061303-1
Part Number: LIN-201-03
INSTALLATION INSTRUCTIONS
LINCOLN NAVIGATOR
(2003-2006)
Always check our website for the most updated model year compatibility information.
NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT.
All instructions are written from the driver’s seat position looking forward at the vehicle dash. We advise caution whenever you are
removing or handling plastic parts of a vehicle’s dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break.
Logo and part number will be right-side up and readable when installed.
TOOLS NEEDED: Dash Trim Tool, (Part #SIT-104), #2 Phillips Screwdriver, Marking Pen.
PARTS INCLUDED: Three (3) #8x1/2” self tapping screws.
LOCATION OF MOUNT: To the right of the climate control.
Step 1.
Small Button
Start by setting the emergency brake. Open the arm rest just behind
transmission shifter. Locate a small button on the back of the windowswitch pod. With a sharp pointed object, push in the center pin on
this button to release a retainer clip that partially holds the switch pod.
Carefully lift the pod upward releasing two clips holding the front of the
pod. Disconnect all wiring to the pod and set it aside. Locate and remove
two (2) 7mm hex head screws that hold the shifter bezel in place. These
screws are located toward the back of the shifter bezel. Set the screws
aside. Using the Dash Trim Panel, get underneath the front left and right
corners of the shifter bezel and pull upward to release two (2) clips. Once
the bezel is loose, place the shifter knob into low gear.
Step 2.
Carefully lift the shifter bezel up and turn it clockwise. Locate and remove
two (2) 7mm screws in the cavity below the ashtray. See Picture.
Note: The whole bezel will need to be removed and can be awkward to maneuver it loose from the dash. After all the clips are loose,
use extreme caution removing the bezel. Insert the Dash Trim Panel tool
in the upper-right corner of the air vent on the radio climate control trim
bezel. Carefully pry the tool toward you to release the top-right clip. Continue working the bezel loose over to the top-left corner. Use the Dash
Trim tool to release the left and right sides of the bezel. There is a retainer
clip on both sides of the radio. Grasp the the bezel and work it loose.
Disconnect all wiring to the bezel and carefully lift the bezel away from
the dash and set it in a safe place.
Step 3.
Locate the flat area of plastic to the right of the radio and retaining clip
hole. Place the Custom Bezel Mount in this area making sure the mount is
snug in the corner. Insert the three (3) provided self-tapping screws and
tighten the Custom Bezel Mount in place. See Picture.
Carefully reinstall the dash trim bezel in reverse order. Install any
Bracketron phone holder or Amps compatible device to your Custom
Bezel Mount.
Your installation is complete.
© Bracketron Inc, 2007 All rights reserved.
The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor do we assume any liability in
connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information.
Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount.
Bracketron Inc will not be liable for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount.
Bracketron Inc. 5249 West 73rd Street, Suite G, Edina, MN 55439, Ph: 952-746-7775 Fax: 1-800-660-1784 Toll Free: 1-866-237-4443
Web Address: www.bracketron.com
071006-1
Part Number: LIN-201-03
INSTALLATION INSTRUCTIONS
DODGE RAM 1500, 2500
(2006-2007)
Always check our website for the most updated model year compatibility information.
NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT.
All instructions are written from the driver’s seat position looking forward at the vehicle dash. We advise caution whenever you are
removing or handling plastic parts of a vehicle’s dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break.
Logo and part number will be right-side up and readable when installed.
TOOLS NEEDED: Dash Trim Tool, (Part #SIT-104), #2 Phillips Screwdriver, Marking Pen, Razor Blade, Small Hand Drill, One
5/64” Drill Bit.
PARTS INCLUDED: Three (3) #8x1/2” self tapping screws.
LOCATION OF MOUNT: To the right of the radio..
Lower Right
Corner
Cut Notch
Mark Bezel
2.5 Inches
Notch Bezel
2.5 Inches
Step 1.
Begin by removing the trim bezel that surrounds the radio. To
do this start by opening up the drink holder below the climate
control. Locate two vertical Phillips head screws in the upper right
and left corners of this cavity. Set the screws aside. Carefully insert
the dash trim panel tool in the lower right corner of the bezel and
pry toward you releasing the first clip. Work your way around
the whole bezel releasing a series of clips until the bezel is loose.
Disconnect all wires to the bezel and set aside.
Step 2.
Locate a flat area just to the right of the air vent that is to the
right of the radio. There is a small lip that extends beyond this flat
spot. Measure a 2.5” area and mark with a marking pen. Carefully notch and remove this area with a sharp razor blade. Insert
the CBM over this flat area. Use the holes in the CBM as guides
to mark three spots for pilot holes. Set the CBM aside. Drill three
pilot holes with a small hand drill and a 5/64” drill bit. Insert the
CBM over the pilot holes and tighten the mount down with the
provided screws.
Step 3.
Carefully replace the bezel but do not connect any wiring or insert
the two screws that were removed. There is a plastic lip on the
ends of the bezel. Pull the bezel back toward you in the top right
corner where the CBM is mounted. Where this lip touches the
CBM, mark an area above and below the CBM on this lip. Remove
the bezel. CAREFULLY cut a notch out of this plastic lip. You will
do this so the bezel will seat down tight and all the clips will be
tight in the upper right corner of the bezel.
Carefully reinstall the dash trim bezel in reverse order making sure
all screws and clips and wiring is secure. Install any Bracketron
phone holder or Amps compatible device to your Custom Bezel
Mount.
Your installation is complete.
© Bracketron Inc, 2007 All rights reserved.
The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor do we assume any liability in
connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information.
Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount.
Bracketron Inc will not be liable for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount.
Bracketron Inc. 5249 West 73rd Street, Suite G, Edina, MN 55439, Ph: 952-746-7775 Fax: 1-800-660-1784 Toll Free: 1-866-237-4443
Web Address: www.bracketron.com