Sheen
VISCOSITY
REF. 450N AUTOVISC
TM
ABCDE
FLOW CUP TIMER
FEATURES
•
•
•
Simple, rapid set up and operation
Accurate, repeatable results
Accepts a wide range of cups
•
•
•
Aluminium water jacket for temperature control
Portable, Alkaline battery power supply
Mains power supply 220V, 50Hz / 110V 60
INTRODUCTION:
The new Sheen Autovisc TM has been developed to provide users with an accurate and repeatable method
for standardising liquid flow-time measurements.
The Autovisc has been designed to accept most types of internationally recognised flow cups.
Combined with Sheen's range of flow cups, this instrument provides solutions to all flow time measurement
requirements.
OPERATION:
1. Level the instrument by inserting an empty flow cup into the water jacket, place the levelling bubble on
top of the cup and adjust the Autovisc feet until the cup is level.
OPERATION:
1.
Level the instrument by inserting an empty flow cup into the water jacket, place the levelling bubble on
top of the
cupcup
andand
adjust
the on
Autovisc
feet
until
thestand
cup isensuring
level. that the orifice is completely sealed.
2.
Select
a flow
locate
the flow
cup
filling
OPERATION:
1. Level the instrument by inserting an empty flow cup into the water jacket, place the levelling bubble on
top of the
cupcup
andand
adjust
the on
Autovisc
feet
until
thestand
cup isensuring
level. that the orifice is completely sealed.
2.
Select
aflow
flow
locate
the
flow
cup
filling
3.
thethe
cup with
fluid
and slide
top
cover
over
thethe
surface
that excess
liquid
is removed
1. Fill
Level
instrument
by
inserting
anthe
empty
flow
cup
into
water so
jacket,
place the
levelling
bubbleand
on
a
vacuum
seal
is
formed.
top
of
the
cup
and
adjust
the
Autovisc
feet
until
the
cup
is
level.
2. Fill
Select
flowcup
cupwith
andfluid
locate
the the
flowtop
cup
fillingover
stand
thatthat
theexcess
orifice is
completely
sealed.
3.
the aflow
andon
slide
cover
theensuring
surface so
liquid
is removed
and
a
vacuumflow
seal
is from
formed.
4.
Remove
the
cup
the stand
andflow
insert
into
the stand
aluminium jacket.
If the
necessary,
equilibrate
tosealed.
the
2.
Select
cup
andfluid
locate
the
cup
filling
thatthat
orifice is
completely
3. desired
Fill the aflow
cup
with
andon
slide
the top
cover
over theensuring
surface so
excess
liquid
is removed
and
temperature.
a
vacuum
seal
is
formed.
4.
thecup
cupwith
fromfluid
the and
stand
andthe
insert
the
aluminium
jacket.
If necessary,
equilibrate
to theand
3. Remove
Fill the flow
slide
top into
cover
over
the surface
so that
excess liquid
is removed
desired
temperature.
5. Switch
on
the
power,
reset
the
timing
function
and
zero
the
display.
The
instrument
will
now
start
a
vacuumthe
seal
is from
formed.
4. automatically
Remove
cup
theflow
stand
and insert into the aluminium jacket. If necessary, equilibrate to the
once
liquid
commences.
desired
temperature.
5.
onthe
thecup
power,
the timing
function
the display.
instrumentequilibrate
will now start
4. Switch
Remove
fromreset
the stand
and insert
intoand
the zero
aluminium
jacket.The
If necessary,
to the
automatically
once
liquid
flow
commences.
6. Place
a
suitable
receptacle
underneath
the
flow
cup
and
remove
the
cover
plate
by
sliding smoothly
desired
temperature.
5. Switch on the power, reset the timing function and zero the display. The instrument will now start
from the cup. Instrument timing will start immediately and will stop as soon as a break occurs in the
automatically
once
liquid flow
commences.
6.
Place
aon
suitable
receptacle
underneath
the
cup
andthe
remove
theThe
cover
plate by will
sliding
Thepower,
LCD
shows
thetiming
elapsed
timeflow
ofand
the
fluid
flow.
5. liquid
Switchflow.
the
reset the
function
zero
display.
instrument
nowsmoothly
start
from
the
cup.
Instrument
timing
will
start
immediately
and
will
stop
as
soon
as
a
break
occurs
in the
once
liquid flow
commences.
6. automatically
Place
a
suitable
receptacle
underneath
the
flow
cup
and
remove
the
cover
plate
by
sliding
smoothly
liquid
flow.
The
LCD
shows
the
elapsed
time
of
the
fluid
flow.
7. Remove the cup and the waste receptacle and clean any residual fluid from the instrument.
from the cup. Instrument timing will start immediately and will stop as soon as a break occurs in the
6. Place
a suitable
receptacle
underneath
the
flow
cupfluid
andflow.
remove the cover plate by sliding smoothly
liquid reading
flow.
LCD
shows
the elapsed
time
of clean
the
7. Take
Remove
theThe
cup
and
thethe
waste
receptacle
and
any residual
fromas
the
instrument.
8.
and
reset
Time
End
switch.
from the
cup.
Instrument
timing
will
start
immediately
and
will stop fluid
as soon
a break
occurs in the
liquid
flow.
The
LCD
shows
the
elapsed
time
of
the
fluid
flow.
7. Zero
Remove
the cup
and
thethe
waste
anymeasurement.
residual fluid from
instrument.
8.
Take
reading
andand
reset
Timereceptacle
End
9.
the
display
the
instrument
is switch.
readyand
for clean
the next
If no the
further
measurements are
needed,
switch
offand
thethe
Autovisc
to preserveand
battery
life.
Remove
the cup
waste
clean
any residual fluid from the instrument.
Take the
reading
andand
reset
Timereceptacle
End
Zero
display
thethe
instrument
is switch.
ready for the next measurement. If no further measurements are
needed,
switch
offreset
the Autovisc
preserve
battery life.
8.
reading
and
TimetoEnd
9. Take
Zero the
display
and thethe
instrument
is switch.
ready for the next measurement. If no further measurements are
SPECIFICATION:
needed, switch off the Autovisc to preserve battery life.
9. Zero the display and the instrument is ready for the next measurement. If no further measurements are
SPECIFICATION:
Digital
Counter:
0-99999.9
0.1battery
secondlife.
increments
needed,
switch off the
Autoviscseconds,
to preserve
Max. cup diameter:
58mm
SPECIFICATION:
Digital
Counter:
0-99999.9
seconds, 0.1 second increments
Max. cup
orifice:
8mm
Max.
cup
diameter:
58mm
H x W x D:
300 x 210 x 210mm
SPECIFICATION:
Digitalcup
Counter:
0-99999.9 seconds, 0.1 second increments
Max.
orifice:
8mm
Weight:
3.5kg
net
Max.
cup
diameter:
58mm
H
x
W
x
D:
300
x
210
x 210mm9V alkaline batteries
Power
Supply:
Portable
operation:
Digital
Counter:
0-99999.9
Max. cup
orifice:
8mm net seconds, 0.1 second increments
Weight:
3.5kg
Mains
operation:
220V 50Hz / 110V 60Hz
Max.
58mm
H x Wcup
xSupply:
D:diameter:
300 x 210operation:
x 210mm9V alkaline batteries
Power
Portable
(European,
UK
and
USA plugs supplied)
Max.
cup orifice:
8mm
Weight:
3.5kg net
Mains
operation:
220V
50Hz / 110V 60Hz
Temp/AH
range:
+
15
+35°C,
80%
AH
H
x W xSupply:
D:
300
x 210operation:
x 210mm9V alkaline
Power
Portable
batteries
(European,
UK
and
USA
plugs supplied)
Accuracy:
±0.5%
Weight:
3.5kg
net
Mains
operation:
220V
50Hz / 110V 60Hz
Temp/AH
range:
+
15
+35°C,
80%
AH
Repeatability:
±0.5%
Power Supply:
Portable
operation:
alkaline
batteries
(European,
UK and 9V
USA
plugs supplied)
Accuracy:
±0.5%
Mains
operation:
220V
Temp/AH range:
+ 15 - +35°C,
80%
AH 50Hz / 110V 60Hz
Repeatability:
±0.5%
(European,
UK and USA plugs supplied)
Accuracy:
±0.5%
Temp/AH
range:
+
15
+35°C,
80% AH
Repeatability:
±0.5%
ORDERING
INFORMATION:
Accuracy:
±0.5%
Repeatability:
±0.5%
ORDERING
INFORMATION:
Ref 450N: Autovisc
supplied with cover plate, flow cup filling stand, spirit level and ISO adapter sleeve
7.
8.
9.
ORDERING
INFORMATION:
Ref
450N: Autovisc
supplied with cover plate, flow cup filling stand, spirit level and ISO adapter sleeve
ORDERING
INFORMATION:
Ref 450N: Autovisc
supplied with cover plate, flow cup filling stand, spirit level and ISO adapter sleeve
RELATED PRODUCTS - Please ask for Data sheet
Ref 450N: Autovisc supplied with cover plate, flow cup filling stand, spirit level and ISO adapter sleeve
RELATED
PRODUCTS
- Please
for Data
sheet
Ref
441:
Calibration oils
(500ml)ask
±0.2%
accuracy
Ref 401:
Flow Cup, conforming to BS3900:A6:1971
RELATED
PRODUCTS
- Please ask for Data sheet
Ref 406:
441:
Calibration
oils (500ml)to±0.2%
Flow Cup, conforming
ASTMaccuracy
D1200
401:
BS3900:A6:1971
Ref
417:
Flow
Cup,
conforming
to
BS
EN
ISOsheet
2431, BS3900:A6, 1996 and ASTM 5125
RELATED
PRODUCTS
Please
ask
for
Data
Ref 404:
441:
Calibration
oils (500ml)to±0.2%
accuracy
406:
ASTM
D1200
Ref
Flow
Cup, conforming
DIN
53211
Ref 417:
401:
Flow Cup,
Cup, conforming
conforming to
to BS
BS3900:A6:1971
Ref
Flow
ENaccuracy
ISO 2431, BS3900:A6, 1996 and ASTM 5125
Ref
441:
Calibration
oils (500ml)to±0.2%
Ref
406:
Flow
Cup,
conforming
ASTM
D1200
Ref
404:
Flow
Cup,
conforming
to
DIN
53211
Ref
Flow
to BS
BS3900:A6:1971
Ref 401:
417:
Flow Cup,
Cup, conforming
conforming to
EN ISO 2431, BS3900:A6, 1996 and ASTM 5125
Ref
406:
Flow
Cup,
conforming
to
ASTM
D1200
Ref
404:to continuous
Flow
Cup, conforming
DIN
Owing
development,
we reservetothe
right53211
to introduce improvements and modify specifications without prior notice.
Ref 417:
Flow Cup, conforming to BS EN
ISO 2431, BS3900:A6, 1996 and ASTM 5125
Ref 404:
Flow Cup, conforming to DIN 53211
Owing to continuous development, weSheen
reserve the rightInstruments
to introduce improvements and
modify specifications without prior notice.
Ltd
Unit 4, St. Georges Ind. Est., Richmond Road, Kingston, KT2 5BQ England.
Owing to continuous development, we reserve the right to introduce improvements and modify specifications without prior notice.
Instruments
Tel: 020 8541 4333 Sheen
Fax: 020 8549 3374
Intl.Tel: 44 20 8541 4333Ltd
Intl.Fax: 44 20 8549 3374
01/05
Internet
: www.sheeninstruments.com
Email:
[email protected]
Unit
4,
St.
Georges
Ind.
Est.,
Richmond
Road,
Kingston,
KT2
5BQ England.
Owing to continuous development, we reserve the right to introduce improvements and modify
specifications without prior notice.
Sheen Instruments Ltd
01/05
01/05
01/05
Tel: 020 8541 4333 Fax: 020 8549 3374 Intl.Tel: 44 20 8541 4333 Intl.Fax: 44 20 8549 3374
UnitInternet
4, St. Georges
Ind.Essor
Est., Richmond Road, Email:
Kingston,
KT2 5BQ England.
Labomat
[email protected]
Essor
: www.sheeninstruments.com
37 Bld Anatole France
VlamingstraatLtd
4
Sheen
Instruments
Tel: 020 8541 4333 Fax:F020
8549
Intl.Tel: 44 20
4333 Intl.Fax: 44 20 8549 3374
- 93287
Saint3374
Denis Cedex
B - 8541
8560 Wevelgem
UnitInternet
4, St. Georges
Richmond
Kingston,
5BQ England.
Tel.: Ind.
+33 1 Est.,
48 09 66
11 Road,
Tel.:Email:
+32 56 43
28KT2
13
: www.sheeninstruments.com
[email protected]
Fax: +33 1 48 09 98 65
Fax: +32 56 43 28 14
Tel: 020 8541 4333 Fax:E-mail :
020 8549
3374 Intl.Tel:E-mail :
44 [email protected]
8541 4333 Intl.Fax: 44 20 8549 3374
[email protected]
Internet : www.sheeninstruments.com
Email:
[email protected]
www.labomat.eu
www.labomat.eu
eeeee