:
Operating temperatures
Medium temperature:
Temperature class:
Ambient temperature:
Specifications
Water pressure class:
Pressure loss class:
Environmental class:
Mechanical class:
Electromagnetic class:
Measuring process:
Display:
Display unit:
Display range:
Increments:
Acceptable error:
Installation position:
Optional interfaces:
Drinking water
DN15 - DN20
2.5 - 4 m³/h
Cold water: 0.1 - 30 °C
Warm water: 30 - 90 °C
Cold water: T30
Warm water: T30/90
5 - 55 °C
MAP16 (max. 16bar)
ΔP63 (max. 63kPa)
B
M1
E1
Mechanical counter with
singlejet volume
measurement
8-digit roller counter
m3
105 with four decimal places
0.00005 m3
±2% at Q3 for water ≤30 °C
±3% at Q3 for water >30 °C
H, V (horizontal, vertical)
Wired M-Bus and pulse out
Product Specification Sheet • EN0H-0468GE25 R0516 • Subject to change
1
S110 - Singlejet Water Meters
CONSTRUCTION
Overview
1
2
3
4
5
6
7
8
9
METHOD OF OPERATION
Counter
•
The meter can be read from a single line eight-digit roller
counter with m³. The counter unit can be rotated for
better readibility.
Components
Roller counter
Serial number
Inlet
Outlet
Approval number and
specifications
Cover of module interface
Target
CE marking and production
year
Flow arrow
Materials
Plastic
Brass
Brass
Plastic
-
master or, in case the meter is not attached to an M-Bus,
with an M-Bus hardware tool, for example the Relay
Micro-Master.
Flow Sensor
•
The singlejet technology of the flow sensor combines
high measuring accuracy with long term stability. The
impeller is connected to the counter by a magnetic
coupling. The flow sensor has a sieve on the inlet to stop
particles from entering the measuring chamber.
Interfaces
•
S110 water meters can be retrofitted with the TMP-F
clip on communication module for remote readout
applications. The TMP-F module provides M-Bus and
pulse out options. Both options can be operated in
parallel. The module is clipped onto the meter in the field
and can be fitted at any time, also when the meter is
already operating. The module is supplied ready to use.
Programming is required in case default values should
be changed.
M-Bus / pulse out combination module
•
M-Bus / pulse out combination module: The M-Bus /
pulse out combination module has cables for wiring to
an M-Bus and to a pulse counter. The M-Bus module is
according to EN13757-3 with primary and secondary
addressing. Programming is done via the M-Bus master.
M-Bus address changes are done with the M-Bus
master configuration software, for example MBConf.
Pulse module configuration is also done via the M-Bus
TRANSPORTATION AND STORAGE
Keep parts in their original packaging and unpack them
shortly before use.
The following parameters apply during transportation and
storage:
Parameter
Environment:
Min. ambient temperature:
Max. ambient temperature:
Min. ambient relative
humidity:
Max.ambient relative
humidity:
Value
clean, dry and dust free
-20 °C
70 °C
5%*
95 % *
*non condensing
2
Product Specification Sheet • EN0H-0468GE25 R0516 • Subject to change
S110 - Singlejet Water Meters
INSTALLATION GUIDELINES
TECHNICAL CHARACTERISTICS
Setup requirements
Flow Data
•
Calming legs before or after S110 water meters are not
required unless the meter is installed before or after a
pump or motorised valve. In that case a calming leg
of 5 x DN is required in front of or of 3 x DN behind
the meter.
•
All sizes may be installed in both horizontal and vertical
position.
•
S110 water meters must be installed with dial facing upwards or sidewards but not beneath the horizontal
plane.
•
Avoid installation at highest point of system or system
part as air may be trapped in meter
•
It is recommended to place a valve before and after the
meter for easy replacement.
•
During measurement meter must be completely filled
with water
Nominal size diameter:
Flow rates
Minimum (Q1):
Transitional (Q2):
Permanent (Q3):
Overload (Q4):
Dynamic range (Q3/Q1):
Additional flow data
Starting flow:
DN
15, 20
20
l/h
l/h
m3/h
m3/h
63
100
2.5
3.125
R40
100
160
4
5
R40
7
10
l/h
Sizing
•
S110 water meters should be selected in such a way that
permanent system flow rates are between transition
flow rate (Q2) and permanent flow rate (Q3)
•
The flow rate may not drop below minimum (Q1) or
exceed overload flow rate (Q4) at any time
DIMENSIONS
Overview
Note:
Parameter
Nominal size diameter:
Meter thread G:
Weight:
Dimensions:
All dimensions in mm unless stated otherwise.
Note:
Values
DN
Inch
kg
L
H1
H2
ØD
15
G3/4 "
0.3
110
58
71
20
G1 "
0.4
130
58
74
64
Weight is without fittings or any other accessories.
ORDERING INFORMATION
The following tables contain all the information you need to make an order of an item of your choice. When ordering, please
always state the type, the ordering or the part number.
Options
Nominal size
diameter:
DN
15
15
20
20
Flow rate:
Length:
Ordering Number
Q3
2.5 m³/h
2.5 m³/h
2.5 m³/h
4 m³/h
80 mm
110 mm
130 mm
130 mm
for cold water
LA0003518
LA0003519
LA0005650
LA0003521
for warm water
LA0003814
LA0003816
LA0005651
LA0003818
S110 Scope of Delivery
•
S110 water meter
•
Two paper sealings
•
Installation and setup instructions
Product Specification Sheet • EN0H-0468GE25 R0516 • Subject to change
3
S110 - Singlejet Water Meters
Accessories
Description
EWA1
Connection set
V4020
V4000
TMP-F
Environmental & Energy Solutions
Honeywell GmbH
Hardhofweg
74821 MOSBACH
GERMANY
Phone: (49) 6261 810
Fax: (49) 6261 81309
http://ecc.emea.honeywell.com
Dimension
Part No.
Set of two union nuts, two sealings and two externally threaded brass tailpieces
(one pack per meter required) – sealable with locking wire
1/ " x 3/ "
For DN15
EWA1500035
2
4
3/ " x 1"
For DN20
EWA1500042
4
Alwa shutoff valves with internal threads
1/ " internal
For DN15
V4020YY015
2
threads
3/ " internal
For DN20
V4020YY020
4
threads
Alwa shutoff valves with internal threads and closed body
3/ " internal
For DN20
4
threads
Wired M-Bus / pulse out combination module
For DN15-20, available approx. Q3/2016
Manufactured for and on behalf of the
Environmental and Combustion Controls
Division of Honeywell Technologies Sàrl, Z.A.
La Pièce 16, 1180 Rolle, Switzerland
by its Authorised Representative Honeywell GmbH
EN0H-0468GE25 R0516
Subject to change
© 2016 Honeywell GmbH
V4000YY020