1
Cesium Formate Product Specifications
Measured
Property
Typical
Solution Basis
Formulation
Typical Maximum
Specification
2.3
18.8
2.4
20
10.00 - 11.00
11.00
< 30 NTUs
average particle size
< 0.5 µm
Comment
Density
specific gravity S.G.
pounds per gallon ppg
pH
Turbidity
Particle Size Analysis
Viscosity @25 0C
Fann 35 @25 0C
Elemental (ppm)
5.65 cps
10:1 Dilution Reading/Fisher pH Paper
Solution Clarity
Malvern Particle Size Analyzer
Density Dependent
< 50
< 50
25
1
8
3
4
< 10
<3
<1
5
150
500
50,000
< 100
< 100
< 40
< 10
< 50
<5
<5
< 50
<5
<5
< 10
< 200
< 1000
<1
Dependent on Base Mineral Stream
Dependent on Manufacturing Process
Elements from Base Mineral
Dependent on Manufacturing Process
CO3
Citric Acid
1290
150
3680
150
Added for Buffering Capacity
Added Immediately After Final
Filtration
Insolubles
100
< 500
Measured at 250C
Σ Rb, K, Na, Li
Ba, Sr
Σ Ba, Sr, Ca, Mg
Al
Fe
Si
B
Mo
Tl
Σ Cu, Cr, Ni
Mn
P
SO4
Cl
Pb
Additives (ppm)
NOTE: Final specifications and chemical properties will vary on base ore source and for customized user requirements.
08/14
2
ecember 16, 1997
Measured
Property
Cesium/Potassium Formate Product Specifications
Typical
Solution Basis
Formulation
Typical Maximum
Specification
1.65
13.75
2.2
18.33
10.00 - 11.00
11.00
< 30 NTUs
average particle size
< 0.5 µm
5.65 cps
Comment
Density
specific gravity S.G.
pounds per gallon ppg
pH
Turbidity
Particle Size Analysis
Viscosity @25 0C
Fann 35 @25 0C
Elemental (ppm)
Cs
K
Σ Rb, Na, Li
Ba, Sr
Σ Ba, Sr, Ca, Mg
Al
Fe
Si
B
Mo
Tl
Σ Cu, Cr, Ni
Mn
P
SO4
Cl
Pb
10:1 Dilution Reading/Fisher pH Paper
Solution Clarity
Malvern Particle Size Analyzer
Density Dependent
8,300
68,400
35,000
< 50
< 50
25
1
8
3
4
< 10
<3
<1
5
150
500
74,700
7,600
50,000
< 100
< 100
< 40
< 10
< 50
<5
<5
< 50
<5
<5
< 10
< 200
< 1000
<1
CO3
Citric Acid
1290
100
3680
150
Added for Buffering Capacity
Added Immediately After Final
Filtration
Insolubles
100
< 500
Measured at 250C
Dependent on Base Mineral Stream
Dependent on Manufacturing Process
Elements from Base Mineral
Dependent on Manufacturing Process
Additives (ppm)
NOTE: Final specifications and chemical properties will vary on base ore source and for customized user requirements.
08/14
3
December 16,
Measured
Property
Formate Brine Buy-Back Specifications
Original
Solution Basis
Formulation
Return
Specification
For Buy-Back
1.65
13.75
1.65
13.75
1.5%
0.5%
10.00 to 11.00
< 30 NTUs
average particle size
< 0.5 µm
cps
Comment
Density
specific gravity S.G.
pounds per gallon ppg
suspended solids
hydrocarbon content
pH
Turbidity
Particle Size Analysis
Viscosity @25 0C
Fann 35 @25 0C
Elemental (ppm)
Cs
K
Σ Rb, Na, Li
Ba, Sr
Ca
Σ Ba, Sr, Mg
Al
Fe
Si
B
Mo
Tl
Σ Cu, Cr, Ni
Mn
P
SO4
Cl
Pb
10.00 - 11.00
cps
10:1 Dilution Reading/Fisher Paper
Solution Clarity
Malvern Particle Size Analyzer
Density Dependent
8,300
68,400
35,000
< 50
<10
< 50
25
1
8
3
4
< 10
<3
<1
5
150
500
8,300
68,400
50,000
< 100
< 50
< 100
< 40
< 10
< 50
<5
<5
< 50
<5
<5
< 10
< 200
< 2500
<1
CO3
Citric Acid
1290
100
3680
150
Added for Buffering Capacity
Added Immediately After Final
Filtration
Insolubles
100
< 500
Measured at 250C
Dependent on Base Mineral Stream
Dependent on Manufacturing Process
5 times original spec
Elements from Base Mineral
5 times original spec
5 times original spec
Additives (ppm)
NOTE: Cabot Specialty Fluids reserves the right not to buy-back any fluid that exceeds these specifications.
08/14