Lifting Magnets
Model CREM - Permanent Lifting Magnets
The Caldwell Group
PRODUCT FEATURES:
• On/off powerful permanent magnetic.
• For use on flat or round material.
• Completely self contained.
• Simple level operation with safety lock.
• Permanent magnets holding power is not affected by power outages
or battery life.
• Complies with ASME standards.
B
A
C
HR
H
L
W
SPECIFICATIONS
Lift Capacity (lbs.)*
Plate
Round
250
110
800
330
1600
650
2500
1100
5000
2200
6600
3000
W
2.55
3.48
4.68
6.8
8.88
8.88
L
3.3
6.15
8.94
10
14.5
17.19
H
2.84
3.8
4.68
6.63
8.63
8.63
Dimensions (in.)
HR
4.35
6.35
7.88
11
14.88
14.88
A
0.31
0.46
0.63
0.78
1.1
1.1
B
1.17
1.57
2.05
3.45
4.38
4.38
Weight
(lbs)
10
20
48
100
250
440
C
1.51
2.55
3.2
4.37
6.25
6.25
*3 to 1 Safety Factor on Ground Mild Steel (see “Min. Thickness”, “Max. OD”), see derating Factors for thinner plate
LIFTING VALUE & *MAXIMUM SHEET LENGTH FOR SPECIFIED MATERIAL THICKNESS
CREM-0250
Capacity
Max. Size
(lbs.)
(ft. x ft.)
136
2.5 x 2.5
159
2.5 x 2.5
193
2.5 x 2.5
215
2.5 x 2.5
227
2.5 x 2.5
238
2.5 x 2.5
250
2.5 x 2
CREM-0800
Capacity
Max. Size
(lbs.)
(ft. x ft.)
242
3x3
320
3.5 x 3.5
356
3.5 x 3.5
399
3.5 x 3.5
490
3.5 x 3.5
635
3.5 x 3.5
713
3.5 x 3.5
800
3.5 x 3.5
CREM-1600
Capacity
Max. Size
(lbs.)
(ft. x ft.)
315
4x4
475
4 x 4.5
565
4.5 x 4.5
635
4.5 x 4.5
8900
4.5 x 4.5
1005
4.5 x 4.5
1195
4.5 x 4.5
1410
4.5 x 4.5
1600
4.5 x 4.5
CREM-2500
Capacity
Max. Size
(lbs.)
(ft. x ft.)
510
565
635
735
870
1245
1420
1815
1985
2385
2500
4.5 x 4
5 x 4.5
5 x 4.5
5 x 4.5
5 x 4.5
5 x 4.5
5 x 4.5
5 x 4.5
5 x 4.5
5 x 4.5
5 x 4.5
CREM-5000
Capacity
Max. Size
(lbs.)
(ft. x ft.)
1480
1950
2310
2590
3240
3515
4070
4525
5000
6x6
6x6
6x6
6x6
6x6
6x6
6x6
6x6
6x6
CREM-6600
Capacity
Max. Size
(lbs.)
(ft. x ft.)
2355
2945
3300
4125
4475
5185
5990
6360
6600
*Max sheet length due to sag for material thickness for single magnet use.
All capacities are based on lifting clean, smooth, flat low-carbon steel plate with the full area of the magnet’s lifting surface in
contact with the load. Derating is required for plates or other loads with rust or scale. Do not use on material thinner than 1/4".
F.44
NOTE: We recommend when lifting sheets over 8', use 2 or more lifts on a lifting or spreader beam to prevent sheet flexing,
sagging or peel-off. Thin material is susceptible to magnetic bleed through, resulting in two sheets being lifted at once.
7 x 6.5
7 x 6.5
7 x 6.5
7 x 6.5
7 x 6.5
7 x 6.5
7 x 6.5
7 x 6.5
7 x 6.5
Rig-Master® Section
2014-2016 Master Catalog
Sheet
Thickness
(in.)
1/4"
3/8"
7/16"
5/8"
3/4"
1"
1-1/4"
1-9/16"
1-3/4"
2-3/16"
2-3/8"
2-3/4"
3-1/8"
3-3/8"
3-1/2"
• 800-628-4263 • www.caldwellinc.com
Model
Number
CREM-0250
CREM-0800
CREM-1600
CREM-2500
CREM-5000
CREM-6600