MODEL 2907
Ball Bearing Electronic Enclosure Slide
.38" [9.6 mm] Width
1.62" [41.1 mm] Height
2.00" [50.8 mm] Over Travel
Up to 115 lb. ¤ [52.3 kg] Capacity
Applications: Use model 2907 whenever an ultra-thin,
medium duty, over travel, rack-mount slide is required.
For use on electronic chassis, keyboards, fantrays, and
other rack-mount applications. Accommodates chassis
from 1U to 4U. This product is covered by U.S. and
various foreign patents issued and/or pending.
.213 [5.4] DIA. Through
Hole with .365 X .213 X
.040 [9.3 X 5.4 X 1.01]
Raised Emboss
.63
[15.9]
3.04
[77.2]
6.04
[153.4]
1.74
[44.2]
TYP.
1.25
[31.8]
.36
[9.1]
TYP.
.69
[17.5]
TYP.
Flush or at
.50 [12.7]
Under Only
.38
[9.6]
Adjustable From Flush
Plus 1.75 [44.5] or
Minus 2.00 [50.8]
Flush or Under
.192 X .413
[4.9 X 10.5]
TYP.
2.39
[60.7]
.50
[12.7]
TYP.
1.50
[38.1]
REF.
1.25
[31.8]
REF.
#8-32 Clinch Nut (5X)
Slide Travel
4.39
[111.5]
Clinch Nuts
#8-32 TYP.
1.25
[31.8]
Ref.
.50
[12.7]
REF.
Lock Out and
Lever Disconnect
.50
[12.7]
Slot Not Available On
12" [305] Slide Length
.192 DIA.
[4.9] TYP.
1.14
[29.0]
.50
[12.7]
.180 X .725
[4.6 X 18.4]
.38
[9.5]
3.00
[76.2]
1.62
[41.1]
A
.39
[9.9]
INCHES
[mm]
B
C
D
.35
[8.9]
TYP.
E
F
Access
Slots
.180 X 2.74
[4.6 X 69.6]
.180 X 1.49
[4.6 X 37.8]
.180 [4.6]
DIA. (2X)
Slide Length Minus .050 [1.3]
Finish
Clear electroplate (C) finish
Length
12"–30" [305 mm–762 mm]
Slide Length
Height
1.62" [41.1 mm]
¤ Load
Part
Slide Slide Rating per
Number Length Travel Pair lb.
[kg.]
Load
See chart ¤
2907-12
.38" ± 0.030 ** ‡ [9.6 mm ± 0.76 mm]
12.00
[305]
14.00
[356]
60 lb.
[27.2 kg.]
9.25
[235.0]
2907-14
14.00
[356]
16.00
[406]
80 lb.
[36.3 kg.]
11.25
[285.8]
13.25
[336.5]
Side Space
A
B
C
D
E
F
Travel
2.00" [50.8 mm] Over travel
Mounting
Chassis Member: #8 pan head screw
2907-16
16.00
[406]
18.00
[457]
100 lb.
6.40
[45.4 kg.] [162.6]
Features
uter Member: Adjustable front and O
rear mounting brackets
2907-18
18.00
[457]
20.00
[508]
115 lb.
[52.2 kg.]
6.49 12.38
[164.8] [314.3]
15.25
[387.3]
nhanded, lock-out and disconnect, U
lead-in pins
2907-20
20.00
[508]
22.00
[559]
114 lb.
[51.7 kg.]
6.78
8.00 14.03
[172.1] [203.2] [356.2]
17.25
[438.1]
2907-22
22.00
[559]
24.00
[610]
112 lb.
[50.8 kg.]
8.39 16.03
[213.0] [407.0]
19.25
[488.9]
2907-24
24.00
[610]
26.00
[660]
110 lb.
10.00 10.78
[49.9 kg.] [254.0] [273.7]
¤ Load rating based on an 16" [406 mm] wide
2907-26
26.00
[660]
28.00
[711]
110 lb.
5.53
9.15 10.60 16.40 20.03 23.25
[49.9 kg.] [140.3] [232.4] [269.1] [416.6] [508.6] [590.5]
Brackets behind EIA rail with square.
** No lateral adjustment with EIA rails using round
or tapped holes.
2907-28
28.00
[711]
30.00
[762]
110 lb.
7.53 11.15 12.00 18.40 22.03 25.25
[49.9 kg.] [191.1] [283.2] [304.8] [467.4] [559.4] [641.4]
2907-30
30.00
[762]
32.00
[813]
110 lb.
[49.9 kg.]
chassis cycled 2,000 times.
‡
18.03 21.25
[457.8] [539.7]
9.53 12.60 20.40 24.03 27.25
[241.9] [319.9] [518.2] [610.2] [692.1]
Installation Instructions
1. Slide chassis member (smallest) is removable. Separate slide members by lifting left hand side lever up, and right hand side
lever down. Keep slide chassis members with original outer
members.
2. Slide has front and rear adjustable EIA brackets. Attach front
brackets to outer slide member using #8-32 machine screws by
aligning access slots on brackets to outer member holes. Front
brackets can be mounted flush or 1/2" [12.7 mm] back from front
of slide based on user needs.
Figure 1
Cabinet Rail with
Square Holes
Bracket
Face
Emboss
Emboss
#8-32
provides
Threads
vertical alignment
(No Bar
Nut Required)
within square holes.
3. Establish distance from front cabinet rail to rear cabinet rail and
attach rear brackets to slide. Do not fully tighten rear bracket
mounting screws until final adjustment is made.
Bar Nut
Bar Nut
4. Insert removable locator pin into center hole of brackets.
5. Slide will mount to various cabinet rails at various locations on
side of chassis. See illustrations at right.
6. Place slide into desired position and fully extend against EIA
rails. Locator pins will support slide and bar nut while attaching screws.
7. Attach slide to EIA rail with #10-32 screws and fasten with bar
nuts. Once screws are secure, remove locator pins. Do not fully tighten screws until final adjustment is made.
8. Mount slide chassis members (smallest) to the chassis.
9.
With cabinet members in the open or closed position, bring ball retainer to full forward position. Install chassis by engaging the
slide members and close completely. Locks will engage on
initial insertion and must be released to fully close. Check
slide alignment by opening and closing the chassis. Any sign of
binding indicates lateral stress or misalignment.
10. Adjust slide position until movement is smooth. Tighten all screws and complete installation.
Front of Rail
.44" [11.1]
Side Space Required
Figure 2
Cabinet Rail with
Tapped Holes
Front of Rail
Removable
locator pin
supports slide
during installation
Front of Rail
.44" [11.1]
Side Space Required
OTE: To remove chassis, lift the lever on the left hand slide up and
N
the lever on the right hand slide down.
Figure 3
Slide Ordering Instructions
Cabinet Rail with
Round Holes
Complete your order for Accuride Model 2907 by specifying the
following information. For example:
Required Slides
Slide Finish
Slide Model
Slide Length
Optional Polybag Packaging 10 Pair
C
2907
-18
Behind Rail
(Recommended)
Bar Nut
Front of Rail
D
Removable
locator pin
supports slide
during installation
Figure 4
Optional Mounting Bracket Kit
Optional mounting bracket kit, part number 4180-0430-XE, includes (2)
front brackets, (2) rear brackets, (4) bar nuts, (4) locator pins, (8) #8-32
bracket-to-slide mounting screws, and (8) #10-32 bracket-to-rail mounting
screws packaged in a polybag.
Kits ordered separately. Order 1 kit per pair of slides.
Packaging
Behind Rail
(Recommended)
1/2"
For 2U to 4U spacing,
slides can mount to
chassis (drawer) at
various locations
relative to the EIA rail
1/2", 5/8", 5/8" pitch pattern.
5/8"
5/8"
1/2"
Bulk (P) Pack: All lengths are packaged 10 pair per box. Optional
mounting bracket kits (4180-0430-XE) are ordered and packaged
separately.
Distributor (D) Pack: All lengths are packaged 5 pair per box.
Polybag packaging includes one pair of slides, one mounting bracket
kit (4180-0430-XE), and installation instructions.
ACCURIDE INTERNATIONAL INC.
Specifications
12311 Shoemaker Avenue
Santa Fe Springs, CA 90670
Slide members and ball retainers: Cold rolled steel
Ball bearings: Carburized steel
RoHs compliant
TEL (562) 903-0200
FAX (562) 903-0208
www.accuride.com
Note: Specifications, materials, prices, terms, and delivery are subject to change without notice.
Manufacturing, Engineering, and Sales
For the most current technical information visit www.accuride.com
Copyright © 2012 Accuride International Inc. 3700-9456(1085)-MK091-R6-0912
United States • Germany • Japan • Mexico • United Kingdom • China