Instruction Manual
Installation Manual
Hanging cabinet storage system
Combination Rack
Installation Part
■ Read this installation manual carefully to install Combination Rack
safely. Especially, be sure to read “Safety Precautions” before
installation.
■ After installation, hand this installation manual/instruction manual to the
customer and explain how to use Combination Rack.
Safety Precautions
Be sure to observe the following
precautions.
The following explains the points to be observed in order to prevent harm to the users and damage to the
property.
■ The following explains possible harm and
damage by severity level, which may be
generated by wrong operation.
Warning
Caution
■ The following symbols are used to explain
the points to be observed. (These shown
below are examples of graphic symbols.)
You may die or get
seriously injured if you
ignore.
You may be slightly injured
or your property may be
damaged if you ignore.
Things that you must not do
Things that you must do
Warning
Prohibited
● Never disassemble, repair or
remodel the product.
These actions may cause fall or
failure of the equipment.
Be sure to
observe.
● Be sure to use the designated
screws to install the unit.
Otherwise, the unit may fall, and
accordingly injure you.
Accessories
Part name
(Dimensional unit: mm)
Quantity
Part name
Temporary locking screw
Quantity
1
Truss head tapping screw
4X14
2
Main unit
W900/750/600
Main unit mounting screw
Flat-head screw
M6x26
Blindfold cap
2
Main unit mounting bolt
Joint bolt
M4X16
Joint nut
4
Instruction manual/
installation manual
2 each
1
Installation Position
(Dimensional unit: mm)
Before installing the hanging cabinet, place it on the floor and drill the main unit mounting holes (piercing
holes (∅8) and temporary locking pilot holes (∅3)) on the bottom of the hanging cabinet.
* If there is a window frame around the installation place, shift the hole positions forward.
W900 type
∅8 piercing holes (4)
∅3 temporary locking pilot holes (2)
W750 type
∅8 piercing holes (4)
∅3 temporary locking pilot holes (2)
* Depth is the same as for W900 type.
Precautions for layout
W600 type
∅8 piercing holes (4)
∅3 temporary locking pilot holes (2)
* Depth is the same as for W900 type.
(Dimensional unit: mm)
To install Combination Rack, be sure to keep at least 150 mm interval from the cooking appliances.
 W750 Hood
Isolation distance 150 mm
 W900 Hood
Isolation distance 150 mm or more
■Installation of lighting equipment
Install the lighting equipment in such a way that it
will not interfere with open/close of Combination
Rack door.
Pay attention to
interference!
Installation
1.
(Dimensional unit: mm)
Set the truss head taping screws
(accessories) into the temporary locking
pilot holes (∅3 at two points) by floating
approx. 3 mm from the bottom plate surface.
Mounting
pilot holes
Temporary locking
pilot holes
2. Align the inserted tapping screws to the half
Temporary
locking screw
tumbler-shaped holes of the main unit. Slide
the tapping screws backward to temporarily
lock the unit.
Truss head
tapping screws
3.
Lock the unit by tightening the main unit
mounting screws and bolts (accessories)
into the mounting pilot holes (∅8 at four
points) drilled on the bottom of the hanging
cabinet.
Clamp hexagon cap nuts firmly with a spanner or equivalent.
Main unit
mounting screw
4.
Cover the blindfold caps over the mounting
screw heads on the hanging cabinet internal
bottom.
Joint bolt
Main unit
mounting
screw
Joint bolt
Blindfold
cap
Joint nut
Blindfold cap
Instruction Part
■ Thank you for your purchase of our “Combination Rack”.
■ Read this instruction manual carefully for correct and safety use.
■ Before using, be sure to read “Safety Precautions”.
Safety Precautions
Be sure to observe the following
precautions.
Caution
Be sure to
observe.
● Do not hang the door or handle.
Do not apply load exceeding the
allowable live load when opening
and closing the door.
The door or handle may be detached,
and accordingly injure you.
● Do not insert your hand into the
driving unit or between the
clearance of the main unit.
Your fingers may be caught and get
injured.
Be sure to
observe.
● Do not place hot water,
heated oil, keen knives or
other dangerous cooking
appliances in the temporary
storage area.
They may fall, and accordingly
injure you.
Applications of Parts
Storage area
Temporary storage area
Storage area
Live load: 3 kg or less
Temporary storage area
Live load: 5 kg or less
The upper storage area can accommodate
seasonings, wraps and paper towels
frequently used during cooking. When
opening the front panel, the storage area
comes down by about 40 mm to allow easy
reach even if lighting equipment is installed in
front of the cabinet.
The lower temporary storage area can
serve as a space where you can put a bowl
or tray containing pre-cooking foodstuff or
you can dish up food, allowing you to use a
cooking space effectively, which is likely to
be messed up.
Cleaning
● Daily cleaning
Wipe off the cabinet with water-moistened
firmly-squeezed cloth.
● When getting dirty
First wipe off the cabinet with
detergent-moistened cloth, then with
water-moistened cloth, and finally with dry cloth.
Instruction No. SCR-A01