Prospex® Plus XL PinholeTrim accent downlight for LED70
093+XL-13-LED-TR
Recessed adjustable pinhole trim downlights for use with all
Lucent LED70 modules including Ambiance WarmDim.
Die cast aluminium construction.
Seperate die cast installation kit for finished ceilings
Gear driven tilt and rotation.
Trimless versions available
Hot aiming simplifies focussing while lamp is on. Aiming
remains locked in focus throughout re-lamping.
Deep regressed lamp for minimal glare.
IP44 as standard.
Ref Number:
093+XL-13-LED-TR-WH
093+XL-13-LED-TR-BK
Lamp quantity
Lamp
Lamp holder
Lamp wattage
Adjustable
Aperture
Overall dimension
Overall height
Required depth
First fix requirement*
Ceiling cut out
Ceiling thickness
Ingress protection**
Dimming options***
White (RAL 9010)
Black (RAL 9005)
1
LED 70
n/a
12.6-25.2w
35°
75mm Ø
150mm Ø
140mm
165mm
Yes
142mm Ø
25mm MAX
IP44
Phase/DALI/1-10v
Cut out 142mm Ø
www.lucent-lighting.com
*First Fix requirement. Luminaire comprised of fixture body with separate ceiling trim and
installation kit, which is to be fitted into the ceiling once finished. Ensure correct alignment of the
installation kit before final assembly (see luminaire installation instructions for details).
**IP Rating. Tested from underside of the ceiling.
***Dimming. Whilst Lucent can offer the majority of its luminaires with various dimming options, it
remains the responsibility of the specifier/installer to check and ensure compatibility of any control
equipment used. Additional cabling may be required depending on the dimming protocol specified.
****Active Heatsink. Fixture with fan cooled heatsink to allow for larger output modules. Requires an
additional 12v supply for the fan. Enssure the correct driver is specified or an additional power supply
is provided.
It is the policy of Lucent Lighting to continually review and improve its products and therefore reserve the right to change any details of product or
withdraw specifications without prior notice.
Luminaires designed to comply with EN60598 and all other relevant Standards.
This Specification Sheet supersedes all previous versions
All intellectual property rights pertaining to the product described above and to this document are owned by or licensed to Lucent Lighting UK Ltd.
We reserve our right to take whatever action is necessary to protect those intellectual property rights.
Please notify Lucent Lighting Ltd of any inaccuracies immediately. E&OE
Job/Project Name
Area/Location
Contact Lucent Lighting: e: [email protected] t: +44 (0)20 8442 0880
Fitting Ref
Europe
China
Quantity
Russia
Lucent LED70 Range
Lucent's own range of 70mm diameter LED modules including the LED70
>80CRI and LED70-Ambiance Warm Dim, all utilising Cree XP-G2 white
LED's
Please refer to luminaire Specification sheet for maximum lumen output
that can be used within the fixture.
LED70
LED70 80CRI Module
LED70 module, RA > 80CRI using 12 x Cree XP-G2 LEDs
A choice of 3 colour temperatures 2700/3000/4000K & 2 Optic angles
14/32°.
Max Drive current 700mA, can be under run if required. Dimmable with
correct driver type. For dimming protocols available please consult
Lucent Lighting.
Module with on-board protection against surge and reverse polarity.
LED70 Order Code
LED Colour
2700K
27
3000K
30
4000K
40
Module Type
LED70
Example
Optic Angle
14 14°
32 32°
LED70-
30- 14
LED70 Ambiance WarmDim
LED70 Ambiance Warm Dim, RA > 80CRI using 9 x Cree XP-G2 & 3 x
XT-E LEDs
A choice of 2 main colour temperatures 2700/3000 dimming to 2200K.
Available in 2 optic angles 14/32°
Drive current 1000mA, Dimmable with correct driver type. For dimming
protocols available please consult Lucent Lighting.
LED70 Ambiance WarmDim Order Code
LED Colour
Optic Angle
2700K
27
14 14°
3000K
30
32 32°
Module Type
LED70WD
Example
LED70WD- 30- 14
www.lucent-lighting.com
* Separate die cast plaster in kit for plaster ceilings.
** Tested from ceiling underside. To specify IP54; add '-IP' to end of code.
policy of Lucent
Lighting
to continually
review and
its productsordered/specified).
and therefore reserve the right to change any details of product or
It is the
***
Dimming
options
depend
on driver
(to improve
be separately
withdraw specifications without prior notice.
Some control methods may require additional cabling
Luminaires designed to comply with EN60598 and all other relevant Standards.
This Specification Sheet supersedes all previous versions
All intellectual
property
rights pertaining
to the
described
above and
to this document
are owned
or licensed to Lucent Lighting UK Ltd.
Lucent
reserve
the right
to change
anyproduct
details,
dimensions
colours
etc without
priorbynotice.
We reserve our right to take whatever action is necessary to protect those intellectual property rights.
Please notify Lucent Lighting Ltd of any inaccuracies immediately. E&OE
Job/Project Name
Area/Location
Contact Lucent Lighting: e: [email protected] t: +44 (0)20 8442 0880
Fitting Ref
Quantity