220571
BOOT CARRIER
INSTRUCTIONS
Please read carefully for Boot Carrier installation
CONTACT US
021-797-6559
[email protected]
www.holdfast.co.za
@Holdfast_SA
www.facebook.com/HoldfastSA
8 WETTON PARK, DOLPHIN WAY, WETTON,
CAPE TOWN, SOUTH AFRICA
220571
BOOT CARRIER
Note: For a SEDAN the kink
on the carrier should be
facing downwards
Note: For a HATCHBACK
the kink on the carrier
should be facing upwards
MADE IN SOUTH AFRICA
220571
BOOT CARRIER
INSTRUCTIONS
Please read carefully for Boot Carrier installation
INSTRUCTION
MANUAL
CONTACT US
021-797-6559
[email protected]
www.holdfast.co.za
@Holdfast_SA
www.facebook.com/HoldfastSA
8 WETTON PARK, DOLPHIN WAY, WETTON,
CAPE TOWN, SOUTH AFRICA
220571
BOOT CARRIER
Note: For a SEDAN the kink
on the carrier should be
facing downwards
Note: For a HATCHBACK
the kink on the carrier
should be facing upwards
MADE IN SOUTH AFRICA
INSTRUCTION
MANUAL
STEP 4: Position your carrier
onto the boot of your vehicle.
STEP 1: Loosen levers.
Lift and turn lever
clockwise to loosen.
STEP 2: Using your foot
to support the bottom
of the rack, firmly pull
the carrier arms up and
into position.
STEP 3: There should
be an angle of roughly
90º for a SEDAN and
roughly 100º for a
HATCHBACK. Once the
rack is at the correct
angle tighten levers
again.
STEP 5: Use the clear stickers
provided to protect your vehicles
paint before attaching hooks.
Hook TOP stabilising straps into
the gap between the roof and
the boot of your vehicle. NOTE:
Do not hook onto your spoiler
90º
SEDAN
100º
HATCH
BACK
NOTE: If you need to change the
kink in the rack from a Sedan setup
to a Hatch setup, you will need to do
the following:
•
Removed levers and bolts on
both sides of the arms completely.
•
Remove the upper arms completely and flip them over.
•
Reattached bolts and levers
STEP 7: Hook the silver hook of
the SIDE stabilising strap onto
the lower bracket of your carrier
(just below the tightening clamp).
Then hook the black hook into
the gap between the side and
the boot of your vehicle.
STEP 4: Position your carrier
onto the boot of your vehicle.
STEP 1: Loosen levers.
Lift and turn lever
clockwise to loosen.
STEP 2: Using your foot
to support the bottom
of the rack, firmly pull
the carrier arms up and
into position.
STEP 3: There should
be an angle of roughly
90º for a SEDAN and
roughly 100º for a
HATCHBACK. Once the
rack is at the correct
angle tighten levers
again.
NOTE: If you need to change the
kink in the rack from a Sedan setup
to a Hatch setup, you will need to do
the following:
•
Removed levers and bolts on
both sides of the arms completely.
•
Remove the upper arms completely and flip them over.
•
Reattached bolts and levers
STEP 6: Use the clear stickers
provided to protect your vehicles
paint before attaching hooks.
Hook BOTTOM stabilising
straps into the gap between the
bumper and the boot of your
vehicle.
STEP 5: Use the clear stickers
provided to protect your vehicles
paint before attaching hooks.
Hook TOP stabilising straps into
the gap between the roof and
the boot of your vehicle. NOTE:
Do not hook onto your spoiler
90º
SEDAN
100º
HATCH
BACK
STEP 6: Use the clear stickers
provided to protect your vehicles
paint before attaching hooks.
Hook BOTTOM stabilising
straps into the gap between the
bumper and the boot of your
vehicle.
STEP 7: Hook the silver hook of
the SIDE stabilising strap onto
the lower bracket of your carrier
(just below the tightening clamp).
Then hook the black hook into
the gap between the side and
the boot of your vehicle.
STEP 8
Pull and tighten all six stabilising straps.
Your rack is now mounted and ready to
carry your bicycles.
WARNING: ENSURE THAT YOUR REAR WINDSCREEN WIPER IS
DISENGAGED WHEN YOUR BOOT CARRIER IS FITTED.
DO NOT OVERSTRETCH RUBBER BIKE CLAMPS
BEWARE OF MOUNTING THIS RACK ONTO PLASTICS SPOILERS.THIS RACK MAY
DAMAGE PLASTIC SPOILERS THAT CAN NOT TAKE THE WAIT OF THE RACK.
WEIGHT LIMIT: 45KG (15KG PER BICYCLE)
IMPORTANT: IF THE REAR NUMBER PLATE IS OBSCURED WHEN IN TRANSIT, IT IS
REQUIRED BY LAW THAT A NUMBER PLATE BOARD IS USED. THESE ARE
AVAILABLE FROM YOUR HOLDFAST DEALER.
STEP 8
Pull and tighten all six stabilising straps.
Your rack is now mounted and ready to
carry your bicycles.
WARNING: ENSURE THAT YOUR REAR WINDSCREEN WIPER IS
DISENGAGED WHEN YOUR BOOT CARRIER IS FITTED.
DO NOT OVERSTRETCH RUBBER BIKE CLAMPS
BEWARE OF MOUNTING THIS RACK ONTO PLASTICS SPOILERS.THIS RACK MAY
DAMAGE PLASTIC SPOILERS THAT CAN NOT TAKE THE WAIT OF THE RACK.
WEIGHT LIMIT: 45KG (15KG PER BICYCLE)
IMPORTANT: IF THE REAR NUMBER PLATE IS OBSCURED WHEN IN TRANSIT, IT IS
REQUIRED BY LAW THAT A NUMBER PLATE BOARD IS USED. THESE ARE
AVAILABLE FROM YOUR HOLDFAST DEALER.