SAFETY DATA SHEET
U.S. Department of Labor
Occupational Safety & Health Administration
Flashband
SECTION 1 - IDENTIFICATION
MANUFACTURER:
Andek Corporation
ADDRESS:
850 Glen Avenue, Moorestown, NJ 08057
TELEPHONE:
1-856-786-6900
In an emergency, contact CHEMTREC 1-800- 424-9300;
Outside the United States call +1-703-527-3887
PRODUCT IDENTIFIER: Flashband
RECOMMENDED USE:
Flashing Sealant
SECTION 2 – HAZARD IDENTIFICATION
SIGNAL WORD: Warning - No hazard in normal industrial use
HAZARD STATEMENTS:
Physical and Chemical Hazards: Not classified.
Human health:
Not classified.
Environment:
Not classified
PICTOGRAMS: Non required
PRECAUTIONARY STATEMENTS:
Prevention:
•
Use personal protective equipment as required.
•
Contact with molten material will cause thermal burns
Disposal:
•
Waste disposal should be in accordance with existing federal, state and local environmental control laws.
•
Incineration is the preferred method.
SECTION 3 – COMPOSITION:
disclosure.
No classified ingredients, or those having occupational exposure limits are present above the levels of
SECTION 4 – FIRST AID MEASURES
Skin:
•
If burned by contact with molten material, cool as quickly as possible with water.
•
Do not remove material from skin but keep affected area covered with cold, clean, wet compresses
Eyes: If splashed by molten material, seek medical attention immediately
Inhalation: N/A
Ingestion: Do not induce vomiting. Get medical attention immediately.
Recommendation for immediate medical care and special treatment needed, when necessary: No specific first aid measures noted
Page 1 of 3
Revision Date: 4/30/15
Flashband
SECTION 5 – FIRE-FIGHTING MEASURES
Extinguishing media:
•
This material is combustible but not flammable
•
Use fire-extinguishing media appropriate for surrounding materials
Special fire fighting procedures: Use protective equipment appropriate for surrounding materials
Special hazards arising from the substance or mixture: Fire or high temperatures creates: toxic gases/vapors/fumes of Carbon dioxide (CO²),
Carbon monoxide (CO)
SECTION 6 – ACCIDENTAL RELEASE MEASURES
Personal precautions: Wear protective clothing as described in Section 8 of this safety data sheet
Methods and materials used for containment: Pick up for recycling or disposal as appropriate
Cleanup procedures: Do not discharge into drains, water courses or onto the ground
SECTION 7 – HANDLING & STORAGE
Precautions for safe handling: Avoid contact with bitumen film.
Recommendations on the conditions for safe storage:
•
Store in factory sealed box in a dry, cool and well-ventilated place.
•
Keep in original container
SECTION 8 – EXPOSURE CONTROLS/PERSONAL PROTECTION:
Engineering controls: No particular ventilation requirements
Inhalation protection: N/A
Eye protection: Wear safety goggles to prevent any possibility of contact with molten material or repeated or prolonged contact with material in any
other form
Skin and body protections: Heat resistant gloves must be used if handling molten material
Other hygienic practices and protective equipment:
•
Wash promptly if skin becomes wet or contaminated.
•
Promptly remove any clothing that becomes contaminated.
•
When using do not eat, drink or smoke.
•
Wash hands at the end of each work shift and before eating, smoking and using the toilet.
•
Use appropriate skin cream to prevent drying of skin.
•
Do not smoke in work area
SECTION 9 – PHYSICAL AND CHEMICAL PROPERTIES:
Appearance: Aluminum foil with adhesive layer and release-paper backing
Color: Grey or Silver
SECTION 10 – STABILITY AND REACTIVITY
Reactivity: No specific reactivity hazards associated with this product
Chemical stability: Stable under normal temperature conditions
Incompatibility (materials to avoid): No incompatible groups noted
Hazardous decomposition products: Fire creates: Carbon monoxide (CO). Carbon dioxide (CO²)
Conditions to avoid: Avoid excessive heat for prolonged periods of time
SECTION 11 – TOXICOLOGICAL INFORMATION
Product is non hazardous but ingestion may cause obstruction
Page 2 of 3
Revision Date: 4/30/15
Flashband
SECTION 12 – ECOLOGICAL INFORMATION
Ecotoxicity: The product components are not classified as environmentally hazardous.
Biodegradation: N/A
Bioaccumulation potential: N/A
Mobility in soil: Not relevant, due to the form of the product
Other adverse effects: N/A
SECTION 13 – DISPOSAL CONSIDERATIONS
Waste Disposal Method:
•
Waste disposal should be in accordance with existing federal, state and local environmental control laws.
•
Incineration is the preferred method.
Empty Container Precautions:
•
Empty containers retain product residue; observe all precautions for product.
•
Container is recyclable but must be completely empty before sending to recycle
•
If container is to be disposed, ensure all product residues are removed prior to disposal
SECTION 14 – TRANSPORT INFORMATION
UN #
N/A
UN PROPER SHIPPING NAME:
Caulk
HAZARD CLASS:
N/A
PACKING GROUP:
N/A
ENVIRONMENTAL HAZARDS:
Not a Marine Pollutant
GUIDANCE ON TRANSPORT IN BULK: N/A
Transport labels required: This product is not regulated by the D.O.T.
SECTION 15 – REGULATORY INFORMATION
US Federal Regulation:
SARA 313: No Substance Listed
US State Right to Know Regulations: New Jersey, Massachusetts, Pennsylvania, Rhode Island
No Substance Listed
CA Prop 65: No Substance Listed
Canada: No Substance Listed
SECTION 16 – OTHER INFORMATION (HMIS RATING)
Health
1
Flammability
0
Physical Hazard
0
Personal Protection
E
_____________________________________________________________________________________________________________________
Disclaimer: Andek Corporation believes, to the best of its knowledge, information and belief, the information contained herein to be accurate and
reliable as of the issue date of this Safety Data Sheet (SDS). However, because the conditions of handling, use, and storage of these materials are
beyond Andek Corporation's control, we assume no responsibility or liability for personal injury or property damage incurred by the use of these
materials and make no warranty, expressed or implied, regarding the accuracy or reliability of the data or results obtained from their use. All
materials may present unknown hazards and should be used with caution. The information and recommendations contained in the SDS are offered
for the users’ consideration and examination. It is the responsibility of the user to determine the final suitability of this information and data and to
comply with all applicable international, federal, state and local laws and regulations.
Page 3 of 3
Revision Date: 4/30/15
Flashband