Technical Information
SERIES
9600
Interior/Exterior Acrylic
Traffic Marking Paint
Conco 9600 Series Interior/Exterior Acrylic Traffic Marking
Paint is a premium quality coating for striping and marking
streets, parking lots, and traffic and vehicle control areas.
Recommended Uses
Concrete & Asphalt
Parking Lots, Curbs &
Streets
Traffic & Vehicle Control
Areas
Performance Benefits
No Traffic Pick-Up After
45 Minutes
Abrasion Resistant
High Visibility Colors
Easy Spray Application
Ready to Use
Water Clean Up
Glass Beads May Be Added
For Reflective Markings
Certification
Master Painters Institute: MPI # 97, GPS-1
Recommended Systems
Concrete, Asphalt
1 or 2 coats Conco 9600 Series Acrylic Traffic Marking Paint
Warranty:
If this product, when applied according to label instructions, fails to perform to
your complete satisfaction, we will either replace an equivalent quantity of
product free of charge or refund the purchase price, upon presentation of
proof of purchase. This warranty does not include labor or costs associated
with labor for the application of any product. This warranty gives you specific
legal rights, and you may have other rights, which vary from state to state.
Finish:
Flat
Colors:
Striping White, Striping
Yellow, Curb Red,
Handicap Blue
Drying Time: (@ 15 mils wet, 77°F, 50% RH)
No Traffic Pick-Up:
45 Minutes
Spread Rate (@ 15 mils wet):
110 Sq. Ft. /Gal
(320 lineal feet per gallon of
standard 4” line)
Film Thickness:
15.0 mils wet
8.3 – 8.9 mils dry
Volume Solids:
Striping White
Striping Yellow
Curb Red
Handicap Blue
59% ± 2%
59% ± 2%
55% ± 2%
56% ± 2%
Weight Solids:
Striping White
Striping Yellow
Curb Red
Handicap Blue
76% ± 2%
75% ± 2%
70% ± 2%
71% ± 2%
Weight per Gallon:
Striping White
Striping Yellow
Curb Red
Handicap Blue
13.70 lbs
13.41 lbs
12.34 lbs
12.51 lbs
Vehicle Type:
Acrylic
Flash Point:
150°F, PMCC
V.O.C. Level:
Striping White
Striping Yellow
Curb Red
Handicap Blue
87 g/L; 0.73 lb/gal
87 g/L; 0.72 lb/gal
89 g/L; 0.74 lb/gal
86 g/L; 0.71 lb/gal
Reduction:
Not recommended
Cleanup:
Soap and water
Size:
Available in Ones
and Fives*
(*5’s by special order only)
Revised 12/09
Surface Preparation
WARNING! Removal of old paint by sanding, scraping or other means may
generate dust or fumes that contain lead. Exposure to lead dust or fumes
may cause brain damage or other adverse health effects, especially in
children or pregnant women. Controlling exposure to lead or other
hazardous substances requires the use of proper protective equipment,
such as a properly fitted respirator (NIOSH approved) and proper
containment and cleanup. For more information, call the National Lead
Information Center at 1-800-424-LEAD (in US) or contact your local health
authority.
Preparation
Surface must be cured, clean, dry and free from loose dirt, dust, grease, oil
and peeling paint. Previously painted lines may be repainted without
additional surface preparation if the old paint is still tightly adhered to the
surface. However, multiple layers of paint will eventually peel and require
removal.
Concrete
Remove concrete sealers and efflorescence on new concrete by extended
weathering, etching or abrasive blasting. Etch new concrete surfaces with
muriatic acid before painting.
Asphalt
Allow new asphalt surfaces to age at least 30-60 days before striping.
Shrinkage of the paint film during curing and exceeding the recommended
film thickness can cause new asphalt to lift or crack. Placing an
inconspicuous test stripe to determine if a new asphalt surface has cured
sufficiently to paint is recommended. If it is necessary to paint new asphalt
surfaces, apply two light coats (7-8 mils wet) to minimize cracking and/or
lifting of the asphalt.
Cleanup Information
Clean spills and spatters immediately with soap and warm water. Clean
hands and tools immediately after use with soap and warm water. After
cleaning, flush spray equipment with mineral spirits to prevent rusting of the
equipment. Follow manufacturer’s safety recommendations when using
mineral spirits.
SERIES
9600
Interior / Exterior Acrylic
Traffic Marking Paint
Application
Apply only when the surface, air and material are
above both 50°F and the dew point, and the
relative humidity is less than 85%.
Airless Spray Line Striping Equipment
Pressure…………………..1800 - 2700 psi
Hose……………………….…1/4” – 3/8” ID
Tip……………………………0.015”-0.019”
Filter……………………………...60 Mesh
Conventional Spray Line Striping Equipment
Follow equipment manufacturer’s
recommendations.
Brush (small areas only)
Use a quality nylon/polyester brush.
Roller (small areas only)
Use a 3/8” nap synthetic roller cover.
Thinning
Up to 12.5% by volume with water as needed.
Tips for Better Performance
Stir well before using
Glass beads may be dropped onto wet paint
for making reflective markings.
Start with a clean surface
Remove concrete sealers and efflorescence
Etch new concrete surfaces
Cautions
Keep from freezing
Painted surfaces can become slippery when
wet. Traffic paint should not be used to paint
large surfaces subject to pedestrian traffic
such as ramps, floor and stairs.
The information and recommendations set forth in this Product
Data Sheet are based upon tests conducted by or on behalf of
Conco Paints. Information and recommendations set forth
herein are subject to change and pertain to the product offered
at the time of publication. Consult your Conco Paint retailer or
sales representative to obtain the most recent Product Data
Sheet.