Carpenter
SDP Accreditation Checklist
Accrediting ETQA
e.g. QCTO or SETA Name
SDP Name:
Centre Manager Name
SDP Contact Details
SDP Physical Address
e.g. 17 Tonga-tinge Street, Mable Hall, 1612
Facilitator Name
Facilitator qualification
relevant to the trade
SME Name
SME Employer Details
SME Employer contact
Ratio of learners to
facilitator
e.g. 12 Candidates:1 Facilitator
No. of Candidates per
given time in the Venue
Accreditation History (If previously accredited through the SETA System, Complete the section below )
Accredited by:
SETA Name
Accreditation Visit Date:
Accreditation No.
DD/MM/CCYY
Province
OFO Code (if applicable)
e.g. Northern Cape
Municipality
e.g. Madibeng
New Accreditation Information
Knowledge
X
Practical Skills
OFO Code
Specialization /
Alternative Title
SAQA ID
Legacy Trade
Urban
Version
Signature:
New Trade
X
Rural
X
Audit Visit Date
DD/MM/YYYY
NADQAC: Skills Development Provider Accreditation Checklist
4 of 2016
Doc Ref.
SDP Checklist
Doc. No.
Page
1 of 8
Date revised
0005/2016
23/02/2016
Carpenter
Index of Tasks:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Roof structures
Form-work: (Steel)
Form-work: (Wood)
Hang of door
Circular Arch
Ceilings
Wall paneling
Install skirting and architrave
Setting out
Determine Levels
Scaffolding
Clad roof structure
NB: SME must ensure that all equipment were tested and found in good working condition for SDP!
Hand Tools
Ratio
Smoothing plane
1:1
Trying plane
1:1
Rebate plane
1:5
Tennon saw
1:1
Panel saw
1:1
Crosscut saw
1:2
Coping saw
1:5
Rip saw
1:5
Belly brace / Carpenters ratchet brace
1:1
Auger bit (9/10mm)
1:1
Auger bit 16mm
1:1
Auger bit 18mm
1:1
Bradawl
1: 5
Chisel set (6 mm – 25 mm)
1:1
Mitre square/Combination square
1:1
Rafter square
1:3
Centre punch
1:3
Nail punch
1:3
Claw hammer
1:1
Panel hammer (cross or peen)
1:3
Mallet wood or rubber
1:1
Version
Signature:
Y
N
NADQAC: Skills Development Provider Accreditation Checklist
4 of 2016
Doc Ref.
SDP Checklist
Doc. No.
Page
2 of 8
Date revised
0005/2016
23/02/2016
Carpenter
Sliding bevel
1:1
Yankee 420 mm
1:5
Oil stone
1:3
Hack saw
1:3
Chalk line
1:5
Ceiling knife
1:5
Spirit level (600mm or 1m )
1:3
Building line (fish line)
1:3
Screw driver set (combination star and flat )
1:1
Sash clamps
1:3
G clamps
1:3
Tool box (carpenter steel tool box)
1:1
Nail bag
1:1
Pliers
1:1
Pincer
1:3
Tinsnip Set
1:15
Comments:
Special Tools
Crowbar
1:5
Comments:
Measuring Equipment
Measuring tape 3 or 5 m
1:1
Measuring tape 10 or 20 m
1:5
Marking gauge
1:5
Version
Signature:
NADQAC: Skills Development Provider Accreditation Checklist
4 of 2016
Doc Ref.
SDP Checklist
Doc. No.
Page
3 of 8
Date revised
0005/2016
23/02/2016
Carpenter
Mortise gauge
1:1
Mitre box
1:1
Folding ruler
1:3
Comments:
Machinery
Portable planer machine
1
Portable drilling machine
1
Portable circular machine / skill saw
1
Portable belt sander
1
Orbital sander
1
Jig saw
1
Router machine
1
Comments:
Equipment (Long Term Consumables)
Dumpy Level
1
Staff
1
Tripod stand
1
Stepladder (folding)
1
Scaffolding (4 sets)
Ferrule jack
1
Trestles
4
Steel circular columns (1 set) 2.4m height
1
Steel formwork for walls (1 set) 300 mm width x 2.4
m length x 1.2 m height
Steel formwork for beam & slab (1 complete set )
1
1
Comments:
Version
Signature:
NADQAC: Skills Development Provider Accreditation Checklist
4 of 2016
Doc Ref.
SDP Checklist
Doc. No.
Page
4 of 8
Date revised
0005/2016
23/02/2016
Carpenter
Consumables
S.A.P. 114 x 38
S.A.P. 76x 38
S.A.P. 38 x 38
Roof tiles
Corrugated galvanized sheet metal
Nails 75 mm
Nails 100 mm
Door 2030 x 815 x 44
Mortise lock
1:1
Screws (Mortise lock)
Screws (Butt hinges)
Butt hinges (1 set )
1:1
Ceiling boards
Cornice
Clout nails
Grounds (for wall paneling)
T & G boards
Skirting
Panel pins
Architraves
Floor board T & G
Comments:
Assessment Aids
Version
Signature:
NADQAC: Skills Development Provider Accreditation Checklist
4 of 2016
Doc Ref.
SDP Checklist
Doc. No.
Page
5 of 8
Date revised
0005/2016
23/02/2016
Carpenter
Structure (for ceiling)
Structure (for wall paneling)
Structure (for skirting and architraves)
L – shape structure (for roof)
Structure (for hanging of doors)
Structure (for circular Arch)
Area for Form-work (steel)
Area for Form-work (wood)
Work bench with vise
1:2
External corner angle
Wedge set
Ferrules
Ferrule rose
Distance pipes (conduit/galvanize/asbestos )
Structure for partitioning(wood /aluminum)
Lift shaft structure (optional)
Area for setting out building
Structure for determining levels
Structure for beam & slab
Structure for open shelving
Comments:
Safety
Safety boots/shoes
1:1
Safety helmet
1:1
Protective clothing
1:1
Leather gloves
1:1
Goggles
1:1
Comments:
Version
Signature:
NADQAC: Skills Development Provider Accreditation Checklist
4 of 2016
Doc Ref.
SDP Checklist
Doc. No.
Page
6 of 8
Date revised
0005/2016
23/02/2016
Carpenter
I, _________________________ (manager of the trade test centre / skills development provider) hereby commits to
comply with all the relevant OHS regulations and sections applicable to this specific trade.
Signature and date
LOGISTICS AND LAY-OUT
Panel proportional to the number of candidates
Workshops for practical component
classroom
I ……………………………………… the undersigned, hereby declare that all the
tools/equipment/training materials/machines were checked and are the sole property of the
SDP.
Signature ……………………………….
Accreditation recommended
Date:……………………
Yes
No
Constraints/Gaps:
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
_______________________________________________________________________
Recommendations:
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
_______________________________________________________________________
SME Name
Date: DD/MM/YYYY
Signature
Organizational Rep. Name
Version
Signature:
NADQAC: Skills Development Provider Accreditation Checklist
4 of 2016
Doc Ref.
SDP Checklist
Doc. No.
Page
7 of 8
Date revised
0005/2016
23/02/2016
Carpenter
Designation
Date: DD/MM/YYYY
Signature
Version
Signature:
NADQAC: Skills Development Provider Accreditation Checklist
4 of 2016
Doc Ref.
SDP Checklist
Doc. No.
Page
8 of 8
Date revised
0005/2016
23/02/2016