ABSA0001 20cm (8”)
Max. Load: 200kg (31st)
Assembly Instructions
Positioning
Assemble the bathseat by inserting the three sucker
feet and the Surefoot sucker into the sockets.
With the Surefoot sucker lever in the up position,
place the bathseat into a dry bath positioned as
shown below.
The Surefoot sucker must be inserted as shown: -
Ensure all of the suckers are in direct contact with the
bath and not obstructed by the plug-hole. Move the
Surefoot sucker to the alternate position (*) shown in
figure 1 if necessary.
Surefoot sucker
Cut-out
(Front)
Alternate
position*
figure 1.
Ensure each foot is pushed all the way in and the
clips have engaged.
Position in bath, with optional bathboard (available separately).
Surefoot Sucker
Press down firmly on all 4 legs to secure the bathseat
in position. Press the lever down to achieve suction
and lock in place.
Press firmly
Lock
Maintenance
x4
Ensure each foot is pushed
all the way in and the clips
have engaged as shown.
To remove the seat: lift up the surefoot sucker lever,
pull up the three remaining sucker tabs and lift out.
The feet must be inserted
in the orientation shown.
Safety
Check the seat is secure before each use.
Only use as instructed. Assemble only as shown.
Sucker tab
Unlock
Do not store in direct sunlight.
Clean with warm water and nonabrasive cleaners
suitable for plastic baths.
Inspect for signs of fatigue regularly.
Can be autoclaved for sterilisation purposes.
Keep these instructions for future reference.
ABSX0001 Issue 1
Follow the above steps to reposition the seat in the
bath.
5cm (2”) Extensions Legs HA0672
The Surefoot bathseat can be fitted with extension
legs to increase the height to 25cm (10”) or 30cm
(12”) as desired.
For assembly and fitting follow the instructions
overleaf with the extension legs inserted in the
bathseat first as shown below.
Surefoot® Bathseat Upgrade Kit
ABSA0004
Use the Surefoot bathseat upgrade kit to convert a
Kingfisher bathseat (HA0670) to a Surefoot bathseat
for extra security and reassurance.
The upgrade kit adds 5cm (2”) to the height of the
seat.
Assembly Instructions
Remove the existing sucker feet from the bathseat by
pushing the clip in (1) and pulling the foot out (2).
Extension
Legs
Insert three of the feet into the extension legs. One of
the feet will be left over as a spare.
Existing
foot
Important
Use a maximum of three extensions per leg.
A 30cm seat must be down-rated to 160kg
(25st) maximum load.
When the Surefoot sucker is inserted
into an extension leg the clip
must be pushed into
position from the inside.
Insert a finger or thumb
into the opening and push the
clip firmly until it clicks into
position.
Press
Firmly
Extension
Leg
x3
Spare x1
Ensure the feet are orientated correctly and clips are
engaged fully on each leg.
Follow the instructions overleaf to fully assemble and
fit the Surefoot bathseat.
Product Codes
20cm (8”) Surefoot bathseat . . . . . . . . . . . . . . . ABSA0001
25cm (10”) Surefoot bathseat . . . . . . . . . . . . . . ABSA0002
30cm (12”) Surefoot bathseat . . . . . . . . . . . . . . ABSA0003
Surefoot bathseat upgrade kit . . . . . . . . . . . . . ABSA0004
5cm (2”) extension legs (set of four legs) . . . . HA0672
1 set of extension legs
25cm (10”) 200kg max.
(ABSA0002)
2 sets of extension legs
30cm (12”) 160kg max.
(ABSA0003)
Bromyard Road, Ledbury
Hereford HR8 1NS
Tel: (01531) 635678
Fax: (01531) 635670
[email protected]
www.helpinghand.co.uk