MET III
5x5 Grid
MET III is programmed with different
modes for users to experience different
challenges and train for response time and
accuracy to make shooting targets a much
more interesting sport.
Instruction Manual
PARTS LIST
MET III : 25 PCs
USB Adapters (Europe type/USA type): 3 PCs
TIMER：1 SET <Optional>
G2-201410-02-英
Push Button:
Control panel x 1: for Game mode setting
Start Button x 1: for timer <Optional>
Output: Include 3.5mm output terminal for speakers or amplifier.
Check all connectors and make sure are
well connected without losing or
disconnected.
Make sure the direction is correct before
assemble. Use following tools to assemble,
INSTALLATION
Upper frame
1
Lower frame
2
Insert footing into the lower
frame, then use 4mm allen
wrench to tighten the screws.
5
10mm
Socket wrench
3
Align screw holes by using allen
wrench (or small pole), then
insert screws.
6
Make sure all power cables are
plugged and power switch is on
before close the back plate.
Complete set
4
Put both spring washer and nut
on the other side of the screw,
then use 4mm Allen wrench and
10mm socket wrench to tighten.
7
Connect power cable.
4mm
Allen wrench
Open the back plate of the
timer, take out all accessories.
8
Pull out three pieces of USB
cables from the cable slot on
the left side
Connect the USB cables to the
back of the timer.
3) To start the game after game
SETUP
1) Once all cables are
connected, plug the power
cable to the wall socket
and turn on the power
switch.
Make sure the timer display correctly. If timer does not
display after switched on, open the back plate and double
check if all cables are securely connected including DC
plug from the timer as well as the AC plug on the power
socket.
2) Switch on the MET III (see NOTE 1), after MET III
completed starting process, all targets will be in blue
lights, then use control panel to set to game mode
between 3 to 7.
Start Button
<optional>
mode selected, press the Start
Button once and timer will activate.
Timer will stop if the last target has
been hit or game over.
NOTE 1 :
Power switch of 5 x 5 grid
Switch on the system:
Press power switch for 2
seconds.
System will make 2 sounds after switched on, the second
sound indicates the system is now ready to accept the
selection of game modes.
Game mode could be selected by Control panel.
If all targets are not in blue light after the power has been
switched on, then double check the followings,
Problem 1, if none of the targets are in blue light, then
check all wires to see if they all well connected. Make sure
USB cables and adapters are plugged in and switched on.
Problem 2, if a row of targets are not in blue light, then
double check the wire connections of the rows above and
below. However, if the first or fifth row is not in blue light,
then double check the power or USB adapters.
Problem 3, if any single target is not in blue light, then
double check the wire connection from that target.
The whole system will need to be rebooted after any of
above problem has been solved.
MET III 5x5 Grid
GAME MODE
UPDATES
Instruction
Manual
Mode 6: Hostage Mode
Red light: Hostile / Blue light: Hostage
Red light will be turn off after hit. Blue light will stay
light up after hit.
In a situation when last target was hit in red light,
then the game will restart itself without pressing any
button.
However, if any target was hit in blue light during the
game, then the game will not restart until the push
button is pressed again.
Mode 7: Time Bomb
After this mode is selected, the initial target will light
up in blue. The game starts after the blue initial
target has been hit, then targets will begin randomly
light up. Each target will only light up for 3 seconds,
if the lighted target has not been hit within 3 second
time, then this target will turn in red light and game
over. Timer will stop as soon as the game is over. To
restart the game, simply press the push button
again. However, the game will restart automatically
in standby mode if all targets have been hit.
(Game mode 1 and
2 are unavailable
in 5 x 5 grid.)
If Control panel is not
functioning, double check if
wires are well connected.
After upper part and lower
part of the frame assembled,
make sure 4 wires are
connected, 2PIN x 2,
3PIN x 1<Optional>, 5PIN x 1.
NOTE 2 : TIMER <Optional>
1) Pressing the button to zero or restart.
2) Pause timer by pressing the remote
controller if required, resume timer by
pressing the “CONTINUE” button on the
controller when ready.
OTHERS
The 5 x 5 grid is built with
speaker output, connect
the amplifier to the output
socket in cable slot on the
right hand side.
WARNING
This product has built in compact amplifier, keep out of
reach of children to avoid hearing injury.
Do not violate the local environmental regulation of
noise in public area, adjust volume accordingly.