Recluse 2.5i, 2.5ni
& 3.0i air mats
RECLUSE INSTRUCTIONS
PUMP & INTAKE VALVE
EXHAUST VALVE
RECLUSE PAD (shown upside down, pump side up)
INSTRUCTION INDEX
Safety Warnings
Care & Cleaning
Inflating & Deflating your pad
Repair Instructions
Kelty Warranty
Save these instructions for future reference.
p. 2
p. 2
p. 3
p. 3
p. 4
-IMPORTANTRead and follow all Warnings and Instructions in the Safety
Instructions and on Recluse Pad. Failure to follow all Warnings
and Instructions could result in death or serious injury.
WARNINGS
SAFETY WARNING
DOs AND DO NOTs
• Save these pages for future reference.
INFLATION INSTRUCTIONS
1. Unfold pad flat on ground, clear of sharp objects.
2. Locate pump, place pad with pump unit facing up (Image A). Please
note* the pad is upside down during inflation. Open intake valve.
Image A, pump unit & intake
valve, valve open.
Image B, Exhaust valve.
3. Locate exhaust valve and make sure that it is closed. (Image B)
Image C, Pump unit
during compression.
Image D, Pump unit
valve closed.
DANGER means if the safety information is not followed
SAFETY INFORMATION
someone will be seriously injured or killed.
WARNING means if the safety information is not followed
someone could be seriously injured or killed.
CAUTION means if the safety information is not followed
someone may be injured.
BEFORE USING THE AIRBED FOR THE FIRST TIME,
UNDERSTAND THAT:
DANGER
• The Pad should never be used as a personal flotation
device, life preserver, raft or water toy.
WARNING
• Children should always be closely supervised when they are
using this pad
CAUTION
• Do not over inflate
DO NOT ATTEMPT TO REPAIR OR SERVICE THE AIR PUMP.
• The air pump is not serviceable.
• Do not try to disassemble, repair or service the pump.
2
CARE & MAINTENANCE
1. For best lifetime of this product never unfold or inflate this product
in temperatures below freezing.
2. Avoid prolonged exposure to sun.
3. Avoid contact with sharp objects.
4. Never allow sand or debris to enter pump intake valve.
5. Clean product with mild soap and water.
6. Never store pad when wet. Store unfolded in dry & cool place out
of direct sunlight
4. Compress the foam inside the pump unit with your hands as shown above
(Figure C). Inflate to your desired pressure. Be careful not to over inflate.
Typical inflation requires approximatly 100 cycles, sure beats huffing and
puffing! Allow foam to rebound between pumps. During rebound do not
block the intake valve with your hand.
5. When desired pressure has been achieved, replace cap on pump valve.
Take care not to cross thread the cap.
6. Turn pad over so that pump valve is now facing down. Why? Because the
the insulation (140g/m2) is bonded on this side hides the pump for a more
comfortable nights sleep. Enjoy!
DEFLATION INSTRUCTIONS
1. Open Exhaust valve and allow air to escape. It helps just to lay on it.
2. Fold pad in thirds (Image E) and roll from the foot (image F) towards the
head. This will push the remaining air out.
3. Close exhaust valve and place rolled up pad inside stuff sack.
Image E.
Image F.
INFLATION & REPAIR INSTRUCTIONS
SAFETY INFORMATION
REPAIR INSTRUCTIONS
1. Locate repair kit within stuff sack closure flap.
2. Deflate pad fully. For small punctures, apply small amount of glue to tip
of toothpick and insert into puncture. Reapply small amount of glue on
exterior to create small cap-like repair. Allow glue to dry overnight.
3. For tears or cuts: cut a small circular piece of patch fabic (included).
Apply glue to fabric patch (coated side) and to the damaged area.
Fabric patch may curl slightly, this is normal. Allow glue to become
tacky (30 seconds or so) then apply patch to damaged area and press
gently until bond forms. Allow glue to dry overnight.
3
10/02/2012
Kelty Limited Warranty
Kelty takes pride in the quality of our products and guarantees that the
materials and workmanship will be free from defects for the life of the
product (with the exception of furniture, sleeping pads and air beds, which
have a one year limited warranty). This is limited to original owners.
This warranty supersedes any other warranty and is subject to the
following conditions and limitations.
KELTY WARRANTY
Since no Kelty product is indestructible, Kelty’s warranty does not cover
defects attributable to or resulting from normal wear and tear (ie:
exhausted zippers), natural hazard damage (ie: weather, animals, ultraviolet [UV] damage on tents), abuse or alteration.
All products being returned require a Return Authorization number.
Service under warranty is available to the original purchaser by returning
the product to any authorized Kelty dealer or by contacting our service
department.
Please call 800.535.3589 or visit http://www.kelty.com/t-warranty.aspx
for more information.
If, after inspection, we determine that the product is defective, we will
repair or replace it at our discretion, free of charge. If your Kelty product
needs service or repair that is not covered under warranty, we will provide
the necessary service at a reasonable charge.
This warranty give you, the original purchaser, specific legal rights. You
may also have other rights which vary state to state.
4
6235 Lookout Road / Boulder / CO 80301
800.535.3589 • fax 800.504.2745 • www.kelty.com