Pneumatic Actuators DA – Double acting TORQUE Nm TORQUE Nm 4 bar 6 bar Type 0° 50° 90° 0° 50° 90° RC210-DA RC220-DA RC230-DA 25 51 96 12 25 47 18 36 69 RC210-DA RC220-DA RC230-DA 38 76 145 19 38 72 27 54 105 RC240-DA RC250-DA RC260-DA 195 300 610 97 150 300 140 215 440 RC240-DA RC250-DA RC260-DA 290 450 910 145 225 460 210 320 650 RC265-DA RC270-DA RC280-DA 864 1260 2540 406 630 1270 614 910 1830 RC265-DA RC270-DA RC280-DA 1296 1890 3800 609 940 1900 921 1360 2740 0° 50° 90° Type 7 bar 5,5 bar 0° 50° 90° RC210-DA RC220-DA RC230-DA 34 70 130 17 35 66 25 50 95 RC210-DA RC220-DA RC230-DA 44 88 165 22 44 83 32 63 120 RC240-DA RC250-DA RC260-DA 270 410 840 135 210 420 190 300 600 RC240-DA RC250-DA RC260-DA 340 530 1070 170 260 530 240 380 770 RC265-DA RC270-DA RC280-DA 1188 1730 3500 559 860 1750 844 1250 2500 RC265-DA RC270-DA RC280-DA 1512 2200 4450 711 1100 2220 1075 1590 3190 Type Type AIR CONSUMPTION RC200-DA OPERATION TIME RC200-DA Free air at 6 bar air pressure At 6 bar air pressure Anticlockwise rotation dm3 Clockwise rotation dm3 RC210-DA RC220-DA RC230-DA 0,6 1,1 2,2 1,1 1,3 4,0 RC210 RC220 RC230 <0,25 <0,25 <1 <0,5 <0,3 <0,25 RC240-DA RC250-DA RC260-DA 4,4 6,9 13,8 5 13 16 RC240 RC250 RC260 <1 <1,5 <2 <1 <2,5 <2,5 RC265-DA RC270-DA RC280-DA 32 33 66 36 54 67 RC265 RC270 RC280 <1,5 <4 <5 <1,5 <6 <5 Type Type Anticlockwise rotation sec. Clockwise rotation sec. The times relate to full air flow and may increase depending on solenoid valves and the dimensions of connecting pipes. RC 270-280 Depth: Depth: Depth: RC 210-260 RC 250-280 RC 210-240 Depth: Depth: Depth: Depth: Depth: Depth: 12 Technical data: Max. working pressure 10 bar. Operating medium: air or inert gases. On request also low pressure hydraulics. Ambient temperature: –20 to +80 °C. Actuators for other temperature ranges can be delivered on request. MEASUREMENTS RC200-DA Standard design N.FI A B RC210-DA F05 45 98 RC220-DA F05 98 98 RC230-DA F07 65 135 RC240-DA F10 135 135 RC250-DA F10 90 190 RC260-DA F12 190 190 RC265-DA F12 195 195 RC270-DA F14 145 300 RC280-DA F16 300 300 C E F G H 32 41 75 16 10 49 55 110 25 J K 35,4 35,4 M N 40 30 FI P S 155 35 110 76 110 202 248 35 60 22 22 40 S1 T1 _ _ _ _ F05 50 M6 11 50 M6 11 30 – – 130 17 21 70 F07* 70* F12* 125* M12* 21* F10 F12 125 M12 76 P1 F10* 102* M10* 17* F07 16 80 75 FI F05 F10 102 M10 69 T U 35 Z Weight kg 14 19 1,2 14 19 1,6 17 M8 14 55 14* 70 17 70 F10* 102* M10* 17* Y** 35 M8* 102 M10 V 2 3 85 22 27 30 3,5 30 4,9 37 9,4 37 12,5 F12 125 M12 21 - - - - 85 3 27 37 18,8 F14 140 M16 25 - - - - 100 4 36 64 32,0 F16 165 M20 32 F12* 125* M12* 25* 130 5 46 64 42,0 N.Fl = Nominal ISO/DIN flange. I.e. mounting hole circle to valve, guide ring diameter U and measure Y follow the same standard flange. SV = Connection to solenoid valve on RC270–280. * = Extra mounting holes on all RC230–260 and 280 for alternative ISO/DIN hole pattern. ** = Tolerance H9. The hole is octagonal and adapts to valve stems with squares both in 90° and 45° direction. RC265: Extra mounting holes on the bottom side, please see leaflet No. 886. RC270 also has the following hole pattern on the bottom side: CC 170 x 110 mm placed alongside the actuator, 4 pcs M16, depth 25 mm. RC280 also has the following hole pattern on the bottom side: CC 234,7 x 97,2 mm, 4 pcs M16, depth 25 mm, which corresponds to 4 pcs of 8 pcs F25-holes. Regarding special designs: Please ask for a special brochure from Remote Control. We reserve our right for modifications caused by technical development Remote Control Sweden AB · Kontrollvägen 15 · SE-791 45 Falun, Sweden · Tel +46 23 587 00 · Fax +46 23 587 45 [email protected] · www.remotecontrol.se Ref No 856B/Art No 980856 Type
© Copyright 2024 Paperzz